Panasonic AW-HN130WPC User manual

DVQP1713ZA
W0218TY0 -FJ
ENGLISH
Model No. AW‑HN130WPC
Model No. AW‑HN130KPC
Model No. AW‑HN130WE
Model No. AW‑HN130KE
Operating Instructions
HD Integrated Camera
Before operating this product, please read the instructions carefully and save this manual for future use.
Please carefully read the “Read this first!” (pages 2 to 6) of this Manual before use.
PC EJ

Read this first! (For AW‑HN130WPC, AW‑HN130KPC)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws and drop-prevention wire mounting screw out of the
reach of infants and small children.
CAUTION:
This apparatus can be operated at a voltage in the range of 100
– 240 V AC.
Voltages other than 120 V are not intended for U.S.A. and
Canada.
Operation at a voltage other than 120 V AC may require the use
of a different AC plug. Please contact either a local or foreign
Panasonic authorized service center for assistance in selecting
an alternate AC plug.
CAUTION:
The mains plug of the power supply cord shall remain readily
operable.
The AC receptacle (mains socket outlet) shall be installed near
the equipment and shall be easily accessible. To completely
disconnect this equipment from the AC mains, disconnect the
power cord plug from the AC receptacle.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
Do not pick up and move the unit while the tripod is attached.
The fitting may break under the weight of the tripod, which may
result in injury.
CAUTION:
Naked flame sources, such as lighted candles, should not be
placed on the apparatus.
indicates safety information.
2

FCC NOTICE (USA)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
CAUTION:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions and the user must use only shielded interface
cables when connecting to host computer or peripheral devices. Also, any unauthorized changes or modifications to this equipment could void
the user’s authority to operate this device.
NOTIFICATION (Canada)
CAN ICES-3 (A)/NMB-3(A)
indicates safety information.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord form being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
2 3
Read this first! (For AW‑HN130WPC, AW‑HN130KPC) (continued)

Read this first! (For AW‑HN130WE, AW‑HN130KE)
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws and drop-prevention wire mounting screw out of the
reach of infants and small children.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
The mains plug of the power supply cord shall remain readily
operable.
The AC receptacle (mains socket outlet) shall be installed near
the equipment and shall be easily accessible. To completely
disconnect this equipment from the AC mains, disconnect the
power cord plug from the AC receptacle.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
Do not pick up and move the unit while the tripod is attached.
The fitting may break under the weight of the tripod, which may
result in injury.
CAUTION:
Naked flame sources, such as lighted candles, should not be
placed on the apparatus.
indicates safety information.
Turkey Only
AEEE Yönetmeliğine Uygundur.
AEEE Complies with Directive of Turkey.
4

EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Pre‑requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting cables
• The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment to be connected to the
apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications, for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended for analog video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission applications, for analog audio signals.
• Other connecting cables (IEEE1394, USB)
Use double shielded cables, which provide quality performance for high-frequency applications, as connecting cables.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this manual.
2. Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by these standards.
However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an area where strong
electromagnetic fields are generated (by the presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverse
effects of the interference on the apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being
affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other appliances.
4 5
Read this first! (For AW‑HN130WE, AW‑HN130KE) (continued)

Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. and the other one is only for U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.
FOR U.K. ONLY
If the plug supplied is not suitable for your socket outlet, it should be
cut off and appropriate one fitted.
FOR U.K. ONLY
This appliance is supplied with a moulded three pin mains plug for
your safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amps and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure that it
is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
How to replace the fuse
1. Open the fuse compartment with a screwdriver.
Or
2. Replace the fuse.
Or Fuse
Fuse
indicates safety information.
Інформація для покупця
Виробник: Panasonic Corporation Панасонік Корпорейшн
Адреса виробника: Kadoma, Osaka, Japan Кадома, Осака, Японія
Країна походження: Japan Японія
Імпортер: ТОВ "ПАНАСОНІК УКРАЇНА ЛТД"
Адреса імпортера: провулок Охтирський, будинок 7, місто Київ, 03022, Україна
Примітки:
Термін служби виробу 7 років
Дата виготовлення може бути визначена за допомогою комбінації літер та цифр серійного номера, розташованого на продукті.
Приклад: X X XXXXXXX
Рік: остання цифра року (7 – 2017, 8 – 2018,…0 – 2020)
Місяць: А – Січень, В – Лютий… L – Грудень
Manufactured by: Panasonic Corporation,Osaka, Japan
Importer’s name and address of pursuant to EU rules:
Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
6
Read this first! (For AW‑HN130WE, AW‑HN130KE) (continued)

Read this first!
Note on grounding
• Ground the unit via the <SIGNAL GND> ground connector.
Ground connector
to ground
connector on wall
outlet, ground
bar, etc.
 Trademarks and registered trademarks
• Microsoft®, Windows®, Windows®7, Windows®8, Windows®8.1,
Internet Explorer®, ActiveX®and DirectX®are either registered
trademarks or trademarks of Microsoft Corporation in the United
States and other countries.
• Apple, Mac, OS X, iPhone, iPod Touch, iPad, and Safari are
registered trademarks of Apple Inc., in the United States and other
countries.
• Android™ is a trademark of Google Inc.
• Intel®and Intel®Core™ are trademarks or registered trademarks
of Intel Corporation in the United States and other countries.
• Adobe®and Reader®are either registered trademarks or
trademarks of Adobe Systems Incorporated in the United States
and/or other countries.
• The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other
countries.
• Other names of companies and products contained in these
Operating Instructions may be trademarks or registered
trademarks of their respective owners.
 About copyright and licence
Distributing, copying, disassembling, reverse compiling, reverse
engineering, and also exporting in violation of export laws of the
software provided with this unit are expressly prohibited.
 Abbreviations
The following abbreviations are used in this manual.
• Microsoft®Windows®7 Professional SP1 32/64-bit is abbreviated
to “Windows 7”.
• Microsoft®Windows®8 Pro 32/64-bit is abbreviated to “Windows
8”.
• Microsoft®Windows®8.1 Pro 32/64-bit is abbreviated to “Windows
8.1”.
• Windows®Internet Explorer®8.0, Windows®Internet Explorer®
9.0, Windows®Internet Explorer®10.0 and Windows®Internet
Explorer®11.0 are abbreviated to “Internet Explorer”.
For the purposes of this manual, the model numbers of the units are
given as listed in the table below.
Model number of unit Model number given in
manual
AW-HN130WPC
AW‑HN130
AW-HN130KPC
AW-HN130WE
AW-HN130KE
AW-HS50N AW‑HS50
AW-HS50E
AW-RP50N AW‑RP50
AW-RP50E
AW-RP120G AW‑RP120
AK-HRP200G AK‑HRP200
 Illustrations and screen displays featured
in the manual
• What is shown in the manual’s illustrations and screen displays
may differ from how it is actually appears.
• Functions which can be used by Windows only are indicated using
the mark.
• The screenshots are used in accordance with the guidelines of
Microsoft Corporation.
6 7

Contents
Read this first! (For AW‑HN130WPC, AW‑HN130KPC) ...................... 2
Read this first! (For AW‑HN130WE, AW‑HN130KE)............................ 4
Read this first! ...................................................................................... 7
Note on grounding ............................................................................... 7
Before use.............................................................................................. 9
Overview.............................................................................................. 9
Computer requirements ....................................................................... 9
Disclaimer of warranty ....................................................................... 10
Network security ................................................................................ 10
Features................................................................................................ 11
Controller supported........................................................................... 12
Accessories ......................................................................................... 13
Optional accessories .......................................................................... 13
Operating precautions ........................................................................ 14
Wireless remote control (optional accessory).................................. 16
Parts and their functions .................................................................... 17
Camera unit ....................................................................................... 17
Wireless remote control (not supplied) .............................................. 20
Setting the remote control IDs ........................................................... 22
Network settings.................................................................................. 23
Use the Easy IP Setup Software to establish the unit’s settings........ 23
Installing the plug-in viewer software................................................. 24
User authentication............................................................................ 24
Basic shooting operations ................................................................. 25
How to turn the power on and off ...................................................... 25
Turning the power on......................................................................... 25
Turning the power off......................................................................... 25
Selecting the units............................................................................... 26
Selecting the shooting modes (scene files)...................................... 27
Types of shooting modes................................................................... 27
How to select the shooting mode....................................................... 27
Shooting............................................................................................... 28
What to do when encountering problems in the basic shooting
operations ........................................................................................ 29
More advanced operations................................................................. 29
Manual shooting.................................................................................. 30
Manually adjusting the focus.............................................................. 30
Manually adjusting the iris.................................................................. 30
Manually adjusting the shutter speed ................................................ 30
Manually adjusting the gain ............................................................... 30
Preset memories.................................................................................. 31
White balance adjustment .................................................................. 32
Automatic adjustment (AWB: AWB A or AWB B) .............................. 32
Auto tracking white adjustment (ATW)............................................... 33
3200K and 5600K presets ................................................................. 33
VAR.................................................................................................... 33
Black balance adjustment .................................................................. 34
Automatic adjustment ........................................................................ 34
Black level (master pedestal) adjustment......................................... 35
Genlock adjustment ............................................................................ 36
Horizontal phase adjustment ............................................................. 36
Basic setup operations....................................................................... 37
When performing the operations using the wireless remote control ... 38
Operations on the AW-RP50 Remote Camera Controller ................. 39
Operations on the AW-RP120 Remote Camera Controller ............... 41
Operations on the AK-HRP200 Remote Operation Panel ................. 43
Camera menu items ............................................................................ 46
Setting the camera menu items ......................................................... 46
Top menu (Top Menu) screen ........................................................... 46
Camera screen .................................................................................. 47
Brightness 1/2 screen ........................................................................ 47
Brightness 2/2 screen ........................................................................ 48
Picture 1/3 screen.............................................................................. 49
Picture 2/3 screen.............................................................................. 49
Picture 3/3 screen.............................................................................. 50
Matrix 1/5 screen ............................................................................... 50
Matrix 2/5 screen ............................................................................... 51
Matrix 3/5 screen ............................................................................... 51
Matrix 4/5 screen ............................................................................... 52
Matrix 5/5 screen ............................................................................... 52
System screen ................................................................................... 53
Genlock screen.................................................................................. 53
Output screen .................................................................................... 54
Others 1/4 screen .............................................................................. 56
Others 2/4 screen .............................................................................. 56
Others 3/4 screen .............................................................................. 57
Others 4/4 screen .............................................................................. 57
Maintenance screen........................................................................... 58
Firmware VER 1/2 screen.................................................................. 58
Firmware VER 2/2 screen.................................................................. 58
IP Network screen.............................................................................. 59
Camera menu item table..................................................................... 60
Displaying the web screen ................................................................. 63
Displaying the web screen using a personal computer...................... 63
Switching between the Live screen [Live] and Web setup screen
[Setup] ........................................................................................... 64
Web screen operations....................................................................... 65
Live screen [Live] : Single display mode............................................ 65
Live screen [Live] : Multi display mode .............................................. 69
Web screen configurations ................................................................ 70
Logging into the Web setup screen [Setup]....................................... 70
Web setup screen [Setup].................................................................. 70
Basic screen [Basic]........................................................................... 71
Image screen [Image] ........................................................................ 72
Multi screen setup screen [Multi-Screen setup]................................. 86
User management screen [User mng.].............................................. 87
Network setup screen [Network]........................................................ 89
Maintenance screen [Maintenance]................................................. 101
Displaying the web screen using a mobile terminal ...................... 104
System log displays.......................................................................... 108
Limiters............................................................................................... 109
Setting/releasing the limiters ........................................................... 110
Setting/releasing the limiters............................................................ 110
Setting the limiters ........................................................................... 110
Releasing the limiters....................................................................... 110
Resetting the limiters ....................................................................... 110
Safe mode .......................................................................................... 111
Concerning the safe mode............................................................... 111
Detection of equipment trouble........................................................ 111
Troubleshooting ................................................................................ 112
Specifications .................................................................................... 121
Index ................................................................................................... 123
8

Before use
Overview
• This unit is a full HD camera with an integrated pan-tilt head that
features the newly developed 1/2.86-type full HD 3MOS sensor and
digital signal processor (DSP).
• In addition to its optical 20× zoom lens, the unit is equipped with
10× digital zoom to achieve vibrant high-quality images that have a
horizontal resolution of 1000 lines.
With its high sensitivity and built-in image-shake correction and night-
mode functions, the unit can record in a wide range of environments.
• This product is compatible with NDI|HX technology of NewTek, Inc.
• The unit supports transmission of video to NewTek NDI compatible
software applications and hardware devices over a network.
• When a controller is connected, camera operations can be performed
smoothly via IP control or serial control.
• The unit features a night mode that exposes subjects to infrared rays,
making it possible to shoot even under low-light conditions.
• When the unit is connected to a personal computer via an IP network,
it can be operated via a web browser.
• Equipped with a newly developed codec engine, the unit can output
Full HD images at up to 60 fps via a network.
• The unit supports standard serial communication formats, allowing
connection to commercially available controllers.
• Connection with a Panasonic camera controller is also possible via
Panasonic's proprietary serial communication format.
• The unit is available in white (AW-HN130WPC/AW-HN130WE) or
black (AW-HN130KPC/AW-HN130KE) to suit your intended application
and environment.
Computer requirements
CPU Intel®Core™ 2 DUO 2.4 GHz or more
recommended
Memory For Windows:
1 GB or more
(2 GB or more for 64-bit editions of Microsoft®
Windows®8.1, Microsoft®Windows®8, and
Microsoft®Windows®7)
For Mac:
2 GB or more
Network function 10BASE-T or 100BASE-TX port × 1
Image display Resolution: 1024 × 768 pixels or more
Color generation: True Color 24-bit or more
Supported operating
systems and
web browsers
For Windows:
Microsoft®Windows®8.1 Pro 64-bit / 32-bit *1
Windows®Internet Explorer®11.0*1*3
Microsoft®Windows®8 Pro 64-bit / 32-bit *1
Windows®Internet Explorer®10.0*1*3
Microsoft®Windows®7 Professional SP1 64-bit
/ 32-bit *2
Windows®Internet Explorer®11.0 / 10.0 / 9.0
/ 8.0 *3
For Mac:
OS X 10.9
Safari 7.0.2
OS X 10.8
Safari 6.1.2
OS X 10.7
Safari 6.1.2
For iPhone, iPad, iPod touch:
iOS 7.1
Standard web browsers
For Android:
Android OS
Standard web browsers
Other Adobe®Reader®
(for viewing the operating instructions available on
the website)
*1Use the desktop version of Internet Explorer. (Internet Explorer for
Windows UI is not supported.)
*2Windows®XP compatibility mode is not supported.
*3The 64-bit version of Internet Explorer®is not supported.
8 9

IMPORTANT
• Failure to provide the required personal computer environment
may slow down the delineation of the images on the screen, make
it impossible for the web browser to work and cause other kinds of
problems.
<NOTE>
• Depending on the software version of the unit, an update may be
necessary.
• Use the desktop version of Internet Explorer. (Internet Explorer for
Windows UI is not supported.)
• For the latest information on compatible operating systems and web
browsers, visit the support desk at the following website.
http://pro-av.panasonic.net/
Disclaimer of warranty
IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY
PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR
REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
AANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION,
DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR
EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
BPERSONAL INJURY OR ANY DAMAGE CAUSED BY
INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE
USER;
CUNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION
OF THE PRODUCT BY THE USER;
DINCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES
ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE
INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
EANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,
OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM
COMBINED BY THE DEVICES OF THIRD PARTY;
FANY DEMANDS FOR COMPENSATION, CLAIMS, ETC.
OCCASIONED BY THE INFRINGEMENT OF PRIVACY BY
INDIVIDUALS OR ORGANIZATIONS WHOSE IMAGES WERE
SHOT BY THE USER BECAUSE THESE IMAGES (INCLUDING
THE RECORDINGS MADE) WERE MADE AVAILABLE BY THE
USER BECAUSE IN THE PUBLIC DOMAIN FOR SOME REASON
OR OTHER OR BECAUSE THE IMAGES ENDED UP BEING
USED FOR PURPOSES OTHER THAN THE ONE DESCRIBED
ABOVE;
GLOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
Network security
As the unit intended to be used while connected to a network, the
following security risks exist.
ALeakage or theft of information through the unit
BUnauthorized operation of the unit by persons with malicious intent
CInterference with or stoppage of the unit by persons with malicious
intent
It is your responsibility to take precautions, such as those described
below, to protect yourself against the above network security risks.
• Use the unit in a network secured by a firewall, etc.
• If the unit is connected to a network that includes personal computers,
make sure that the system is not infected by computer viruses or other
malicious programs (using a regularly updated antivirus program, anti-
spyware program, etc.).
• Protect your network against unauthorized access by restricting users
to those who log in with an authorized user name and password.
• After accessing the unit as an administrator, be sure to close all web
browsers.
• Change the administrator password periodically.
• Restrict access to the unit by authenticating the users, for example,
to prevent setting information stored on the unit from leaking over the
network.
• Do not install the unit in locations where the unit, cables, and other
parts can be easily damaged or destroyed by persons with malicious
intent.
• Avoid connections that use public lines.
<NOTE>
Notes on user authentication
• User authentication on the unit can performed via digest authentication
or basic authentication. If basic authentication is used without the use
of a dedicated authentication device, password leaks may occur.
We recommend using digest authentication or host authentication.
Usage restrictions
• We recommend connecting the unit, controller, and any computers to
the same network segment.
Events based on settings inherent to the network devices, for example,
may occur in connections that include different segments, so be sure
to perform checks prior to operation.
10
Before use (continued)

 Multi‑format support
• You can switch between the following formats via the camera
menus or a web browser.
Supported formats:
1080/59.94p, 1080/29.97p*1, 1080/23.98p*2, 1080/59.94i,
1080/29.97PsF*2, 1080/23.98PsF, 720/59.94p, 480/59.94p
(HDMI) or 480/59.94i (SDI), 1080/50p, 1080/25p*1, 1080/50i,
1080/25PsF*3, 720/50p, 576/50p (HDMI), and 576/50i (SDI)
*1Native output
*2OVER 59.94i output (your monitor may recognize the signal as
59.94i).
*3OVER 50i output (your monitor may recognize the signal as 50i).
In terms of the VIDEO OUT signals, 480/59.94i or 576/50i signals
are output regardless of the format settings.
These signals can be used for monitoring purposes.
There is however a delay in the VIDEO OUT signal output by 120H
(HD lines) when at 720p and by 90H (HD lines) for any other.
• With the SD format, either "Squeeze", "LetterBox" or "SideCut"
can be selected.
 1/2.86-type MOS sensor and high-performance
20x zoom lens featured
• A newly developed 1/2.86-type full HD 3MOS sensor and DSP
(digital signal processor) are incorporated. High-quality pictures
are obtained by video processing in many different kinds of ways.
• In addition to its optical 20x zoom lens, the unit comes with a 10x
digital zoom to achieve high-quality images that overflow with
ambiance.
• A dynamic range stretcher (DRS) function that compensates for
overexposure and loss of dark detail and a digital noise reduction
(DNR) function for minimizing image lag even in dark locations
and shooting scenes clearly are incorporated to reproduce clean
and clear images in a wide range of applications.
 Easy operation of unit enabled by its
integration with a high‑performance pan‑tilt
head unit
• Operations at the high speed of 60°/s
• Wide rotational angles with a panning range of ±175° and a tilting
range from –30° to 210°
• Quiet operation with noise levels of NC35
• Storage of up to 100 positions in the preset memory
(The number of preset memories that can be used varies from one
controller to another.)
 Built‑in night mode
• The unit supports infrared shooting.
By exposing subjects to infrared rays, shooting under ordinarily
difficult low-light conditions is possible.
(Image output will be in black and white.)
• The iris will be fixed at open.
 IP image output functions
• The unit is equipped with image compression and IP transmission
LSI capabilities. Output in Full HD quality at up to 60 fps.
• Operation with IP control allows for a wide range of applications,
such as controlling the camera from remote locations.
 Standard serial communication support
• Connect up to seven cameras to a commercially available
controller via RS-232C interface.
 High degree of compatibility with Panasonic’s
currently available controllers, enabling a
flexible system to be put together
• A maximum of five units can be operated by serial control from
one of Panasonic’s currently available controllers (AW-RP120,
AW-RP50 and AK-HRP200).
The unit can also be used together with the cameras and pan-tilt
head unit systems currently available from Panasonic Corporation
so that an existing system can be used to advantage to put
together a system that is even more flexible.
<NOTE>
• It may be necessary to upgrade the version of the controller
in order to support the unit. For details on upgrading, visit the
support page on the following website.
http://pro-av.panasonic.net/
The maximum distances between the units and controller is
1000 meters (3280 ft). (when serial control is exercised)
Use of an external device or some other means must be
provided separately in order to extend the video signal
connections.
 Easy construction of systems thanks to
integrated design used for pan‑tilt head,
camera and lens
• By integrating the camera, lens and pan-tilt head into a single unit,
it is now easier to construct systems.

Use of easy‑to‑operate wireless remote control
(optional accessory) is possible
• A wireless remote control capable of operating up to four units can
be used.
It can easily be used to set the various functions or switch
between them while viewing the menu screens.
 Flexible camera layout enabled by simple
connection and installation
• This unit features excellent connectivity and installability thanks
to the IP control; a lightweight main unit, and the turn-lock
mechanism, which enables the user to install it on his or her own
(only when used indoors).
<NOTE>
• Bear in mind that this unit is designed to be used indoors only:
It cannot be used outdoors.
 Increased functionality with the same compact
size and weight of previous models
• A wide range of features have been added while maintaining the
compact size, weight, and footprint of previous models of the unit.
 Easy connections and settings courtesy of IP
control
• Up to a hundred units can be operated by IP connection from a
Panasonic controller (AW-RP120, AW-RP50, AK-HRP200).
(The maximum length of the LAN cables is 100 meters (328 ft).)
 PoE+ *4eliminates need for camera power
configurations
• Configurations for camera's power supply are not necessary when
the unit is connected to a network device that supports the PoE+
standard (IEEE802.3at compliant)*5.
<NOTE>
• When using a PoE+ device that requires software authentication,
it may take a few minutes after power supply starts before the unit
is operational.
• If the AC adaptor and a PoE+ power supply are connected
simultaneously, the AC adaptor will have priority. If the AC adaptor
is disconnected while both power supplies are connected, the unit
will restart automatically, and the image will be interrupted.
• Use a Category 5e cable or higher when using a PoE+ power
supply. The maximum length of the cable between the power
supply unit and the unit is 100 meters (328 ft). Using a cable that
is lower than Category 5 may result in reduced power supply
capabilities.
• When a PoE+ injector is connected to a personal computer that
supports Gigabit Ethernet using a straight LAN cable, the personal
computer may not recognize the injector in rare cases. In such
cases, connect the personal computer to the unit using a cross
LAN cable (or via cross connection).
*4Power over Ethernet Plus. Referred to as "PoE+" in this
manual.
*5For details on PoE+ power supply devices for which operation
has been verified, consult your local dealer.
Features
10 11

z AW‑RP120
z AW‑RP50
z AK‑HRP200
• It may be necessary to upgrade the version of the controller in order to support the unit.
For details on upgrading, visit the support page on the following website.
http://pro‑av.panasonic.net/
<NOTE>
• The following operations can not be performed via the following controllers.
Item AW‑RP555 AW‑RP655
Camera OSD menu operation Supported Supported
Scene Supported *1
(1/2/3/USER)
Supported
(HALOGEN/FLUORESCENT/OUTDOOR/USER)
Iris Mode Supported Supported
Shutter Mode Supported with some restrictions *2
(Step only) Not supported
Gain Supported *1Supported with some restrictions *3
ND Filter Not supported Not supported
Day/Night Supported with some restrictions *4Supported with some restrictions *4
White Balance Mode Supported *1
(AWB A/AWB B/ATW only)
Supported
(AWB A/AWB B/ATW only)
AWB/ABB Supported Supported
Color Temperature Not supported Not supported
R Gain / B Gain Not supported Supported
Pedestal Not supported Supported
R Pedestal / B Pedestal Not supported Supported with some restrictions *5
Detail Not supported Not supported
V Detail Level Not supported Not supported
CAM/BAR Supported *1Supported
Pan Supported Supported
Tilt Supported Supported
Preset Supported Supported
Preset Speed Not supported Not supported
Preset Speed Table Not supported Not supported
Preset Scope Not supported Not supported
Freeze During Preset Not supported Not supported
Focus Mode Supported with some restrictions *4Supported with some restrictions *4
Zoom Supported Supported
Digital Extender Not supported Not supported
OIS Not supported Not supported
Tally Supported Supported
*1If the setting value is changed on another device, it may take some time for the setting value to be applied.
*2If the Shutter Mode is not turned off/on after configuration, the value will not be changed.
*3Improper operation will occur when Gain is set to 19 dB or higher.
*4If the setting value is changed on another device, the setting value will not be applied.
(If the value is configured locally on the device, the value will be applied.)
*5The value range display will be incorrect (-150 to +150).
Controller supported
12

Accessories
Check that the following accessories are present and accounted for.
• After removing the product from its container, dispose of the power cable cap (if supplied) and packing materials in an appropriate manner.
Mount bracket for installation surface
(Hanging / Desktop) (1)
Main unit mounting screw (with flat
washer, spring washer)
M3×6 mm (1)
AC adaptor (1)
Power cable
z AW-HN130WPC/AW-HN130KPC (1) z AW-HN130WE/AW-HN130KE (2 types)
(For areas other than the U.K.) (For the U.K.)
Drop‑prevention wire (1)
Drop‑prevention wire mounting screw (1)
(comes attached to the unit)
Bracket mounting screws (bind‑head)
M4×10 mm (4)
Cable cover (1)
Optional accessories
z Wireless remote controller AW‑RM50G (Size “AA” dry battery x 2, obtained separately)
z Direct ceiling mount bracket WV‑Q105A
12 13

 Shoot under the proper lighting conditions.
To produce pictures with eye-pleasing colors, shoot under the
proper lighting conditions.
The pictures may not appear with their proper colors when shooting
under fluorescent lights. Select the proper lighting as required.
 To ensure a stable performance in the long
term
Using the unit for prolonged periods in locations where the
temperature and humidity levels are high will cause its parts to
deteriorate, resulting in a reduction of its service life.
(Recommended temperature: Max. 35 °C (95 °F))
Ensure that a cooling unit or heating unit will not blow any air
directly toward the installation location.
 Do not point the camera at
strong lights.
When parts of the MOS sensor are
exposed to spotlights or other strong
lights, blooming (a phenomenon where
the edges of strong lights become
blurred) may occur.
Bright subject
Blooming
 What happens with high‑brightness subjects
Flare may occur if an extremely bright light source is pointed at
the lens. In a case like this, change the angle or take some other
remedial action.
 When using the automatic functions
• The initial settings have been set to auto for some of the items
of the scenes on the camera menus and other menus, making it
impossible for these items to be operated manually. To operate
them manually, switch from the auto settings to the manual
settings as required.
• When using the ATW (auto tracking white adjustment) function
under fluorescent lights, the white balance may vary.
• In some situations, it may be hard to focus at the auto setting. In
cases like this, select the manual setting, and focus manually.
 Zooming and focusing
When the focus is set manually, out-of-focusing may occur during
zooming.
After zooming, if necessary, either adjust the focus or set the focus
to auto.
When using the focus at the manual setting, proceed with zooming
after setting the focus position at the Tele end where the focusing
accuracy is higher. (However, if the distance from the unit to the
subject is less than 1.5 meters (4.92 ft), the subject may shift out of
focus at the Wide end.)
If zooming is performed to the Tele end after having adjusted the
focus at the Wide end, out-of-focusing may occur.
 Operation of the lens when the power is turned
on
When the unit’s power is turned on, the zoom, focus and iris are
adjusted automatically.
 The unit comes with the safe mode.
The safe mode is function designed to protect the unit from damage.
For further details, refer to “Concerning the safe mode” (→ page 111).
 Operating temperature range
Avoid using the unit in cold locations where the temperature drops
below 0 °C (32 °F) or hot locations where the temperature rises
above 40 °C (104 °F) since these temperatures downgrade the
picture quality and adversely affect the internal parts.
 Concerning the VIDEO OUT signal
The VIDEO OUT signal is provided in case the images are to be
monitored.
 Concerning the HDMI interface standard
This unit has been certified as HDMI-compatible, but on rare
occasions images may not be displayed depending on the HDMI
device which has been connected to the unit.
 Color bars
• Color bars are used to adjust the color phase, and the widths and
positions of these bars may differ from other models.
• The setting for the Down CONV. Mode item when color bars are
displayed is fixed at “Squeeze”.
 Concerning the IP video frame rates
The IP video frame rate may be slower depending on the network
environment, performance of your personal computer or mobile
terminal, subject of the video, and access volume.
 H.264 patent pool licensing
This product is licensed based on the AVC Patent Portfolio License,
and the license does not extend beyond uses by users, who engage
in the acts described below, for their own personal and non-profit
applications.
(i) Recording of image information in compliance with the AVC
standard (hereafter, “AVC videos”)
(ii) Playing of AVC videos recorded by consumers engaging
in personal activities or AVC videos acquired from licensed
providers
For details, visit MPEG LA, LLC website (http://www.mpegla.com).
 Concerning PoE+ power supply
The unit complies with the IEEE802.3at standard. Use a compatible
Ethernet hub and PoE+ injector to use a PoE+ power supply.
For details on Ethernet hubs and PoE+ injectors for which
operations have been verified, consult your local dealer.
 Turn off the power before connecting or
disconnecting the cables.
This unit is not equipped with a power switch.
Turn off the DC 12 V power supply or PoE+ power supply device
before connecting or disconnecting cables.
 Handle the unit carefully.
Do not drop the unit or subject it to strong impact or vibration.
Failure to obey may cause the unit to malfunction.
 When the unit is not in use
Turn off the unit’s power when it is not in use.
When the unit is no longer going to be used, do not leave it lying
around, but be absolutely sure to dispose of it properly.
 Do not touch the optical system parts.
The optical system parts are vital to the operation of the camera.
Under no circumstances must they be touched.
In the unlikely event that they have become dusty, remove the
dust by using a camera blower or by wiping them gently with a lens
cleaning paper.
 Do not point the camera directly at the sun or a
laser beam no matter whether it is turned on or
not.
Taking images of the sun, laser beams, or other brightly lit subjects
for prolonged periods of time may damage the CCD.
 Personal computer used
If the same image is displayed for a prolonged period on a Personal
computer's monitor, the monitor may be damaged. Use of a screen
saver is recommended.
 Concerning the IP address setting
Do not run the Easy IP Setup Software on a multiple number of
personal computers for a single camera and set the IP address at
the same time.
Otherwise, you will be unable to complete the proper procedure and
set the IP address correctly.
Operating precautions
14

 Do not allow foreign matter to make contact
with the rotating parts.
Failure to obey may cause the unit to malfunction.
 Do not get close to the moving parts of the
camera head.
Do not put your fingers or body close to the unit while it is in
operation. Doing so may result in injury or cause the unit to
malfunction.
Furthermore, if the unit hits a person or obstacle, during the panning
or tilting operation, the unit will enter into the safe mode.
For further details, refer to page 111.
 Keep the unit away from water.
Avoid all direct contact with water. Failure to obey may cause the
unit to malfunction.
 Maintenance
Turn off the unit’s power before proceeding with maintenance.
Failure to obey may result in injuries.
Wipe the surfaces using a soft dry cloth. Avoid all contact with
benzine, paint thinners and other volatile substances, and avoid
using these substances. Otherwise, the casing may become
discolored.
 Do not turn the camera head by hand.
Turning the camera head by hand may cause the unit to
malfunction.
 Use the unit in an environment with minimal
moisture and dust.
Avoid using the unit in an environment with high concentration of
moisture or dust since these conditions will damage the internal
parts.
 Disposal of the unit
When the unit has reached the end of its service life and is to be
disposed of, ask a qualified contractor to dispose of the unit properly
in order to protect the environment.
 Information on software used with this product
This product includes GNU General Public License (GPL) and GNU Lesser General Public License (LGPL) licensed software, and the customer is
entitled to obtain, modify, or redistribute the source code for the software.
This product includes MIT Licensed software.
This product includes BSD Licensed software.
For details on obtaining the source codes, visit the following website.
http://pro-av.panasonic.net/
However, do not contact Panasonic for questions regarding obtained source codes.
14 15
Operating precautions (continued)

This unit can be operated by remote control using a wireless
remote control (model number: AW‑RM50G) purchased separately.
Check out the following points before using the wireless remote
control.
z Point the wireless remote control at the unit’s wireless
remote control signal light‑sensing area (front panel or
back panel), and operate it within a range of 10 meters
(32.8 ft) from these areas.
z Refer to “Layout of wireless remote control signal
light‑sensing areas” on the right.
z The signal sensing distance is reduced if the angle at
which the wireless remote control signals are sensed is
increased.
The light-sensing sensitivity is reduced to about one-half when the
wireless remote control is pointed at an angle of 40 degrees from
each position in front of a wireless remote control signal light-sensing
area (front panel or back panel).
If the remote control is operated from the behind the unit, it may be
either difficult or impossible to perform the desired operations.
z If the unit is installed near fluorescent lights, plasma
monitors or other such products or if the unit is
exposed to sunlight, the effects of the light may make it
impossible for the unit to be operated using the wireless
remote control.
Be sure to follow the steps below for installation and use.
• Take steps to ensure that the wireless remote control signal light-
sensing area will not be exposed to the light from fluorescent lights,
plasma monitors or other such products or from the sun.
• Install the unit away from fluorescent lights, plasma monitors and
other such products.
z For about 10 minutes even after the batteries have been
removed from the wireless remote control, the selection
of the operation to be performed (the <CAM1>, <CAM2>,
<CAM3> or <CAM4> button which was pressed last) will
remain stored in the memory.
When a longer period of time elapses, however, the
selection is reset to the status established when the
<CAM1> button was pressed.
<Layout of wireless remote control signal light‑sensing areas>
<NOTE>
• The arrows in the figure below show the light-sensing directions in
which the wireless remote control signals travel.
Wireless remote control
signal light‑sensing area
(back panel, 1 place)
Wireless remote
control signal light‑
sensing area (front
panel, 2 places)
• Top view
• Rear panel view
Approx. 45° Approx. 45°
Wireless remote control (optional accessory)
16

1
2
5
7
4
3
6
4
8
3
25 24
16 22 18
9 101321 15 23 1417
11 12 2019 21
Rear panel
Bottom panel
1. Mount bracket for installation surface (supplied
accessory)
Mount this bracket onto the installation surface, and then attach the
camera main unit to the bracket.
2. Drop‑prevention wire
This wire is screwed down to the bottom panel of the camera main
unit. Loop the circle part of the wire around the hook of the mount
bracket.
3. Hole for securing the camera pedestal
This hole is provided in the bottom panel of the camera pedestal.
4. Wireless remote control signal light‑sensing area
The light-sensing area is provided in three places, on the front panel
of the camera pedestal and at the top of the rear panel.
5. Status display lamp
This lights in the following way depending on the status of the unit.
Orange: When the standby status is established
Green: When the power is on
Red: When trouble has occurred in the unit
Green and blinks twice:
When a signal matched by the remote control ID has
been received from the wireless remote control (optional
accessory) while the power is on
Orange and blinks twice:
When a signal not matched by the remote control ID has
been received from the wireless remote control (optional
accessory) while the power is on
6. Camera head
This rotates in the up and down direction.
7. Tilt head
This rotates in the right and left direction.
8. Tally lamp
This comes on or goes off in response to the control from the
controller but only when “On” has been selected as the tally lamp use
setting.
9. RS‑422 connector <RS‑422>
This RS-422 connector (RJ45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
The tally lamp can be lit by shorting the TALLY signal (pin 2) with
GND (pin 1).
<NOTE>
• Do not apply a voltage to the TALLY signal pin.
LAN cable*1(category 5 or above, straight cable), max. 1000 m
(3280 ft)
*
1
Use of an STP (shielded twisted pair) cable is recommended.
Pin
No. Signal Pin No. Signal
1 GND 5 TXD+
2 TALLY 6 RXD+
3 RXD– 7 —
4 TXD– 8 —
Parts and their functions
Camera unit
16 17

10.RS‑232C connectors <RS‑232C IN/OUT>
Connects to an RS-232C cable.
RS-232C IN/OUT
connector appearance
12
3
4
5
6
7
8
Mini Din 8-pin (JST)
RS‑232C IN RS‑232C OUT
Pin
No. Signal Pin No. Signal
1 DTR_IN 1 DTR_OUT
2 DSR_IN 2 DSR_OUT
3 TXD_IN 3 TXD_OUT
4 GND 4 GND
5 RXD_IN 5 RXD_OUT
6 GND 6 GND
7 IR OUT R 7 NC
8 IR OUT L 8 NC
<NOTE>
• Be aware that the polarities (+/-) of the serial data may be different
depending on the specifications of the device to be connected.
11.LAN connector for IP control <LINK/ACT>
This LAN connector (RJ45) is connected when exercising IP control
over the unit from an external device. Use a cable with the following
specifications for the connection to this connector.
When using a PoE+ Ethernet hub
LAN cable*1(category 5e or above, straight cable),
max. 100 m (328 ft)
When not using a PoE+ Ethernet hub
LAN cable*1(category 5 or above, straight cable),
max. 100 m (328 ft)
*1Use of an STP (shielded twisted pair) cable is recommended.
12.HDMI connector <HDMI>
This is the HDMI video output connector.
13.Anti‑theft wire mounting hole
The anti-theft wire bracket (available from a hardware store) is
attached here.
14.G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Format External sync signal input format
BBS Tri‑level sync
1080/59.94p
1080/29.97p
1080/23.98p
1080/59.94i
1080/29.97PsF
1080/23.98PsF
720/59.94p
480/59.94p(i)
480/59.94i
480/59.94i
480/59.94i
480/59.94i
480/59.94i
—
480/59.94i
480/59.94i
1080/59.94i
—
1080/59.94i
1080/59.94i
1080/59.94i
1080/23.98PsF
720/59.94p
—
1080/50p
1080/25p
1080/50i
1080/25PsF
720/50p
576/50p(i)
576/50i
576/50i
576/50i
576/50i
576/50i
576/50i
1080/50i
—
1080/50i
1080/50i
720/50p
―
<NOTE>
• Locking to a subcarrier is not possible with BBS.
15.VIDEO OUT connector <VIDEO OUT>
This is the output connector used for monitoring the camera’s
composite video signals. Use the monitor in the internal
synchronization mode.
Provide a BNC coaxial cable as the connecting cable.
There is a delay in the VIDEO OUT signal output by 120H (HD lines)
when at 720p and by 90H (HD lines) for any other.
16.Hole used to secure cable cover
Use the screw provided to secure the cable cover.
17. SDI OUT connector <SDI OUT>
This is the SDI video signal output connector.
18. DC IN connector <12V IN >
Connect the AC adaptor supplied with the unit to this connector to
supply the DC 12 V voltage to the unit.
19.Cable clamp
This is used to hold the cable connection to the DC IN connector and
prevent it from becoming disconnected.
20.IR ID switches <IR ID>
CAM1 CAM2 CAM3 CAM4
These are used to select the ID of the wireless remote control
(optional accessory).
The IR ID switch settings “CAM1” to “CAM4” correspond to the
<CAM1> to <CAM4> buttons on the wireless remote control.
21.Square holes (X2) for cable cover tabs
The tabs on the two sides of the cable cover are fitted into these
holes.
22.AUDIO IN connector <AUDIO IN>
Inputs external audio (microphone, line).
23.Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. “Note on grounding” (→ page 7)
24.Tripod screw holes
(Screw: 1/4‑20 UNC, ISO 1222 (6.35 mm))
Use these screw holes when securing the unit to a tripod, etc.
25.Service switches
SW1
ON
OFF
SW2 SW3 SW4 SW5 SW6 SW7 SW8
Function OFF ON Factory
settings
SW1 Camera
address setting
(standard serial
communication)
See descriptions for SW1 to SW3 OFF
SW2 OFF
SW3 OFF
SW4 Communication
format
Panasonic
proprietary serial
communication
Standard serial
communication
OFF
SW5 Always leave at OFF (used for factory adjustments) OFF
SW6 Infrared output Disable Enable OFF
SW7 Communication
baud rate
9600 bps 38400 bps OFF
SW8 Communication
connector
RS-422 RS-232C OFF
<NOTE>
• Perform switch settings before turning the unit on.
• Cameras whose camera address setting switches are set to AUTO
cannot coexist with cameras whose switches are set to 1 to 7.
• Manually setting multiple cameras to the same address will not
allow you to control multiple cameras from a single controller
simultaneously.
18
Parts and their functions (continued)

Service switch settings
SW1 to SW3 (camera address setting switches)
Configure the camera address.
Set this to AUTO under normal circumstances. When cameras are set
to AUTO, addresses will be assigned to the cameras automatically
in response operation from the controller in the order in which the
cameras were connected.
To manually configure the address, set the switches as follows.
Address AUTO 1 2 3 4 5 6 7
SW1 OFF ON OFF ON OFF ON OFF ON
SW2 OFF ON ON OFF OFF ON ON OFF
SW3 OFF ON ON ON ON OFF OFF OFF
SW4 (communication format selection switch)
Selects the communication format.
When this is set to ON, standard serial communication is enabled.
When this is set to OFF, Panasonic's proprietary serial
communication is enabled.
SW5 (maintenance switch)
Fixed at OFF.
Do not change this switch setting.
SW6 (infrared output switch)
When this is set to ON, infrared output is enabled. The signal received
via the remote control sensor is output from pins 7 and 8 of the <RS-
232C IN> connector.
Signal output is disabled when this is set to OFF.
SW7 (communication baud rate switch)
When this is set to ON, the baud rate is 38400 bps.
When this is set to OFF, the baud rate is 9600 bps.
SW8 (communication connector switch)
When this is set to ON, the RS-232C is enabled.
When this is set to OFF, the RS-422 is enabled.
 Simultaneous output conditions for each video
format
z SDI/HDMI/VIDEO output
Format SDI
output
HDMI
output
VIDEO
output*4
HD/SDI 1080/59.94p   
1080/50p   
1080/59.94i   
1080/50i   
1080/29.97PsF *1
1080/25PsF *2
1080/23.98PsF  
1080/29.97p*3  
1080/25p*3  
1080/23.98p *1 
720/59.94p   
720/50p   
SD/SDI 480/59.94p 
576/50p 
480/59.94i  
576/50i  
*1OVER 59.94i output (your monitor may recognize the signal as
59.94i).
*2OVER 50i output (your monitor may recognize the signal as 50i).
*3Native output
*4480/59.94i and 576/50i is output to the VIDEO output regardless of
the format setting.
z IP video transmission output (1‑/multi‑channel display)
1‑channel display
Resolution 1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90
(non-dependent on SYS format)
Frame
rate
59.94Hz 1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/
60 fps*1
50Hz 1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps*2
*160 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
*250 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
Multi‑channel display
Setting H.264 CH1 H.264 CH2 H.264
CH3/CH4
JPEG
CH1/CH2/
CH3*3
Resolution 1920×1080
1280×720
1920×1080
1280×720
640×360
320×180
160×90
1280×720
640×360
320×180
160×90
1920×1080
1280×720
640×360
320×180
160×90
Frame
rate
59.94Hz 60fps 5 fps
15 fps
30 fps
5 fps
15 fps
30 fps
1 fps
2 fps
3 fps
5 fps
6 fps
10 fps
15 fps
30 fps
50Hz 50 fps 5 fps
12.5 fps
25 fps
5 fps
12.5 fps
25 fps
1 fps
2 fps
5 fps
10 fps
12.5 fps
25 fps
*3Different resolutions must be specified for JPEG CH1 / CH2 / CH3.
18 19
Parts and their functions (continued)

13
14
15
17
21
19
22
20
16
4
5
6
7
8
9
10
11
18
12
13
2
1. ON/STANDBY button <ON/STANDBY>
Each time this is pressed for 2 seconds, operation switches between
turning on the unit’s power and establishing the standby status.
2. Signal transmission window
3. MENU button <MENU>
Each time this is pressed for 2 seconds, operation switches between
displaying the unit’s camera menu and exiting the camera menu.
When it is pressed quickly (for less than 2 seconds) while a camera
menu is displayed, the setting change is canceled.
Furthermore, the pan and tilt movement range limits (limiters) are set
and released by operating the <PRESET/LIMIT> button and the pan/
tilt buttons (<4> <5> <b> <a>).
For details, refer to “Setting/releasing the limiters” (→ page 110).
4. CAM1 to CAM4 buttons
<CAM1> <CAM2> <CAM3> <CAM4>
Selects a camera to be operated.
Once a button has been selected, the unit corresponding to the
selected button can be operated.
5. SET button <SET>
If this button is held down for 2 seconds when the AWB A memory or
AWB B memory has been selected for the white balance adjustment,
the black balance and white balance are adjusted automatically and
registered in the memory selected.
When this button is pressed for under 2 seconds, only the white
balance is adjusted automatically.
6. MODE button <MODE>
This is used to select the video signals which are output from the unit.
Each time it is pressed, the signals are switched between the color
bar signals and camera video signals.
<NOTE>
• The setting for the [Down CONV. Mode] item when color bars are
displayed is fixed at [Squeeze].
• When [Audio] is set to [On] and the color bar is displayed, a test
sound (1 kHz) is output. Be cautious of the volume on external
devices.
7. GAIN button <OFF> <LOW> <HI> <AUTO>
These are used to set the gain.
The gain increase can be set in three steps using the <OFF>, <LOW>
and <HI> buttons.
<LOW> is set to 9 dB, and <HI> is set to 18 dB.
When the <AUTO> button is pressed, the AGC function is activated,
and the gain is adjusted automatically depending on the light quantity.
The maximum gain of the AGC function can be set using the camera
menu.
8. Preset memory call buttons <1> to <12>
These are used to call the information on the unit’s directions and
other settings, which have been registered in the unit’s preset
memories No.1 to No.12, and reproduce those settings.
Settings in preset memories No.13 and above cannot be called from
the wireless remote control.
9. PRESET/LIMIT button <PRESET/LIMIT>
This is used to register the settings in the preset memories or set or
release the limiters.
When a preset memory call button is pressed while the <PRESET/
LIMIT> button is held down, the information on the unit’s current
direction and other settings is registered in the call button.
Preset memory call buttons <1> to <12> correspond to the unit’s No.1
to No.12 preset memories.
Furthermore, the pan and tilt movement range limits (limiters) are set
and released by operating the <PRESET/LIMIT> button, <MENU>
button and the pan/tilt buttons (<4> <5> <b> <a>).
For details, refer to “Setting/releasing the limiters” (→ page 110).
10.Pan‑tilt buttons and menu operation buttons
<4> <5> <b> <a> <M>
1) These are used to change the unit’s direction.
The unit is tilted in the up/down direction using the <4> and <5>
buttons and panned in the left/right direction using the <b> and
<a> buttons.
The <M> button does not work during tilting and panning.
When the <4> or <5> and <b> or <a> buttons are pressed at the
same time, the unit moves diagonally.
2) The buttons are used for menu operations when the unit displays
the camera menus.
Use the <4> , <5> (<b>, <a>) buttons to select the menu items.
When a selected item has a sub-menu, the sub-menu will be
displayed by pressing the <M> button.
When the cursor is aligned with a particular item and the <M>
button is pressed on the setting menu at the bottom hierarchical
level, the setting of the selected item blinks.
When the <M> button is pressed after the setting has been
changed using the <4> and <5> (<b> and <a>) buttons, the
setting stops blinking, and the new setting is entered.
A setting for a regular menu item is reflected immediately if it is
changed while it is still flashing.
If the <MENU> button is pressed quickly (for less than 2 seconds)
while the setting is in the blinking status, the change will be
canceled, and the setting selected prior to the change will be
restored.
Wireless remote control (not supplied)
20
Parts and their functions (continued)