Panasonic DMR-EA18K User manual

Basic Operations
P13
Operating Instructions
DVD Recorder
Model No. DMR-EA18
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Before connecting, operating or adjusting this product, please read the instructions completely.
Please keep this manual for future reference.
Region number supported by this unit
Region numbers are allocated to DVD players and DVD-Video according to where they are sold.
The region number of this unit is “1”.
The unit will play DVDs marked with labels containing “1” or “ALL”.
•
•
Example:
1ALL 24
1
If you have any questions contact
1-800-211-PANA(7262)
The warranty can be found on page 71.
La referencia rápida en español se encuentra en la página 72-75.
PRQT9048-P

2
RQT9048
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE,
DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE,
DRIPPING OR SPLASHING AND THAT NO OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE
PLACED ON THE APPARATUS.
USE ONLY THE RECOMMENDED ACCESSORIES.
DO NOT REMOVE THE COVER (OR BACK); THERE
ARE NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
•
•
•
CAUTION!
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE,
BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT
RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
The socket outlet shall be installed near the equipment and
easily accessible. The mains plug of the power supply cord shall
remain readily operable. To completely disconnect this apparatus
from the AC Mains, disconnect the power supply cord plug from
AC receptacle.
FCC Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution: To assure continued compliance, follow the
attached installation instructions and use only shielded interface
cables when connecting to peripheral devices.
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Declaration of Conformity
Trade Name: Panasonic
Model No.: DMR-EA18
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-7262
•
•
•
•
(Inside of product)
Precautions

3
Getting Started
RQT9048
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions
listed below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Unit Care
The precision parts in the unit are readily affected by the
environment, especially temperature, humidity, and dust.
Cigarette smoke also can cause malfunction or breakdown.
Do not place the unit on
amplifiers or equipment
that may become hot.
The heat can damage the unit.
Do not place any heavy
objects on top of the unit.
•
•
The unit should not be mounted in a vertical position. It’s designed
to operate in the horizontal position.
Before moving the unit, ensure the disc tray is empty.
Failure to do so will risk severely damaging the disc and the unit.
•
•
■Cautions about condensation
Condensation can cause unreliable playback of recordings.
Condensation may form in the following cases,
The unit is brought from cold surroundings into a well-heated room.
The unit is suddenly brought from cool surroundings, such as an
airconditioned room or car, to a place which is hot and humid.
During rainy seasons.
In any of the above-mentioned conditions, do not operate the unit for
at least 2 hours. The unit is not equipped with a moisture sensor.
•
•
•
■Maintenance
To clean the unit
Wipe with a soft, dry cloth.
Never use alcohol, thinner or benzine to clean the unit.
Before using chemically treated cloth, carefully read the instructions
that came with the cloth.
To clean the DVD lens
Dust and dirt may adhere to the unit’s lens over time, possibly making
it impossible to record or play discs.
Use the DVD lens cleaner about once every year, depending on
frequency of use and the operating environment.
Carefully read the lens cleaner’s instructions before use.
DVD lens cleaner: RP-CL720PP
•
•
■ When the unit is not to be used for a long time
To save power, unplug the AC power supply cord from the household AC outlet. This unit consumes a small amount of power, even when it is
turned off.
Standby power consumption
Front Display (➔47)
Automatic Bright
Quick Start (➔43) On Approx. 9.8 W Approx. 9.8 W
Off Approx. 0.6 W Approx. 2.1 W

4
RQT9048
Table of Contents, Accessories
Getting Started
Precautions.............................................................................2
IMPORTANT SAFETY INSTRUCTIONS ................................3
Unit Care ......................................................................................3
Accessories..................................................................................5
Remote Control Information .........................................................5
Control Reference Guide........................................................6
Main Unit ......................................................................................6
Remote Control ............................................................................6
Rear Panel ...................................................................................7
The Unit’s Display ........................................................................7
Media Handling.......................................................................7
Inserting Discs .............................................................................7
Inserting an SD Card ...................................................................7
Inserting USB memory.................................................................7
Basic Connection....................................................................8
Connecting to a Television and a Set Top Box .............................8
Connecting to a TV with an HDMI (High Definition Multimedia
Interface) Cable........................................................................9
Setting the Set Top Box Control and Clock...........................10
Acquiring the setting information from the TV (VIERA) ..............12
Basic Operations
Playback ............................................................................ 13
Playing Discs ............................................................... 13
Recording Set Top Box Programs...................................... 14
Scheduled Recording ........................................................ 15
Deleting Recordings .......................................................... 16
Delete Navigator .......................................................... 16
Delete Recordings During Playback ............................ 16
Advanced Features
Important Notes for Recording ............................................17
Advanced Recording ............................................................18
Recording Modes and Estimated Disc Recording Time.............18
When the format confirmation screen is displayed.....................18
When removing a Recorded Disc ..............................................18
Specifying the Recording Time ..................................................19
Flexible Recording......................................................................19
Playing while you are recording .................................................19
Advanced Scheduled Recording ..........................................20
To cancel a scheduled recording in progress.............................20
Check, Change, or Delete Programs .........................................20
To release the unit from recording standby
(Before recording starts) ............................................................20
Recording from an External Device......................................21
Recording from a VCR or a Set top box equipped
with a Hard Drive, etc.................................................................21
Recording from a DV Camcorder ...............................................22
Advanced Playback ..............................................................23
Zoom in on video........................................................................23
Menu Screens on the TV............................................................23
Selecting Recordings to Play .....................................................23
Search........................................................................................23
Skip ............................................................................................23
Direct Play..................................................................................23
Quick View (Play x1.3) ...............................................................24
Slow-motion Play........................................................................24
Frame-by-Frame Viewing ...........................................................24
Time Slip ....................................................................................24
CM Skip......................................................................................24
Create Chapters.........................................................................24
Changing Audio during Playback ...............................................24
Playing MP3s........................................................................25
Playing Still Pictures (JPEG) ................................................26
Playing Playlists....................................................................28
Playlist Properties/View Chapters ..............................................28
Status Messages..................................................................28
Entering Text.........................................................................29
FUNCTIONS Window........................................................ 29
Linked Operations with the TV (VIERA Link™ “HDAVI Control™”) ... 30
Easy Control only with VIERA Remote Control....................... 31
Advanced Editing
Recordings-Editing ...............................................................32
Accessing the Recording View...................................................32
Editing Operations to Recordings ..............................................32
Still Pictures-Editing..............................................................34
Accessing the Album/Picture View.............................................34
Album/Picture Operations ..........................................................34
Deleting Still Pictures............................................................35
Delete Navigator ........................................................................35
Copying Still Pictures............................................................36
Copying Still Pictures via the Album View Screen......................36
Importing still pictures from an SD card or USB memory ..........36
Chapters-Creating, Editing ...................................................37
Accessing the Chapter View ......................................................37
Chapter Operations....................................................................37
Setting Menus
Setting On-Screen Menus ....................................................38
Accessing the On-Screen Menus...............................................38
DVD and Card Management ................................................39
Accessing the Management Menus ...........................................39
Setup Menus ........................................................................42
Set Top Box Control....................................................................42
Off Timer ....................................................................................43
Remote Control .......................................................................... 43
Clock Settings ............................................................................43
Quick Start .................................................................................43
Restore Default Settings ............................................................43
Settings for Playback..................................................................44
Settings for Recording................................................................44
Still Mode (paused video)...........................................................45
Black Level Control ....................................................................45
Dynamic Range Compression ...................................................45
Digital Audio Output ...................................................................45
Select Audio Channel For DV Input............................................46
Status Messages........................................................................46
On-screen Language .................................................................46
Front Display ..............................................................................47
Closed Caption...........................................................................47
TV Aspect...................................................................................47
4:3 TV settings for DVD-Video....................................................47
4:3 TV settings for DVD-RAM.....................................................48
Component Output Signal..........................................................48
Functions of HDMI .....................................................................48
Other Settings
Other Settings.......................................................................50
Using the Unit’s Remote Control to Operate the TV and the Set
Top Box (Cable Box, Satellite Receiver, etc.) .............................50

5
Getting Started
RQT9048
Reference
Adding a Video Cassette Recorder (VCR) ...........................52
Connecting to a Television, a Set Top Box and a VCR ...............52
Connection Options for Improved Playback Quality .............53
Using an S Video Cable for Better Video
(S Video Cable not included)..................................................53
Using Component Cables for Better Video
(Component Video Cables not included)................................53
Using an Audio Cable for Better Sound
(Audio Cable not included).....................................................53
Using an Optical Digital Audio Cable for Better Sound
(Optical Digital Audio Cable not included)..............................53
Using an HDMI (High Definition Multimedia Interface) Cable ....54
Media Information.................................................................54
Media Care.................................................................................54
Usable Discs for Recording and Playback .................................55
Play-only Discs...........................................................................56
Discs that Cannot be Played......................................................56
SD Cards Usable with this Unit ..................................................56
USB memories you can use with this unit..................................57
MP3 File Information ..................................................................57
Still Picture (JPEG) Information .................................................57
Frequently Asked Questions.............................................. 58
Setup..........................................................................................58
Discs ..........................................................................................58
USB............................................................................................58
Recording...................................................................................59
Language code list ...............................................................59
Error Messages ................................................................. 60
On the Unit’s Display..................................................................60
On the TV ...................................................................................61
Product Service ....................................................................61
Product information ....................................................................61
Troubleshooting Guide....................................................... 62
To Reset this Unit .......................................................................62
General Issues: Power ...............................................................62
General Issues: VIERA Link .......................................................62
General Issues: Operation .........................................................63
General Issues: USB..................................................................64
General Issues: Displays............................................................64
Playback Issues: Picture ............................................................65
Playback Issues: Sound .............................................................66
Playback Issues: Operation........................................................66
Recording Issues: Recording / Scheduled Recording / External Input ....67
Editing Issues: DVD & SD ..........................................................68
Editing Issues: Still Pictures .......................................................68
Glossary ...............................................................................69
Specifications .......................................................................70
Limited Warranty...................................................................71
Referencia rápida en espanõl (Spanish Quick Reference)...72
Index....................................................................... Back cover
Accessories
Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts.
(Product numbers correct as of December 2007. These may be subject to change.)
To order accessories, refer to “Accessory Purchases” on page 71.
1 Remote control (N2QAYB000211) 2 Batteries for remote control
1 Set Top Box Control cable
(K2ZZ02C00008)
1 Audio/video cable (K2KA2BA00003)
1 AC power supply cord (K2CB2CB00018)
For use with this unit only. Do not use it with
other equipment. Also, do not use cords for
other equipment with this unit.
•
Product Registration Card
Please complete and return the included product registration card, or register via the Internet at: http://www.prodreg.com/panasonic/
Remote Control Information
About batteries
Insert so the poles (+ and –) match those in the remote control.
Do not use rechargeable type batteries.
R6/LR6, AA
Do not mix old and new batteries.
Do not use different types at the same time.
Do not heat or expose to flame.
Do not leave the batteries in an automobile exposed to direct
sunlight for a long period of time with doors and windows closed.
Do not take apart or short circuit.
Do not attempt to recharge alkaline or manganese batteries.
Do not use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
Remove if the remote control is not going to be used for a long period
of time.
Store in a cool, dark place.
•
•
•
•
•
•
•
•
•
Using the remote control
Aim at the sensor, avoiding obstacles, up to a maximum range of
7 m (23 feet) directly in front of the unit.
20
20
30
30
Basic Operations
Advanced FeaturesAdvanced EditingSetting MenusOther Settings
ReferenceEspanõl

6
RQT9048
Main Unit
USB
/
1.3
RESET
SD CARD
IN2
DV IN S VIDEO VIDEO
L/MONO-AUDIO-R
INPUT
SELECT
REC MODE
REC
Opening the front panel
Pull down
2456789bk
The unit’s display
Remote control
signal sensor
1Disc tray
3bl
1POWER on/off button (POWER ^/I)......... (➔10)
Press to switch the unit from on to standby mode or vice versa.
In the standby mode, the unit is still consuming a small amount
of power.
2Connector for a digital video (DV)
camcorder................................................. (➔22)
3IN2 input terminals (IN2) .......................... (➔21)
4SD card slot ................................................ (➔7)
5USB Connector........................................... (➔7)
•
6Reset button ............................................. (➔62)
7Stop button ............................................... (➔13)
8Play/x1.3 button ........................................ (➔13)
9Input Select......................................... (➔14, 21)
bk Recording mode ....................................... (➔14)
bl Start recording .......................................... (➔14)
bm Disc tray open/close button ........................ (➔7)
Remote Control
1
4
5
7
6
3
9
bp
bq
bt
ck
cl
cm
8
bo
br
bs
bk
bl
bm
bn
cp
cq
cn
co
cr

2
1 Turn the unit on or off.............................................. (➔10)
2 Select the drive (DVD, SD or USB) ............(➔16, 25, 26)
3 Select channels and recording numbers etc./
Enter numbers ........................................................ (➔23)
4 Cancel
5 Basic operations for recording and play
6 Skip the specified time............................................ (➔24)
7 Direct Navigator ................................................ (➔23, 32)
8 Selection/Enter, Frame-by-frame...................... (➔10, 24)
9 Show sub menu................................................ (➔23, 32)
bk Select audio ............................................................ (➔24)
[A] for Recordings screen ....................................... (➔16)
bl Show on-screen menu............................................ (➔38)
[B] for Album View screen....................................... (➔26)
bm Start recording ........................................................ (➔14)
bn Change recording mode......................................... (➔14)
bo Transmission window
bp TV and Set Top Box operations.............................. (➔50)
bq Channel select........................................................ (➔14)
br Input select (IN1, IN2, DV)................................ (➔14, 21)
bs Sub channel access for digital broadcasts
bt Delete...................................................................... (➔16)
ck Skip 1 minute forward............................................. (➔24)
cl Show scheduled recording list................................ (➔15)
cm Show FUNCTIONS window ................................... (➔29)
cn Return to previous screen
co Show setup menu................................................... (➔42)
cp Create chapters ...................................................... (➔24)
cq Show status messages........................................... (➔28)
cr Start Flexible Recording ......................................... (➔19)
Control Reference Guide

7
RQT9048
Getting Started
Rear Panel
PR
PB
Y
COMPONENT
VIDEO OUT
AC IN
SET TOP BOX
CONTROL
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
R-AUDIO-L VIDEO S VIDEO
IN1 OUT
AV OUT
3
9 8 7bk
4 5 621
1 AC IN~ = Power supply
2 Cooling fan
3 AUDIO/VIDEO input terminal ................... (➔8)
4 S VIDEO input terminal
5 Set Top Box Control terminal.................... (➔8)
6 Digital audio output terminal................... (➔53)
7 HDMI AV OUT terminal ...................... (➔9, 54)
8 S VIDEO output terminal ........................ (➔53)
9 AUDIO/VIDEO output terminal ................. (➔8)
bk COMPONENT VIDEO OUT terminal ..... (➔53)
The Unit’s Display
12
345
1Recording indicator
2Main display section
3Disc indicator
This indicator lights up when a disc that is supported by this
unit is inserted.
4Scheduled recording indicator (➔15)
On:
When a scheduled recording program is registered and a
recordable disc is inserted.
Flashes:
The scheduled recording indicator flashes when the unit
cannot go to scheduled recording standby (e.g. there is no
disc, etc).
It does not flash if Quick Start is off.
5Progressive indicator
This indicator lights up when you select “24p” in
“Progressive/24p” (➔39).
Inserting Discs
; OPEN/CLOSE
to open the tray.
Insert a disc.
Press [;OPEN/CLOSE] again to close the
tray.
Insert label-up.
–
–
Notes
When using 8 cm (3˝) DVD-RAM or 8 cm (3˝) DVD-R, remove the
disc from the cartridge.
It is not possible to record or play continuously from one side of a double
sided disc to the other. You will need to eject the disc and turn it over.
The unit may take some time to respond to [;OPEN/CLOSE] when the
DVD Drive is selected with no disc in the drive.
Inserting an SD Card
Opening the front panel (➔6)
Inserting the card
Press on the center of
the card until it clicks
into place.
Insert the card label up with the
cut-off corner on the right.
Removing the card
Press on the center of the card
and pull it straight out.
ADAPTER
If you are using a miniSD card/
microSD card, insert it into the
card adaptor that comes with
the card.
Insert and remove this adaptor
from the unit.
Notes
When “SD” is flashing or when copying a picture or displaying the
Album in the SD card, do not turn off the unit or remove the SD card.
Such action may result in malfunction or loss of the card’s contents.
Inserting USB memory
You can insert the USB memory directly into the USB port.
Preparation
Before inserting any USB memory to this unit, ensure that the data
stored therein has been backed up.
Opening the front panel (➔6)
Inserting the USB memory
Check the orientation of the USB
connector and insert it straight in.
Removing the USB memory
Complete all USB memory-
related operations and pull the
USB memory straight out.
When “uSb” is flashing on the
unit’s display, do not turn off
the unit or remove the USB
memory.
Notes
There are few USB memory devices that cannot be connected.
Some USB devices inserted into this unit may cause this unit to stop
operating. Such USB devices cannot be used on this unit.
Confirm that “uSb” (USB) appears on the unit’s display when a
compatible USB memory is inserted while stopped.
If a USB memory being accessed is pulled out, then the data may
be damaged.
•
•
•
•
•
•
•
Media Handling

8
RQT9048
Basic Connection
Connecting to a Television and a Set Top Box
Consult your set top box provider about the appropriate Set Top Box to use.
Additional coaxial cable and audio/video (AV) cable are required.
Note: The terminals on the rear of your TV and Set Top Box may not appear as shown below.
Please read terminal labels carefully to ensure correct connections.
PR
PB
Y
COMPONENT
VIDEO OUT
OX
L
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
R-AUDIO-L VIDEO S VIDEO
IN1 OUT
AV OUT
AUDIO OUT
R L
VIDEO
OUT
RF IN/
SATELLITE IN RF OUT
VHF/UHF
RF IN
AUDIO IN
R L
VIDEO
IN
Rear of Set Top Box
Rear of this unit
step
6
SET TOP BOX
CONTROL
step
3
step
7
Red White Yellow
Red White Yellow
step
4
step
5
Red White Yellow
step
1
step
2
Rear of TV
• The Set Top Box Control
cable is necessary for
operating a set top box with
this unit’s remote control.
• Place the Set Top Box
Control cable in front of the
signal sensor of the set top
box.
Read the set top box operating
instructions regarding
positioning of the signal
sensor.
If necessary, use the double
sided adhesive tape (included)
to secure the Set Top Box
Control cable to a flat surface.
Red White Yellow
AC INAC INAC IN
Cable from the wall
or satellite antenna
To a household
AC outlet
(AC 120 V, 60 Hz)
75 Ωcoaxial cable from the wall or satellite antenna to the “RF IN” on the Set Top Box.
75 Ωcoaxial cable from the “RF OUT” on the Set Top Box to the “VHF/UHF RF IN” on the TV.
Audio/video cable (included) from the “OUT” on the unit to the “AV IN” on the TV.
Audio/video cable from the “AV OUT” on the Set Top Box to the “IN1” on the unit.
Connect the Set Top Box Control cable (included) to the back of this unit.
Install the Set Top Box Control cable (included) in front of Set Top Box.
AC power supply cord (included) from the “AC IN~” on the unit to a household AC outlet.
•
•

9
Getting Started
RQT9048
You can enjoy high-quality picture and audio by changing the audio/video (AV) cable connection between this unit
and your TV on page 8 as follows.
Connecting to a TV with an HDMI (High Definition Multimedia Interface) Cable
When connected to an HDMI compatible unit, an uncompressed digital audio and video signal is transmitted,
enabling you to enjoy high quality digital video and audio with just one cable. When connecting to an HDMI-
compatible HDTV (High Definition Television), the output can be switched to 1080p, 1080i or 720p HD video.
Regarding “HDAVI Control” function
When connecting with a Panasonic TV (VIERA) or a receiver equipped with “HDAVI Control” function, linked
operations are possible. [➔ 30, Linked Operations with the TV (VIERA Link™ “HDAVI Control™”)]
Please use HIGH SPEED HDMI cables that have the HDMI logo (as shown on the cover). It is
recommended that you use Panasonic’s HDMI cable.
Recommended part number: RP-CDHG10 (1.0 m/3.3 ft.), RP-CDHG15 (1.5 m/4.9 ft.),
RP-CDHG20 (2.0 m/6.6 ft.), RP-CDHG30 (3.0 m/9.8 ft.), RP-CDHG50 (5.0 m/16.4 ft.), etc.
Non-HDMI-compliant cables cannot be used.
•
•
PR
PB
Y
COMPONENT
VIDEO OUT
AC IN
SET TOP BOX
CONTROL
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
R-AUDIO-L VIDEO S VIDEO
IN1 OUT
AV OUT
Rear of TV
HDMI IN
Rear of this unit
HDMI cable
(not included)
Set “HDMI Priority” and “HDMI Audio Output” to “On” (➔ 48, 49). (The default setting is “On”.)
Notes
If connecting to equipment that is only compatible with 2 channel output, audio with 3 channels or more will be
down-mixed (➔ 69) and output as 2 channels (some discs cannot be down-mixed).
For display units compatible with HDCP (High bandwidth Digital Content Protection) that are equipped with a
digital DVI input terminal (PC monitors, etc.):
Depending on the unit, images may not display properly or at all when connecting with a DVI/HDMI switching
cable (audio cannot be output).
•
•
•
•

10
RQT9048
Setting the Set Top Box Control and Clock
Preparation:
Turn on the television and select the appropriate video
input to suit the connections to this unit (Example: AV input).
When using the set top box, make sure it is turned on.
These are the first settings you make upon buying the
unit. You don’t need to make these settings again.
•
•
•
to turn the unit on.
When this unit is connected to a Panasonic TV (VIERA)
supporting HDAVI Control 3 via an HDMI cable (➔9), it
acquires the setting information from the TV. When the
Quick Start Setting screen appears (➔below, step 4)
•
Language:
e, rto select, then
When the Quick Start Setting screen
appears after this step (➔below, step 4)
•
English
Español
Français
Press OK
Pulse OK
Appuyer sur OK
Select Language
Seleccione el idioma
Sélection de langue
TV Aspect Ratio:
e, rto select “4:3 TV” or
“16:9 Widescreen TV”, then
Aspect Ratio Selection
Select TV type and press OK.
(Please refer to Operation Instruction
for details)
4:3 TV
16:9 Widescreen TV
16:9
4:3
When connecting to a 4:3 standard aspect TV:
Select “4:3 TV”.
When connecting to a 16:9 widescreen TV:
Select “16:9 Widescreen TV”.
•
•
Quick Start Function:
e, rto select “On” or “Off”,
then
Quick Start Setting
The unit can be turned on faster, in about
1 second. Please note that Quick Start
mode slightly increases power
consumption when the unit is off.
(See Operation Instructions for details)
Turn Quick Start on ?
On
Off
Set Top Box Control Settings:
e, rto select “Yes”, then
If you do not control your set top box with
this unit: Select “No”.
The unit then displays “Set Clock Manually”
screen (➔12, step 10).
•
STB (Set Top Box) IR Settings
This unit can control your STB
(Set Top Box), when connected to IN1
input using the Set Top Box Control cable.
Start setup now?
Yes
No
12
Tips
“Quick Start” function (➔43)
If you set Quick Start to on, you can start
recording to DVD-RAM about 1 second
after you press [^DVD POWER] to turn
the unit on and then sequentially press
[*REC].
The following happens when you have
selected “On”.
Power consumption in standby mode
increases because power is supplied to
the unit.
To view programs from the set top box
If the TV is not directly connected to the
set top box, then turn on this unit in the
following cases:
“Quick Start” is “Off”.
“Quick Start” is “On” with this unit being
connected to the TV via a component or
HDMI cable.
To zoom in on video
1. Press [SUB MENU],
2. Press [e, r] to select “Zoom In”, then
press [OK].
To return to the previous screen
Press [RETURN].
•
–
•
–
–
•

11
Getting Started
RQT9048
STB (Set Top Box) IR Settings:
e, rto select an item, then
STB (Set Top Box) Type
Select the service being used.
Brand Name
Select the set top box brand.
You can also use [
u
] or [
i
] to view other pages.
Max. CH digits
Select the maximum number of channel digits to be entered in your
set top box. [This must not be selected when “Converter Box” is
selected for “STB (Set Top Box) Type”.]
OK Key Operation
Select whether or not the selected channel is confirmed by
pressing [OK] in accordance with your set top box.
–
–
–
–
Please choose settings based on your
Set Top Box.
OK
STB (Set Top Box) IR Settings
ABC
3 Digit
Brand Name
Cable Box/DVR
STB (Set Top Box) Type
Max. CH digits
Off
OK Key Operation
Test
e, rto select “Test”, then
Confirmation screen appears. –
8
The correct operation of the Set Top Box
Control cable is checked. Enter a channel
that can be received by your set top box.
w, qto select a position in
which the channel is entered
and e, rto set the number, then
You can also use the numbered buttons.–
Start Set Top Box Control testing.
Please input the channel number
for testing. Use either numbered
buttons or UP/DOWN Cursors.
OK
STB (Set Top Box) IR Settings
Channel :
STB Type: Cable Box/DVR
Brand Name: Panasonic
Max. CH digits: 3 Digit
OK Key Operation: On
IR Code: ○○
10
Number
0--
9
Confirmation screen appears.
e, rto select the item, then
Yes, try other channels
Even if this unit can select a channel
on the set top box, it is recommended to select “Yes, try other
channels” and verify whether or not other channels can be selected
and properly controlled (➔step 8).
Yes, complete setup
Exits the Set Top Box Control setting screen.
No, try another code
Select this option when there are channels that cannot be selected.
If channels cannot be selected as set,
then “Yes, start over again” or “No, exit” will
be displayed.
“Yes, start over again” : Returns to step 6.
Set the channels again.
“No, exit” : The set top box is not controlled
with this unit.
If any channel cannot be selected, then this unit cannot properly
control the set top box.
–
–
–
Completed testing the / IR codes.
STB (Set Top Box) IR Settings
Has the STB channel changed to the number you
selected? Please select from the following:
Note: “Yes, try other channels” is
recommended to try several channels.
Yes, try other channels
No, try another code
Yes, complete setup
IR Code :
Completed testing all of the %s codes.
Do you want to start over the test again?
No, exit
Yes, start over again
STB (Set Top Box) IR Settings
Continued on next page.

12
RQT9048
Setting the Set Top Box Control and Clock
10 Set Clock Manually:
w, qto select the item you want
to change.
Set Clock Manually
/:
/SAT AM
DST
EST
11 2000 12
Off
Time Zone
EST
00
Month Day Year Hour Minute
11 e, rto change the setting.
Repeat steps 10-11 to change other items.–
12
to confirm new date and time.
The clock starts.–
Notes
Time Zone
EST (Eastern Standard Time) = GMT –5
CST (Central Standard Time) = GMT –6
MST (Mountain Standard Time) = GMT –7
PST (Pacific Standard Time) = GMT –8
AST (Alaska Standard Time) = GMT –9
HST (Hawaii Standard Time) = GMT –10
For other areas: xx hr
DST (Daylight Saving Time)
If you select “On”, the clock is advanced one hour beginning at 2
a.m. on the second Sunday in March and ending at 2 a.m. on the
first Sunday in November.
Set the DST period manually when it varies according to regions
(➔below).
To set the DST period manually
1. Press [SETUP].
2. Press [e, r] to select “Setup” then press [q].
3. Press [e, r] to select “Clock Settings” then press [OK].
4. Press [e, r] to select “Set the time change dates for DST” then
press [OK].
5. Press [e, r, w, q] to set the “Month”, “Day”, “Hour”, and “Minute”
then press [OK].
Reinitializes the
settings.
Setup
Setup
Disc
Video
Audio
Display
TV Screen
Set the time change dates for DST
OK
:AM
3SUN2nd 2 00
Month
Beginning
Day Hour Minute
:AM
11 SUN1st 2 00
Restore Default
Month
End
Day Hour Minute
•
•
Acquiring the setting information from
the TV (VIERA)
If this unit is connected to a Panasonic TV (VIERA)
supporting HDAVI Control 3 via an HDMI cable, then
the setting information on the TV is acquired by this
unit when the unit is turned on for the first time.
Acquires the following information from the TV (VIERA).
Language
TV Aspect
Closed caption
The language setting screen may be displayed
depending on the usage environment. Press [e, r]
to select language, then press [OK].
When the settings are complete, the Set Top Box
Control Setting screen is displayed (➔10, step 5).
Notes
Acquisition of the setting information is not supported by all
Panasonic TVs (VIERA).
The acquisition may take some time depending on the VIERA
setting information.
•
–
–
–
•
•

13
RQT9048
Basic OperationsBasic Operations
Preparation:
Turn on the television and select the appropriate video input to suit the
connections to this unit (Example: AV input).
•
Playing Discs
Refer to “Advanced Playback” (➔23, 24) for detailed information on playback.
RAM -R -R DL -RW(V) +R +R DL +RW DVD-V -RW(VR) CD
to turn the unit on.
“HELLO” appears on the unit’s display.–
;
OPEN/CLOSE
to open the tray (Button located on the upper front of the unit) .
Insert a disc.–
The tray closes and play begins.–
Stopping Play
Press [gSTOP].
The stopped position is
memorized. (Resume play
function)
The stopped position is cleared
when you press [gSTOP]
two or more times, or press
[;OPEN/CLOSE].
–
–
Pausing Play
Press [hPAUSE].
Press again to restart play.–
Tips
Icons such as “ RAM ” indicate usable discs. Refer to pages 55 and 56.
Notes
The unit takes some time to read the disc before play starts.
Discs continue to rotate while menus are displayed. Press [gSTOP] when you finish to
preserve the unit’s motor and your television screen.
RAM -R -R DL -RW(V) +R +R DL +RW -RW(VR)
Playback starts from the most recent recording.
DVD-V CD
Playback starts from the beginning of the disc.
•
•
•
•
•
Playback
Getting Started

14
RQT9048
Recording Set Top Box Programs
Refer to “Important Notes for Recording” (➔17) and “Advanced Recording” (➔18, 19) for detailed information on
recording.
RAM -R -R DL -RW(V) +R +R DL +RW
Preparation:
Turn on the television and select the appropriate video input to suit the
connections to this unit (Example: AV input).
When using the set top box, make sure it is turned on.
RAM If the disc is protected, release protection (➔40).
•
•
•
to turn the unit on.
“HELLO” appears on the unit’s display.–
;
OPEN/CLOSE
to open the tray (Button located on the upper front of the unit).
Insert a disc with enough remaining blank space and press
[;OPEN/CLOSE] again to close the tray.
–
3a When the set top box is controlled with this unit:
to select desired channel.
or
3b When the set top box is not controlled with this unit:
to select “IN1” or “IN2”.
Select a channel on the connected equipment.–
to select the recording mode.
Recording mode should be determined by program length and
available time on the disc (➔18).
Recording mode Remaining time
–
to start recording.
REC
Pausing Recording
Press [hPAUSE].
Press again to restart recording.–
Stopping Recording
Press [gSTOP].
3a
Tips
Icons such as “ RAM ” indicate usable
discs. Refer to pages 55 and 56.
•
Notes
-R -R DL -RW(V) +R +R DL +RW
It takes about 30 seconds for the unit
to complete recording management
information after recording finishes.
You cannot change the channel or
recording mode during recording.
•
•
3b

15
RQT9048
Basic OperationsBasic Operations
Scheduled Recording
Refer to “Advanced Scheduled Recording” (➔20) for detailed information on scheduled recording.
RAM -R -R DL -RW(V) +R +R DL +RW
Preparation:
Turn on the television and select the appropriate video input to suit the
connections to this unit (Example: AV input).
When using the set top box, make sure the set top box is turned on.
RAM If the disc is protected, release protection (➔ 40).
Insert a disc with enough remaining blank space.
Confirm that the clock on the unit’s display is set to the correct time.
•
•
•
•
•
Schedule List Remaining Recording Time
3/26 Tue 12:53 PM
1:58 SPDVD
ChannelNo Date On
New Scheduled Recording
Off Mode Check
e, rto select “New Scheduled Recording”, then
w, qto move through the items and e, rto set
the items.
Channel/Input TV Station/External Input
When the set top box is controlled with this unit:
Press the numbered buttons to set the channel.
To enter a channel using the keypad:
1. Press [SUB MENU].
2. Press [e, r] to select “Show Keypad”, then press [OK].
3. Press [e, r, w, q] to select a character, then press [OK].
4. Press [gSTOP] when you’ve finished entering text.
To preview the scheduled recording channel:
1. Press [SUB MENU].
2. Press [e, r] to select “IR Test”, then press [OK].
When the set top box is not controlled with this unit:
Select the input to which the set top box is connected and set a
channel on connected equipment before scheduled recording starts.
Date/Frequency You can set a daily or weekly program.–
On (start time) / Off (end time)
Hold button to change in 30-minute increments.–
Mode Recording mode, see page 18.–
Name Press [OK], see page 29.–
To delete all items
1. Press [SUB MENU].
2. Press [e, r] to select “Delete”, then press [OK].
Preview of selected
channel
SCHEDULED
RECORDING
Channel/
Input Date/
Frequency
--------
On
-- : -- --
Off
-- : -- --
Mode
--
Name
4-1
Remaining Recording Time
3/26 Tue 12:53 PM
1:58 SPDVD
Set Channel/Input.
To input from the keypad,
please press SUB MENU.
Repeat steps 2−4 to program other recordings.–
when you have finished programming.
“z” lights on the unit’s display.
Scheduled recording can be started only when the unit
is turned off.
–
–
Notes
To prevent recording errors
Set a scheduled recording period slightly
longer than the actual program (to make
sure the program is recorded in full).
Be sure to perform step 5 before the
scheduled recording time. When the
unit is turned off, “z” lights on the unit’s
display to indicate scheduled recording
standby has been activated.
“z” flashes when the unit cannot go to
scheduled recording standby. (e.g., a
recordable disc is not in the disc tray)
It does not flash if Quick Start is off.
When scheduled recordings are set to
start one immediately after another, the
unit cannot record the beginning of the
later program.
If two scheduled recording times overlap
the recording that started first always
has priority. The second recording will
start only after the first recording has
finished.
When starting time for a scheduled
recording is the same, the recording that
you programmed later has priority.
Depending on the Daylight Saving Time
(DST) settings for this unit, scheduled
recordings may be affected when the
seasons change.
•
•
•
•
•
•
•
Tips
Icons such as “ RAM ” indicate usable
discs. Refer to pages 55 and 56.
•

16
RQT9048
Important: Once deleted, contents cannot be recovered.
Preparation:
Turn on the television and select the appropriate video input to suit the
connections to this unit (Example: AV input).
RAM If the disc is protected, release protection (➔40).
Insert the disc containing the recording to be deleted.
•
•
•
Delete Navigator
RAM -R -R DL -RW(V) +R +R DL +RW
to select the DVD drive.
With the unit stopped
Playback
Program
Delete
Other Functions
FUNCTIONS Cartridge Protection Off
Disc Protection Off
DVD-RAM
OK
e, rto select “Delete”, then
RAM When the Album View screen is displayed,
press to switch to the Recordings screen.
No.
--
0 9
DELETE Navigator
DVD-RAM Recordings
Page 02/02
Previous
10 10/27 Mon
Next
Delete
07
8 10/27 Mon
08
-- -- --
--
S
SUB MENU Select NextPrevious
Video Picture
B
A
No.
--
0 9
DELETE Navigator
DVD-RAM Recordings
Page 02/02
Previous
10 10/27 Mon
Next
Delete
07
8 10/27 Mon
08
-- -- --
--
S
SUB MENU Select NextPrevious
Video Picture
B
A
e, r, w, qto select the recording, then
wto select “Delete”, then
Tips
To return to the previous screen
Press [RETURN].
To view other pages
Press [e, r, w, q] to select “Previous” or “Next”, then press [OK].
You can also press [u, i] to view other pages.
Multiple editing
Select with [e, r, w, q], then press [hPAUSE]. (Repeat.)
A checkmark appears. Press [hPAUSE] again to cancel.
Delete Recordings During Playback
RAM -R -R DL -RW(V) +R +R DL +RW
During playback
wto select “Delete”, then
•
•
Deleting Recordings
Notes
You cannot delete while recording.
+R +R DL +RW Even if you have set
protection on other equipment, such
recordings are deleted.
Tips
Icons such as “ RAM ” indicate usable
discs. Refer to pages 55 and 56.
RAM Deleting an item increases the
available disc space by the amount of
space taken by the item deleted.
-R -R DL +R +R DL Available disc space
does not increase after deletion.
-RW(V) +RW Available disc space
increases when you delete the last
recording (the recording space may
increase slightly when other recordings
are deleted).
•
•
•
•
•
•

17
RQT9048
Advanced FeaturesAdvanced Features
Recording of
multilingual
broadcasts
from set top
box
RAM
Both Main and SAP audio can be recorded.
You can change the audio during playback (➔24, Changing
Audio during Playback).
Main SAP
Hello Hola
Select both “Main” and “SAP” on the
set top box.
-R -R DL -RW(V) +R +R DL +RW
Select the Main or SAP audio before
recording.
The selected audio only is recorded.
Main
Hello
Select “Main” or “SAP” on
the set top box.
Recording of
Widescreen
broadcasts
RAM
Recorded in 16:9 aspect (Widescreen)
-R -R DL -RW(V) +R +R DL +RW
Recorded in 4:3 aspect
If you have a regular 4:3 aspect TV and you receive 16:9 aspect images, they will appear in the letterbox format
(➔69, Letterbox).
•
Copy-once
Recording
It is not possible to record digital broadcasts that allow “One time only recording” onto DVD-R, DVD-R DL, DVD-RW,
+R, +R DL, +RW or 8 cm (3˝) DVD-RAM discs. Use the CPRM (➔69) compatible DVD-RAM.
•
RAM CPRM compatible discs only -R -R DL -RW(V) +R +R DL +RW
Yes No
When purchasing discs, check that they support CPRM.•
12 cm (5˝)
Playing the
disc on other
DVD players
-R -R DL -RW(V) +R +R DL
The disc must be finalized after recording (➔41).
All DVD-R, etc. discs recorded on this unit must be finalized before they can be played on other DVD players. Once
finalized DVD-R, etc. become “read-only” and can no longer be used for recording. DVD-RW can be reused after
finalizing.
Whether DL discs recorded on this unit can be played on other DVD players will depend entirely on the capabilities of
that player, 100% compatibility is not guaranteed.
CHG
SEARCH
ENTER
OFF
MENU
RETURN
TOPMENUDISPLA
Y
VOL
ON
A.SURROUND
MONITORMODE
PICTUREMODE
REPEA
T
OPEN
DCIN9V
ê/I ê CDSEQUENTIAL
DISC
DOUBLERE-MASTER ;º 1 :/65/9 DISCEXCHANGE DISCSKIP < OPEN/CLOSE
1 2345
Record to DVD-R, etc.
Finalize
Play on other DVD equipment
+RW We recommend you create the menu before playing a +RW disc on other equipment (➔41).
RAM
DVD-RAM can be played back on Panasonic DVD recorders and DVD-RAM compatible DVD players.
Recording
to DVD-R DL
and +R DL
DVD-R DL and +R DL discs have two layers of recording surface on one side.
-R DL Recordings are divided when recording changes from the first layer to the second. Some images and audio
may be lost at this point.
+R DL Recordings continue through the layer change with only a slight pause similar to what you will see with
commercial DVD-Video discs. Any recording exceeding 8 hours in length is automatically divided whether a layer
change is required or not.
•
•
The second layer
The available
space
The first layer
Recording 1 Recording 2
(Disc inner
side)
Recording/Playback direction
(Disc outer
side)
Layer change:
Recording divided,
some images and
audio lost.
Recording 3
DVD-R DL
Important Notes for Recording
Basic Operations

18
RQT9048
Recording Modes and Estimated Disc Recording Time
Recording Mode
DVD-RAM DVD-R,
DVD-RW, +R,
+RW (4.7 GB)
DVD-R DL*3,
+R DL*3 (8.5 GB)
Single-sided
(4.7 GB)
Double-sided*1
(9.4 GB)
XP (High quality) 1 hour 2 hours 1 hour 1 hour 45 minutes
SP (Standard play) 2 hours 4 hours 2 hours 3 hours 35 minutes
LP (Long play) 4 hours 8 hours 4 hours 7 hours 10 minutes
EP (Extra long play) 8 (6*2) hours 16 (12*2) hours 8 (6*2) hours 14 hours 20 minutes
(10 hours 45 minutes*2)
FR (Flexible Recording) 8 hours maximum 8 hours maximum
for one side 8 hours maximum 14 hours 20 minutes maximum
*1 It is not possible to record or play continuously from one side of a
double sided disc to the other.
*2 When “Recording Time in EP Mode” has been set to “EP-
Extended Play (6H)” in the Setup menu (➔44).
The sound quality is better when using “EP-Extended Play (6H)”
than when using “EP-Extended Play (8H)”.
*3 Refer to “Recording to DVD-R DL and +R DL” (➔17).
EP (6H)*2
EP (8H)
LP
SP
XP
Recording time
Picture quality
Notes
This unit uses variable bit rate (VBR) recording which varies the
amount of data recorded to suit the images, so actual recording
times and remaining recording times shown by the unit will be
different. (-R DL +R DL The difference will be especially noticeable.)
Use a disc with plenty of remaining time to be sure.
When recording to DVD-RAM using EP (8H) mode, play may not be
possible on DVD players, even if they are compatible with DVD-
RAM. In this case use EP (6H) mode.
When the format confirmation screen is
displayed
Important:
Formatting permanently deletes all disc contents (including
computer data), regardless of protection status of disc.
RAM -RW(V) +RW
The following screen may
appear when inserting a new
disc, etc.
Only format the disc if you
intend to use it for recording.
Do not format if you intend to view pre-recorded
material from the disc.
This disc is not formatted properly.
Do you want to format the
disc in DVD Management?
Format
No
Yes
wto select “Yes”, then
Tips
Refer to “Formatting Discs or Cards” (➔40) for more detail of formatting.
It will take several minutes to format the disc. (DVD-RAM may
take up to a maximum of 70 minutes.)
•
•
•
•
FR (Flexible recording mode)
Using “Flexible Recording” is convenient in these kinds of situations:
When the amount of free space on the disc makes selecting an
appropriate recording mode difficult
When you want to record a long program with the best picture
quality possible
e.g., Recording a 90 minutes program to 4.7 GB DVD-RAM disc:
4.7 GB
DVD-RAM
4.7 GB
DVD-RAM
4.7 GB
DVD-RAM
4.7 GB
DVD-RAM
A second disc is necessary for
30 minutes of the program.
If you select SP mode, the program will fit on one disc.–
However there will be 30 minutes
remaining disc space.
If you select “Flexible Recording” the program will fit on one disc
perfectly.
–
If you select XP mode, the program will not fit on one disc.–
You can set FR mode when programming scheduled recordings
(➔15) and flexible recording (➔19).
Tips
Maximum number of recordings to a disc
RAM -R -R DL -RW(V) 99 recordings on a disc
+R +R DL +RW 49 recordings on a disc
When removing a Recorded Disc
-R -R DL -RW(V) +R +R DL
After recording, if you press
[;OPEN/CLOSE] to eject
the disc, the following screen
may appear.
Finalizing is necessary to enable playback
of the disc on compatible DVD players.
Once finalized, recordings cannot be added to the disc.
It will take approximately minutes. Start ?
Press "REC" to start finalizing.
Press the OPEN/CLOSE button to postpone
finalizing.The disc can be played only on
this unit.You can Finalize it later.
Finalize
to start finalizing.
or
; OPEN/CLOSE
to eject the disc without finalizing.
Notes
You cannot stop finalizing once you have started it.
Tips
If you want to provide the disc with a name or set play menu select,
select “Disc Name” (➔40) or “Playback will start with:” (➔41) in
“DVD Management” before finalizing.
Refer to “Finalizing” (➔41) for more detail of finalizing
It will take a few minutes to finalize the disc. (Some discs may take
up to a maximum of 60 minutes.)
•
–
–
•
•
•
•
•
Advanced Recording

19
RQT9048
Advanced Features
Specifying the Recording Time
RAM -R -R DL -RW(V) +R +R DL +RW
This function allows specifying the length of recording
time up to 4 hours.
During recording
repeatedly until the desired
time is reached.
The recording time and the unit’s display change
as follows:
–
OFF 4:00 OFF 1:30
Counter (Cancel) OFF 0:30 OFF 1:00
OFF 3:00 OFF 2:00
Notes
This function does not work during scheduled recording or Flexible
Recording.
Recording stops and the set time is cleared if you press [gSTOP].
The unit turns off automatically when the time to stop recording is
reached as long as you do not operate the unit.
Flexible Recording
RAM -R -R DL -RW(V) +R +R DL +RW
The unit sets the best possible picture quality that fits
the recording within the remaining disc space.
The recording mode becomes FR mode. Refer to “FR
(Flexible Recording)” (➔18).
With the unit stopped
Flexible Recording
Record in FR mode.
Max recording time 08 Hour 00 Min.
08 Hour 00 Min.
CancelStart
Set recording time
w, qto select “Hour” and “Min.”
and e, rto set the recording time.
When you want to start recording
e, r, w, qto select “Start”, then
Recording starts.–
Tips
To exit the screen
Press [RETURN].
To stop recording partway
Press [gSTOP].
To show the remaining recording time
Press [STATUS] to show the remaining recording time.
Rec. 0:59
Stereo
DVD-RAM
CH 20
Remaining time
•
•
•
Playing while you are recording
Chasing Playback
RAM
Allows playback from the beginning of what you are
recording.
When recording to DVD-RAM
(at least 20 seconds after
recording starts).
If the “Status Messages” in the Setup menu is set
to “Automatic” (➔46), both the “Play” and “Rec.”
indicators will be displayed on the status message
screen for several seconds.
–
Tips
To stop play
Press [gSTOP] once.
To stop recording
Press [gSTOP] at least 2 seconds after chasing playback stops.
Simultaneous Record and Playback
RAM
Allows playback of a previous recording, while
recording something else.
When recording to DVD-RAM
e, r, w, qto select the
recording to play, then
If the “Status Messages” in the Setup menu
is set to “Automatic” (➔46), both the “Play”
and “Rec.” indicators will be displayed on the
status message screen for several seconds.
–
Tips
To stop play
Press [gSTOP].
To exit the DIRECT NAVIGATOR screen
Press [DIRECT NAVIGATOR].
To stop recording
After play stops
1. Press [DIRECT NAVIGATOR] to exit the screen.
2. Press [ gSTOP].
Notes
During playing while you are recording, you cannot edit or delete
recordings.
Closed captions will not appear during simultaneous recording and
playback.
Use caution while operating the control for playback. Pressing
[gSTOP] when the recording device is selected will cancel the
recording in progress.
•
•
•

20
RQT9048
To cancel a scheduled recording in
progress
to select the DVD drive.
Confirmation screen appears.–
wto select “Stop recording”, then
Notes
Recording stops and ‘one-time’ programs are deleted from the Schedule
List. Programs scheduled to record ‘Daily’ and ‘Weekly’ remain on the
Schedule List and are set to begin at the next scheduled time.
Check, Change, or Delete Programs
The scheduled recording list can be viewed even when
the unit is in “recording standby” mode.
See “Tips” (➔right) for explanation of icons
displayed.
–
e, rto select the program.
3a to modify the program.
e, r, w, qto make changes,
then
3b
or
, then to delete.
You cannot delete programs that are currently
recording.
–
“z” lights on the unit’s display.–
Notes
If the program schedule is changed by the TV station, then this unit
will not be able to detect the change.
Tips
You can enter up to 16 programs a month in advance.
Schedule List Remaining Recording Time
3/26 Tue 12:53 PM
1:58 SPDVD
ChannelNo Date On
New Scheduled Recording
Off Mode Check
AB
ASchedule List screen icons
*: Currently recording
: Programs are overlapped. Recording of the program with
the later start time starts when the earlier program finishes
recording.
Q: You stopped a weekly or daily scheduled recording. The icon
disappears when the next scheduled recording starts.
: The disc was full. (not enough space)
: The TV program may not be recorded due to copy-protect.
X: Recording stopped (Dirty disc, etc.)
BCheck
OK: Recordable
➔(Date):The last day of daily or weekly recording.
!: It may not be possible to record because:
the disc is write-protected.
there is no more space left.
the number of possible recordings has reached its
maximum.
Overlap: When the date and time overlap with another scheduled
recording, only a part of the program can be recorded.
To release the unit from recording
standby
(Before recording starts)
The unit turns on and “z” on the unit’s
display goes out.
–
Be sure to press [^DVD POWER] to return the unit to standby mode
before the scheduled recording time. Scheduled recording will work
only if “z” is displayed.
•
–
–
–
Advanced Scheduled Recording