Panasonic ES-SA40 User manual

© Panasonic Electric Works Co., Ltd. 2008.
All rights reserved. Unauthorized copying and distri-
bution is a violation of law.
Order Number SD0811E60CE2
Rechargeable Shaver
Model No. ES-SA40
Europe
Russia
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------- 6
6 Schematic Diagram ---------------------------------------------- 6
7 Exploded View and Replacement Parts List ------------ 7

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide

4
4 Disassembly and Assembly Instructions
4.1. Disassembly Instructions
Follow the procedure below to disassemble the main unit.
1. Remove the protective cap, the outer foil frame and the
inner blade.
2. Slide the trimmer approx. 8mm to upper side, and remove
the trimmer by using straight -edge screwdriver.
Note :
If you remove the trimmer by forcing, it is easy to
break.
3. Remove the trimmer driving bar by pressing it outward.
4. Loosen two screws, and remove the retaining plate and
the waterproof rubber.
Note :
Be careful not to lose the O-rings.
5. Remove the blade holder.

5
6. Set the switch to "OFF", and remove the chassis assembly from the housing.
4.2. Caution in Assembly
Note :
When reassembling, replace the new waterproof rubber. Make sure that there is NO foreign substance around a part covered
with waterproof rubber.
1. Driving Head
Insert a motor tip pin into the hole of driving head and
install driving head in chassis.
2. Waterproof Rubber
The waterproof rubber must be fitted properly. Install by
inserting firmly to the set position as the following Fig.

6
3. Trimmer
Set the trimmer at the upward position of 8mm as the fol-
lowing Fig, and hook it.
4. Buttery/Plug lever
Make sure of the position for O-ring and washer.
5 Wiring Connection Diagram
6 Schematic Diagram

Model No. : ES-SA40 Exploded View
7 Exploded View and Replacement Parts List

Model No. : ES-SA40 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 WESSA40X7158 PROTECTIVE CAP 1 (BG)
2 WESSA40K0048 OUTER FOIL FRAME 1 (Black EU)
2 WESSA40S0048 OUTER FOIL FRAME 1 (Silver EU/Russia)
3 WES9941Y OUTER FOIL 1
4 WES9942Y INNER BLADE 1
5 WES701S9707 SCREW 2 (*C)
6 WESSA60L0207 RETAINING PLATE 1 (BG)
7 WESSA60L1087 TRIMMER DRIVING BAR 1 (BG)
8 WESSA60L0327 WATERPROOF RUBBER 1 (BG)
9 WESSA60L1247 DRIVING HEAD 1 (BG)
10 WESSA40K0008 BLADE HOLDER 1 (Black EU), (BG)
10 WESSA40S0008 BLADE HOLDER 1 (Silver EU/Russia), (BG)
11 WESSA40L0778 CHASSIS 1 (BG)
12 WESSA60L1007 MOTOR BLOCK 1 (BG)
13 WESSA40L2508 RECHARGEABLE BATTERY 1 (Ni-MH), (BG)
14 WESSA40K3158 HOUSING 1 (Black EU), (BG)
14 WESSA40S3158 HOUSING 1 (Silver EU/Russia), (BG)
15 WESSA40K1508 TRIMMER 1 (BG)
16 WESSA40K3848 BOTTOM COVER 1 (Black EU), (BG)
16 WESSA40S3848 BOTTOM COVER 1 (Silver EU), (BG)
16 WESSA40S3849 BOTTOM COVER 1 (Silver Russia), (BG)
17 WESSA60L6007 SCREW 1 (BG)
18 WESSA40K3038 BODY BLOCK 1 (Black EU), (BG)
18 WESSA40S3038 BODY BLOCK 1 (Silver EU), (BG)
18 WESSA40S3039 BODY BLOCK 1 (Silver Russia), (BG)
19 WESSA40K7659 CHARGING ADAPTOR 1 (EU (C2-plug)), (BG)
19 WESSA40K7650 CHARGING ADAPTOR 1 (Russia (C2-plug)), (BG)
20 WES861B7056 CLEANING BRUSH 1 (BG)
- WESES40K8009 INDIVIDUAL BOX 1 (Black EU), (BG)
- WESES40S8009 INDIVIDUAL BOX 1 (Silver EU), (BG)
- WESES40S8000 INDIVIDUAL BOX 1 (Silver Russia), (BG)
- WESES40K8109 OPERATING INSTRUCTIONS 1 (EU), (BG)
- WESES40K8100 OPERATING INSTRUCTIONS 1 (Russia), (BG)