Panasonic ES-3040 User manual

1 SCHEMATIC DIAGRAM 2
2 WIRING CONNECTION DIAGRAM 2
3 DISASSEMBLY METHOD 3
4 CAUTION IN ASSEMBLY 4
©2001 Matsushita Electric Works, Ltd. All rights
reserved. Unauthorized copyingand distribution is a
violation of law.
ES3040
ES3041
ES3042
5 TROUBLESHOOTING GUIDE 5
6 EXPLODED VIEW 6
7 REPLACEMENT PARTS LIST 6
Wet/Dry Rechargeable Shaver
SPECIFICATIONS
Power source
A
C100-120V, 50-60Hz
(Automatic voltage conversion)
Motor voltage 1.2V DC
Power consumption 6W
Charging time 8-hours
Weight 140g
<SUPPLIED ACCESSORIES>
Soft case
CONTENTS
Page Page
ORDER NO.SD0102U31C1
E6

1 SCHEMATIC DIAGRAM
2 WIRING CONNECTION DIAGRAM
2
ES3040 / ES3041 / ES3042

3 DISASSEMBLY METHOD
1. Remove cap, foil frame and inner blade.
2. Unhook right and left side of hooks at upside using a flat
screwdriver with a position 8mm sliding above. Then slightly
move trimmer until position marking 2 , and unhook
lower side of hooks.
3. To remove trimmer driving bar, press bar outward.
4. Loosen two screws and lift rubber retaining plate away.
Take out waterproof rubber and two O-rings.
5. Take out the chassis block from housing by pushing a head
of driving head down with switch OFF.
6. Loosen two screws and remove bottom cover.
NOTE : When reassembling, replace the new waterproof
rubber.
Follow the procedure below to disassemble the main block.
3
ES3040 / ES3041 / ES3042

To remove battery, fix the top of battery terminal with a flat
plate and lifting up the battery pin.
1. Bottom Cove
Make sure whether there is NO foreign substance sticking
around a part covered with water weal.
2. Chassis
Make sure of terminal plates whether there is No
deformation or their condition.
3. Driving Head
Insert a motor tip pin into the hole of driving head and install
driving head in chassis.
The driving head waterproof rubber must be fitted the right way
around.
Install as shown in figure by inserting firmly to the set position.
Set a position where marking 2 , and hook lower side of
two hooks.
With a position 8mm sliding down, hook right and left side of
hooks at upside.
3.1. BATTERY REPLACEMENT
4 CAUTION IN ASSEMBLY
4. Waterproof Rubber
5. Trimmer
4
ES3040 / ES3041 / ES3042

5 TROUBLESHOOTING GUIDE
< SYMPTOM > < CAUSE > < REMEDY >
NO
Motor does not rotate. —<CHECK CHARGING ADAPTOR.> →Replace charging adaptor.
Does not charge Connect to rated voltage. OK if it is approximately
DC 1.5V-3.0V between - .
↓OK
NO
<CHECK CONTACT CONDITIONS OF SWITCH.> →Repair contact of negative con
Check for proper contact between negative contactspring and tact spring.
terminal pin when terminal pin is depressed.
↓OK
NO
<CHECK SWITCH.> →Repair contact or replace
Check contacts of switch. chassis.
↓OK
NO
<CHECK MOTOR.> →Replace motor.
Okay if motor rotates when DC1.2V is applied to (+) and (-)
terminals.
↓OK
NO
<CHECK RECHARGEABLE BATTERIES.> →Replace rechargeable battery.
Okay if voltage of rechargeable battery is more than
approximately 1.2V between (+) and (-) terminals.
*The rechargeable battery has a limited life. The battery
should be replaced if
OK - after being charged for the rated charging time,
battery voltage is less than DC 1.2V or an usabletime
is extremely short.
-the battery leaks. Check battery for leaks and
terminals for white powder or green corrosion.
<CHECK CHARGING CURRENT>
Connect lead wire to charging adaptor and
measure charging current across and .
Okay if it is 160±20mA.
5
ES3040 / ES3041 / ES3042