Panasonic WH-MHF09G3E5 User manual

There are
s
Diagrams,
C
with manu
f
manufactu
r
This service
It does not c
Products po
w
service or r
e
In or
d
s
pecial compo
n
C
ircuit Board D
i
f
acturer’s speci
f
r
er.
information is
ontain warnin
g
w
ered by elec
t
e
pair the produ
c
d
er to avoid fro
n
entsusedint
h
i
agrams, Explo
d
f
ied parts to p
r
designed for
e
g
s or cautions
t
t
ricity should b
e
c
t or products
d
stbite, be ass
u
IMPOR
T
h
is equipment
w
d
ed Views and
R
r
event shock, f
e
xperienced re
p
t
o advise non-
t
e
serviced or r
e
d
ealt with in th
PRECAUT
red of no refri
g
T
A
NT S
A
F
E
w
hich are impo
R
eplacement P
ire or other ha
WARNI
N
p
air technician
s
t
echnical indivi
d
e
paired only b
y
is service info
r
T
ION OF LOW
g
erant leakage
E
T
Y
NOTI
C
rtant for safety
.
arts List. It is e
s
zards. Do not
N
G
s
only and is n
d
uals of poten
t
y
experienced
r
mation by any
o
TEMPERATU
during the ins
t
C
E
.
These parts
a
s
sential that the
modify the ori
g
o
t designed fo
r
t
ial dangers in
p
rofessional t
e
o
ne else could
R
E
t
allation or rep
a
© Panas
o
Order N
o
Mon
o
WH-
M
WH-
M
D
a
re marked by
se critical parts
g
inal design wi
t
r use by the g
e
attempting to
s
e
chnicians. An
y
d
result in serio
airing of refrig
e
o
nic Corporatio
n
o
. PAPAMY15
0
o
Bloc
U
M
HF09
G
M
HF12
G
D
estina
Eu
r
Tu
r
in the Sche
m
should be repl
a
t
hout permissi
o
!
e
neral public.
s
ervice a prod
u
y
attempt to
us injury or de
a
e
rant circuit.
n
2015.
0
6105CE
U
nit
G
3E5
G
6E5
tion
r
ope
r
key
m
atic
a
ced
o
nof
u
ct.
a
th.

2
TABLE OF CONTENTS
PAGE PAGE
1. Safety Precautions .............................................3
2. Specifications .....................................................5
2.1 WH-MHF09G3E5...........................................5
2.2 WH-MHF12G6E5...........................................7
3. Features...............................................................9
4. Location of Controls and Components..........10
4.1 Mono Bloc Unit.............................................10
5. Dimensions .......................................................20
5.1 Mono Bloc Unit.............................................20
6. Refrigeration and Water Cycle Diagram ........21
7. Block Diagram ..................................................23
7.1 WH-MHF09G3E5.........................................23
7.2 WH-MHF12G6E5.........................................24
8. Wiring Connection Diagram ............................25
8.1 WH-MHF09G3E5.........................................25
8.2 WH-MHF12G6E5.........................................26
9. Electronic Circuit Diagram ..............................28
9.1 WH-MHF09G3E5.........................................28
9.2 WH-MHF12G6E5.........................................29
10. Printed Circuit Board .......................................31
10.1 Water system ...............................................31
10.2 Refrigerant System ......................................33
11. Installation Instruction.....................................35
11.1 Select The Best Location.............................37
11.2 Mono Bloc Unit Installation ..........................37
11.3 Piping Installation.........................................38
11.4 Connect The Cord And Cable To Mono
Bloc Unit.......................................................39
11.5 Checking and Test Run Procedures............45
12. Operation and Control .....................................46
12.1 Basic Function .............................................46
12.2 Water Pump .................................................57
12.3 Pump Down Operation
[Service Mode: 01] .......................................59
12.4 Flow Switch..................................................59
12.5 Mono Bloc Unit Safety .................................60
12.6 Auto Restart Control ....................................60
12.7 Indication Panel ...........................................60
12.8 Back-Up Heater Control...............................61
12.9 Tank Booster Heater Control .......................62
12.10Base Pan Heater Control (Optional)............62
12.11Sterilization Mode ........................................63
12.12Quiet Operation............................................63
12.13Anti Freeze Control ......................................64
12.14Solar Operation (Optional)...........................65
12.15External Room Thermostat Control
(Optional) .....................................................68
12.16Three Ways Valve Control...........................69
12.17External OFF/ON Control ............................69
12.18Holiday Mode ...............................................70
12.19Dry Concrete Function .................................70
13. Protection Control............................................71
13.1 Protection Control for All Operations ...........71
13.2 Protection Control for Heating Operation.....73
14. Servicing Mode .................................................75
14.1 Remove The Cabinet Front Plate ................75
14.2 Test Run ......................................................75
14.3 Proper Pump Down Procedure....................75
14.4 How To Adjust Water Flow Rate..................76
14.5 Expansion Vessel Pre Pressure
Checking ......................................................76
14.6 Dry Concrete [SERVICE MODE: 03] ...........76
14.7 EEPROM Factory Default Data Setup
Procedure ....................................................77
15. Maintenance Guide...........................................78
16. Troubleshooting Guide....................................80
16.1 Refrigeration Cycle System .........................80
16.2 Relationship Between The Condition Of
The Mono Bloc Unit And Pressure And
Electric Current ............................................81
16.3 Breakdown Self Diagnosis Function ............82
16.4 Error Codes Table........................................83
16.5 Self-diagnosis Method .................................85
17. Disassembly and Assembly Instructions ... 123
17.1 To Remove The Cabinet Front Plate ........ 123
17.2 To Remove The Cabinet Top Plate .......... 123
17.3 To Remove The Cabinet Rear Plate......... 124
17.4 To Remove Pressure Gauge .................... 124
17.5 To Remove RCCB .................................... 124
17.6 To Remove Transformer and Electronic
Controller Board........................................ 125
17.7 To Remove Pressure Relief Valve, Flow
Switch and Air Purge Valve ...................... 125
17.8 To Remove Water Pump .......................... 126
17.9 To Remove Bottle Complete..................... 127
18. Technical Data ............................................... 128
18.1 Operation Characteristics ......................... 128
18.2 Heating Capacity Table............................. 130
19. Exploded View and Replacement Parts
List .................................................................. 131
19.1 (Refrigerant System)................................. 131
19.2 (Water System) ......................................... 136

3
1. Safety Precautions
Read the following “SAFETY PRECAUTIONS” carefully before installation of (Mono bloc) Air-to-Water Heatpump
system (hereafter referred to as “Mono bloc unit”).
Electrical works and water installation works must be done by licensed electrician and licensed water system
installer respectively. Be sure to use the correct rating and main circuit for the model to be installed.
The caution items stated here must be followed because these important contents are related to safety. The
meaning of each indication used is as below. Incorrect installation due to ignorance or negligence of the
instructions will cause harm or damage, and the seriousness is classified by the following indications.
WARNING This indication shows the possibility of causing death or serious injury.
CAUTION This indication shows the possibility of causing injury or damage to properties only.
The items to be followed are classified by the symbols:
This symbol denotes item that is PROHIBITED from doing.
Symbol with dark background denotes item that must be carried out.
Carry out test run to confirm that no abnormality occurs after the installation. Then, explain to user the operation, care and
maintenance as stated in instructions. Please remind the customer to keep the operating instructions for future reference.
If there is any doubt about the installation procedure or operation, always contact the authorized dealer for advice and
information.
WARNING
1. Do not install Mono bloc unit near handrail of veranda. When installing Mono bloc unit at veranda of high rise building, child may climb
up to Mono bloc unit and cross over the handrail and causing accident.
2.
Do not use unspecified cord, modified cord, join cord or extension cord for power supply cord. Do not share the single outlet with other
electrical appliances.
Poor contact, poor insulation or over current will cause electrical shock or fire.
3. Do not tie up the power supply cord into a bundle by band. Abnormal temperature rise on power supply cord may happen.
4. Do not insert your fingers or other objects into the unit, high speed rotating fan may cause injury.
5. Do not sit or step on the unit, you may fall down accidentally.
6. Keep plastic bag (packaging material) away from small children, it may cause suffocation.
7. Do not use pipe wrench to install refrigerant pipe. It might deform the piping and cause the unit to malfunction.
8. Do not purchase unauthorized electrical parts for installation, service, maintenance and etc.. They might cause electrical shock or fire.
9. This unit is a multi supply appliances. All circuits must be disconnected before accessing to the unit terminals.
10. Do not modify the wiring of Mono bloc unit for installation of other components (i.e. heater, etc.). Overloaded wiring or wire connection
points may cause electrical shock or fire.
11. Do not add or replace refrigerant other than specified type. It may cause product damage, burst and injury etc.
12.
For electrical work, follow the local national wiring standard, regulation and this installation instruction. An independent circuit and
single outlet must be used. If electrical circuit capacity is not enough or defect found in electrical work, it will cause electrical shock or
fire.
13. For water circuit installation work, follow to relevant European and national regulations (including EN61770) and local plumbing and
building regulation codes.
14. Must engage an authorized dealer or specialist for installation. If installation is defective, it will cause water leakage, electrical shock or
fire.
15. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electrical shock or fire.
16. Only use the supplied or specified installation parts. Else, it may causes Mono bloc unit vibrate, fall, water leakage, electrical shock or
fire.
17. Install at a flat, strong and firm location which is able to withstand the Mono bloc unit’s weight. If the location is slanting, or strength is
not enough the set will fall and cause injury.

4
WARNING
18. This equipment is strongly recommended to be installed with Residual Current Device (RCD) on-site according to the respective
national wiring rules or country-specific safety measures in terms of residual current.
19. The unit is only for use in a closed water system. Utilization in an open water system may lead to excessive corrosion of the water
piping and risk of incubating bacteria colonies, particularly Legionella, in water.
20. If there is any doubt about the installation procedure or operation, always contact the authorized dealer for advice and information.
21. Select a location where in case of water leakage, the leakage will not cause damage to other properties.
22. When installing electrical equipment at wooden building of metal lath or wire lath, in accordance with electrical facility standard, no
electrical contact between equipment and building is allowed. Insulator must be installed in between.
23. This installation may be subjected to building regulation approval applicable to respective country that may require to notify the local
authority before installation.
24. Any work carried out on the Mono bloc unit after removing the front panel which is secured by screws, must be carried out under the
supervision of authorized dealer and licensed installation contractor.
25.
This unit must be properly earthed, the electrical earth must not be connected to a gas pipe, water pipe, the earth of a lightning rod or
a telephone. Otherwise there is a danger of electrical shock in the event of an insulation breakdown or electrical earth fault in the
Mono bloc unit.
CAUTION
1. Do not install the Mono bloc unit in areas where there is a risk of flammable gas leakage. There is a risk of fire if flammable gas
accumulates near or around the Mono bloc unit.
2. Do not release refrigerant during piping work for installation, re-installation and during repairing a refrigeration parts. Take care of the
liquid refrigerant, it may cause frostbite.
3. Make sure the power supply cord does not contact with hot part (i.e. water piping). High temperature may cause insulator of power
supply cord damage hence electrical shock or fire.
4.
Do not touch the sharp aluminum fins or edges of metal parts.
If you are required to handle sharp parts during installation or servicing, please wear hand glove.
Sharp parts may cause injury.
5. Do not apply excessive force to water pipes that may damage the pipes. If water leakage occurs, it will cause flooding and damage to
other properties.
6. Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water leakage may happen and may
cause damage to properties of the user.
7. The piping installation work must be flushed before the Mono bloc unit is connected to remove contaminants. Contaminants may
damage the Mono bloc unit components.
8. Select an installation location where it is accessible for maintenance.
9.
Power supply connection to the Mono bloc unit.
Power supply point should be in easily accessible place for power disconnection in case of emergency.
Must follow local national wiring standard, regulation and this installation instruction.
Strongly recommended to make permanent connection to a circuit breaker. It must be a double pole switch with a minimum
3.0 mm gap.
- Power supply 1: Use approved 40A circuit breaker
- Power supply 2: Use approved 40A circuit breaker
10. Ensure the correct polarity is maintained throughout all wiring. Otherwise, it will cause electrical shock or fire.
11. After installation, the installer is obliged to verify correct operation of the Mono bloc unit. Check the connection point for water leakage
during test run. If leakage occurs, it will cause damage to other properties.
12.
Installation work.
Four or more people are required to carry out the installation work. The weight of Mono bloc unit might cause injury if carried by less
than four people.

5
2. Specifications
2.1 WH-MHF09G3E5
Item Unit Refrigerant System
Performance Test Condition EN14511
Heating Capacity
Condition
(Ambient/Water) A7W35 A2W35
kW 9.00 9.00
BTU/h 30700 30700
kcal/h 7740 7740
COP W/W 4.64 3.45
kcal/hW 3.99 2.97
Air Flow m3/min (ft3/min) 76.8 (2710)
Refrigeration Control Device Expansion Valve
Refrigeration Oil cm3FV50S (1600)
Refrigerant (R407C) g (oz) 1.92k (67.8)
Compressor
Type Hermetic Motor / Rotary
Motor Type Brushless (4-poles)
Rated Output kW 3.40
Fan
Type Propeller Fan
Material PP
Motor Type DC (8-poles)
Input Power W —
Output Power W 60
Fan Speed rpm 490 (Top Fan) 530 (Bottom Fan)
Heat Exchanger
Fin material Aluminium (Pre Coat)
Fin Type Corrugated Fin
Row × Stage × FPI 2 × 51 × 18
Size (W × H × L) mm 903.7 × 1295.4 × 38.1
Item Unit Mono Bloc Unit
Dimension
Height mm (inch) 1410 (55-1/2)
Width mm (inch) 1283 (50-1/2)
Depth mm (inch) 320 (12-19/32)
Net Weight kg (lbs) 151 (333)
Noise Level dB-A 49
Power Level dB 66
Power Source (Phase, Voltage, Cycle)
ø Single
V 230
Hz 50
Input Power kW 1.94 2.61
Maximum Input Power For Mono Bloc Unit kW 6.09
Power Supply 1: Phase (ø) / Max. Current (A) / Max. Input Power (W) Single / 28.5 / 6.09k
Power Supply 2: Phase (ø) / Max. Current (A) / Max. Input Power (W) Single / 13.0 / 3.00k
Power Supply 3: Phase (ø) / Max. Current (A) / Max. Input Power (W) - / - / -
Starting Current A 9.3
Running Current A 9.3 12.5
Maximum Current For Mono Bloc Unit A 28.5
Power Factor % 91 91

6
Item Unit Mono Bloc Unit
Power factor means total figure of compressor and outdoor fan motor.
Power Cord Number of core -
Length m (ft) -
Thermostat Electronic Control
Protection Device Electronic Control
Item Unit Water System
Performance Test Condition EN14511
Operation Range Outdoor Ambient °C -20 ~ 35
Water Outlet °C 25 ~ 65
Internal Pressure Differential kPa 26.5
Water Pipe Diameter Inlet mm (inch) 30 (1-3/16)
Outlet mm (inch) 30 (1-3/16)
Water Drain Hose Inner Diameter mm (inch) 15.00 (19/32)
Pump
Motor Type DC Motor
No. of Speed 7 (Software Selection)
Input Power W 58
Hot Water Coil
Type Brazed Plate
No. of Plates 80
Size (W x H x L) mm 130 × 93 × 325
Water Flow Rate l/min (m3/h) 25.8 (1.5)
Pressure Relief Valve Water Circuit kPa Open: 300, Close: 265 and below
Flow Switch Magnetic Lead Switch
Protection Device A Residual Current Circuit Breaker (40)
Expansion Vessel Volume I 10
MWP bar 3
Capacity of Integrated Electric Heater kW 3.00
Note:
Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled water inlet temperature of 30°C and water outlet temperature of 35°C.
Specification are subjected to change without prior notice for further improvement.

7
2.2 WH-MHF12G6E5
Item Unit Refrigerant System
Performance Test Condition EN14511
Heating Capacity
Condition
(Ambient/Water) A7W35 A2W35
kW 12.00 12.00
BTU/h 41000 41000
kcal/h 10320 10320
COP W/W 4.46 3.26
kcal/hW 3.84 2.80
Air Flow m3/min (ft3/min) 80.0 (2830)
Refrigeration Control Device Expansion Valve
Refrigeration Oil cm3FV50S (1600)
Refrigerant (R407C) g (oz) 1.92k (67.8)
Compressor
Type Hermetic Motor / Rotary
Motor Type Brushless (4-poles)
Rated Output kW 3.40
Fan
Type Propeller Fan
Material PP
Motor Type DC (8-poles)
Input Power W —
Output Power W 60
Fan Speed rpm 510 (Top Fan) 550 (Bottom Fan)
Heat Exchanger
Fin material Aluminium (Pre Coat)
Fin Type Corrugated Fin
Row × Stage × FPI 2 × 51 × 18
Size (W × H × L) mm 903.7 × 1295.4 × 38.1
Item Unit Mono Bloc Unit
Dimension
Height mm (inch) 1410 (55-1/2)
Width mm (inch) 1283 (50-1/2)
Depth mm (inch) 320 (12-19/32)
Net Weight kg (lbs) 151 (333)
Noise Level dB-A 50
Power Level dB 67
Power Source (Phase, Voltage, Cycle)
ø Single
V 230
Hz 50
Input Power kW 2.69 3.68
Maximum Input Power For Mono Bloc Unit kW 6.20
Power Supply 1: Phase (ø) / Max. Current (A) / Max. Input Power (W) Single / 29.0 / 6.20k
Power Supply 2: Phase (ø) / Max. Current (A) / Max. Input Power (W) Single / 26.0 / 6.00k
Power Supply 3: Phase (ø) / Max. Current (A) / Max. Input Power (W) - / - / -
Starting Current A 12.8
Running Current A 12.8 17.2
Maximum Current For Mono Bloc Unit A 29.0
Power Factor % 93 93

8
Item Unit Mono Bloc Unit
Power factor means total figure of compressor and outdoor fan motor.
Power Cord Number of core -
Length m (ft) -
Thermostat Electronic Control
Protection Device Electronic Control
Item Unit Water System
Performance Test Condition EN14511
Operation Range Outdoor Ambient °C -20 ~ 35
Water Outlet °C 25 ~ 65
Internal Pressure Differential kPa 44.7
Water Pipe Diameter Inlet mm (inch) 30 (1-3/16)
Outlet mm (inch) 30 (1-3/16)
Water Drain Hose Inner Diameter mm (inch) 15.00 (19/32)
Pump
Motor Type DC Motor
No. of Speed 7 (Software Selection)
Input Power W 72
Hot Water Coil
Type Brazed Plate
No. of Plates 80
Size (W x H x L) mm 130 × 93 × 325
Water Flow Rate l/min (m3/h) 34.4 (2.1)
Pressure Relief Valve Water Circuit kPa Open: 300, Close: 265 and below
Flow Switch Magnetic Lead Switch
Protection Device A Residual Current Circuit Breaker (40)
Expansion Vessel Volume I 10
MWP bar 3
Capacity of Integrated Electric Heater kW 6.00
Note:
Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled water inlet temperature of 30°C and water outlet temperature of 35°C.
Specification are subjected to change without prior notice for further improvement.

9
3. Features
Inverter Technology
- Energy saving
High Efficiency
Compact Design
Environment Protection
- Non-ozone depletion substances refrigerant (R407C)
Easy to use remote control
Weekly Timer setting
Quality Improvement
- Random auto restart after power failure for safety restart operation
- Gas leakage protection
- Prevent compressor reverse cycle
- Inner protector to protect compressor
Serviceability Improvement
- Breakdown Self Diagnosis function
- System Status Check Buttons for servicing purpose
- System Service Mode Button for servicing purpose
- Front maintenance design for mono bloc unit
Operation Condition
Water outlet temperature (°C) Ambient temperature (°C)
HEATING Maximum 65 35
Minimum 25 -20
NOTICE : When the outdoor temperature is out of the above temperature range, the heating capacity will drop significantly
and mono bloc unit might stop for protection control.

10
4. Location of Controls and Components
4.1 Mono Bloc Unit
Air inlet (rear)
A
ir outlet
Air inlet (side)
Handle
(2 pieces front and 2 pieces behind)
Cabinet Front Plate
Top Plate

11
4.1.1 Main Components
2
7
10
8
1
13
10
6
3
4
11
12
5
A
14
9
a
b
Optional cord / cable :-
•
3-way Valve cable (3 x min 0.5mm
2
)
•
Booster Heater cord (3 x min 1.5mm
2
)
•
Room Themostat cable (4 or 3 x min 0.5mm
2
)
•
TankOLPcable(2xmin0.5mm
2
)
•
Tank Sensor cable (2 x min 0.3mm
2
)
•
External Controller cable (2 x min 0.5mm
2
)
•
Solar Three-way Valve cable (3 x min 0.5mm
2
)
•
Solar Pump Station cable (2 x min 0.5mm
2
)
Component name
1PCB
2Pressure relief valve
3Flow switch
4Pressure gauge
5Water pump
6RCCB
7Bushing
8Cabinet front plate
9Cabinet top plate
0Overload protector
aHeater assembly
bExpansion vessel
cCover
dAir purge valve
Connector name
g Water inlet
h Water outlet
(VIEW
WITHOUT
COVER)
DETAIL A g DETAIL A h
FOR
WH-MHF12G6E5
(WITHOUT OLP
COVER)
FOR
WH-MHF09G3E5
(WITHOUT OLP
COVER)
View without cabinet top plate
Ty p e
designation
60245 IEC
57 or heavier
cord/ cable
Remote Control
Power Supply 1
Power Supply 2
7

4.1.
2
4.1.
2
The u
1
2
3
4
5
7
8
2
Locati
o
Re
m
2
.1
ser interfac
e
910 11
o
n of Co
n
m
ote Con
t
e
allows the i
12 13
14
n
trol
t
ro
l
nstaller and
1
5
1
6
6
1
7
1
8
1
9
user to setu
p
OFF/O
N
This bu
t
Operat
i
This LE
Extern
a
This LC
Force
H
This ico
Backu
p
This ico
Quiet
M
This ico
Tank M
This ico
1
2
3
4
5
6
7
8
9
Heat M
o
This ico
Auto M
This ico
Solar
D
This LC
Cautio
n
This LC
Timer/
C
This LC
Outdo
o
This LC
Water
O
This LC
Backu
p
This ico
Booste
This ico
Syste
m
This ico
Syste
m
This ico
Syste
m
This ico
8
10
11
12
13
14
15
16
17
18
19
5
6
6
7
8
9
12
p, use and
m
N
Button
t
ton starts or
i
on LED
D indicates t
h
a
l Thermo C
o
D show the
e
H
eater Requ
e
n indicates f
o
p
Heater Ena
n indicates b
a
M
ode Indicat
o
n indicates q
ode Indicat
o
n indicates t
a
o
de OFF/ON
n indicates h
e
ode OFF/O
N
n indicates a
D
isplay
D show the
s
n
(Tank Tem
p
D show the
C
C
lock Settin
g
D show the
w
o
r Ambient T
D show the
o
O
utlet Temp
e
D show the
w
p
Heater Act
u
n indicates b
a
r Heater Act
n indicates b
o
m
Setting Mo
d
n indicates t
h
m
Status Che
c
n indicates t
h
m
Service Mo
n indicates t
h
m
aintain the
u
stops the m
o
h
e unit is in o
o
ntroller Co
n
e
xternal ther
m
e
st OFF/ON
I
o
rce heater r
e
bled/Disabl
e
a
ckup heate
r
o
r
uiet mode o
p
o
r
a
nk mode op
e
Indicator
e
ating mode
N
Indicator
uto mode O
F
s
olar display.
p
erature ab
o
C
aution displ
a
g
Display
w
eekly sched
u
emperature
o
utdoor ambi
e
e
rature Disp
w
ater outlet t
e
u
al (OFF/ON
)
a
ckup heate
r
ual (OFF/O
N
o
oster heate
r
d
e OFF/ON I
h
e system se
t
c
k Mode OF
h
e status che
c
de OFF/ON
I
h
e system se
r
u
nit.
o
de operation
peration.
n
nected Dis
p
m
o controller
c
I
ndicator
e
quest OFF/
O
e
d Indicator
r
enabled/dis
a
p
eration.
e
ration.
OFF/ON op
e
F
F/ON operat
i
o
ve 60°C) In
d
a
y.
u
le timer sett
Display
e
nt temperat
u
lay
e
mperature.
)
Indicator
r
actual (OFF
/
N
) Indicator
r
actual (OFF
ndicator
t
ting mode re
F/ON Indica
t
c
k mode req
u
I
ndicator
r
vice mode r
e
function of t
h
p
lay
c
onnected di
s
O
N mode op
e
a
bled mode
o
e
ration.
i
on.
d
icator
ing and cloc
k
u
re.
/
ON) operati
o
/ON) operati
o
quest OFF/
O
t
or
u
est OFF/ON
e
quest OFF/
O
h
e unit.
s
play.
e
ration.
o
peration.
k
display.
o
n.
o
n.
O
N display.
display.
O
N display.

13
4.1.3 To adjust initial settings
• The s
y
stem ma
y
not work properl
y
if set wron
g
l
y
. Please consult
Dealer
Select menus and determine settings according to the system available in the
household. It is recommended that all alterations of settings are done by an
authorised dealer or specialist.
• After initial installation,
y
ou ma
y
manuall
y
ad
j
ust the settin
g
s.
The initial setting remains active until the user changes it.
• The remote control can be used for multiple installations.
• Ensure the operation LED is OFF before settin
g
.
an authorised dealer.
1Press and simultaneously and hold for
5 seconds until the display shows SETTING STATUS.
2Press or to select the menu.
3Press to enter the menu.
4Press or to select YES/NO, or other options.
YES: to enable the menu
NO: to disable the menu
5Press to confirm.
Remote Control
DisplayOperation LED
Menu (1 ~ 17) Default
Setting
Setting
1
Room Thermostat Connection
To select whether or not to connect to the optional room
thermostat.
2
Backup Heater Selection
To reduce the heater power if unnecessary.
*Options of kW vary depending on the model.
9 kW *3 kW / 6 kW /
9 kW
3
Water System Freeze Prevention
To activate or deactivate the water freeze prevention when the
system is OFF.
4
Tank Connection
To select whether or not to connect to the optional water tank unit.
Note: If NO is selected, menus 5 to 15 are skipped.
5
Solar Priority
To select the use of solar panel for heating up the water tank.
6
Heating Priority
To select the room heating as priority during HEAT + TANK mode.
Note: If YES is selected, menus 7 and 8 are skipped for HEAT +
TANK mode.
7 Heating Operation Interval
To set the interval for HEAT mode during HEAT + TANK mode.
Note: If YES is selected in menu 6, this menu is skipped.
3 hours 0.5 hours ~
10 hours
8 Tank Heat-up Interval
To set the interval for the water tank during HEAT + TANK mode.
Note: If YES is selected in menu 6, this menu is skipped.
30 minutes 5 minutes ~
1 hour 35 minutes
Display
NO YES NO
NO YES NO
NO YES NO
NO YES NO
YES YES NO

14
YES YES NO
YES YES NO
NO YES NO
AAB
70 °C 40 °C ~ 75 °C
- 1 day ~ 99 days
The current day and time need to be set in cases below:•
- A long time has elapsed since the power was turned on the
9Booster Heater
To activate or deactivate the water tank’s booster heater.
Note: If NO is selected, menu 10 is skipped.
10 Booster Heater Delay Timer
To delay time for the booster heater to activate while the system is
heating up the water tank.
1 hour 20 minutes ~
1 hour 35 minutes
• Do not use the system during sterilisation in order to prevent scalding with hot water, or overheating of shower.
• Ask an authorised dealer to determine the level of sterilisation function field settings according to the local laws and
regulations.
11 Sterilisation
To sterilise the water tank, if required.
Note: If NO is selected, menus 12 to 14 are skipped.
12 Sterilisation Day & Time
To set timer for sterilisation.
(Only once a week. Operates even under a standby condition)
Monday
12:00
Monday ~ Sunday
0:00 ~ 23:50
13 Sterilisation Temperature
To set the temperature of sterilisation.
14 Continuation of Sterilisation
To maintain heating temperature in order to complete the
sterilisation.
10 minutes 5 minutes ~
1 hour
15 Base Pan Heater
To select whether or not to connect to the optional base pan
heater.
Note: If NO is selected, menu 16 is skipped.
16 Base Pan Heater type
Type A - The base pan heater activates only during deice
operation.
Type B - The base pan heater activates when outdoor ambient
temperature is 5 °C or lower.
17 Dry Concrete
During construction to dry the concrete under a preset
temperature.
Do not use this menu for any other purposes and in period other
than during construction (Refer to information page).
User
Remote control preparation
1Press .
2Press or to set the current day.
3Press to confirm.
423
■ Note:
- When the power is turned on for the first time.
last time.
• The current time that has been set will be the standard time for
all the timer operations.
Caution Indicator (Tank Temperature above 60 °C)
Dealer
Operation/settings to be done only by the authorised dealer/specialist.
User
Operation/settings to be done by the authorised dealer/specialist or user.
Repeat steps and to set the current time.

15
4.1.4 How to use
User
Enjoy quiet operation
Press .
• This operation reduces the noise of mono bloc unit.
The operation may cause heating ability to decrease.
User
System status check mode
1Press .
(The display shows STATUS.)
2Press or to check the selected mode.
• Dry concrete (does not show during normal
operation)
• The Water Inlet Temperature
• Tank Temperature
• Compressor Running Frequency
• Error History
• Heat mode total power consumption (Up to 999 days)
• Tank mode total power consumption (Up to 999 days)
• Press to exit the STATUS mode.
■ Note:
• Once the STATUS mode is entered, the display
shows STATUS.
• The STATUS mode cannot be activated when the
display shows SETTING.
• The total power consumption is an estimated value
based on AC 230 V and may differ from value
measured by precise equipment.
■
Note: In normal operation, the , and buttons are not in use.
User
Turn on or off the syste
m
Press .
W
hen the s
y
stem is ON, the operation LED is lit and the
actual water outlet temperature and outdoor ambient
t
emperature are shown on the displa
y
.
User
Select operation mode
Press to select operation mode.
HEAT turned ON or OFF.
• The mono bloc unit provides heat to the
• The panel/floor HEAT operation is either
system.
HEAT
+ TANK
• The mono bloc unit provides heat to the
sanitary water tank and the system.
• This mode can be selected only when the
sanitary water tank is installed.
TANK • The sanitary water tank is either turned
ON or OFF.
• The mono bloc unit provides heat to the
sanitary water tank.
User
Initiate the backup heater
Press .
• The backup heater provides extra heat at low outdoor
temperature. The backup heater is possible only in the
heat mode.
• Once the backup heater is set, it is automaticall
y
operated when conditions are fulfilled.
• To disable the backup heater, pres
s
again.
The system is turned off by an external switch.

16
User
Checking the temperature range
1Press and hold for 5 seconds to enter the temperature range setting mode.
2Press or to select a menu.
• Press to exit.
24 °C 5 °C ~ 35 °C
0 °C -15 °C ~ 20 °C
52 °C 40 °C ~ 75 °C
55 °C
35 °C
25 °C ~ 65 °C
25 °C ~ 65 °C
-5 °C -15 °C ~ 15 °C
15 °C -15 °C ~ 15 °C
Dealer
Operation/settings to be done only by the authorised dealer/specialist.
User
Operation/settings to be done by the authorised dealer/specialist or user.
Dealer
System temperature setting
Temperature settingDisplay
The system controls the temperature for each menu based on the
outdoor ambient temperature.
• To set or change the temperatures, make sure to contact your
nearest authorised dealer.
1Press and hold for 5 seconds to enter the
temperature range setting mode.
(The display shows SETTING.)
2Press or to select a menu.
3Press to enter the menu.
4Press or to set the desired temperature.
5Press to confirm the setting.
• Repeat steps 2to 5to set other menus.
Menu Default
setting
Temperature
setting Display
Setting of low outdoor ambient temperature.
HEAT
Setting of high outdoor ambient temperature.
Setting of water outlet temperature at low outdoor
ambient temperature.
Setting of water outlet temperature at high outdoor
ambient temperature.
During HEAT mode, the water
outlet temperature is adjusted as
is shown the diagram on the right.
It is performed within the preset
temperature range.
<Water outlet
temperature>
<Outdoor ambient temperature>
max. water temp.
min. water temp.
Setting of outdoor ambient temperature to turn
OFF heating operation during HEAT mode. HEAT
Setting of outdoor ambient temperature to turn ON
the backup heater. HEATER
Setting of sanitary water tank temperature. TANK

17
User
Shifting the water temperature
Desired temperature setting
This easily shifts the water outlet temperature if the setting is
undesirable.
1Press to enter the water temperature shifting mode.
2Press to change setting.
3Press or to set the desired temperature.
(temperature range: -5 °C ~ 5 °C)
Temperature setting
+5
-5
Shift value
<Water outlet
t
emperature
>
<Outdoor ambient temperature>
4Press to confirm the setting.
■
Note:
• Pres
s
or wait for 30 seconds to exit the SETTING mode.
• The set temperature will be saved in the system once confirmed.
• The SETTING mode cannot be activated when the SERVICE and STATUS indicators are ON.
• The system will shift the temperature within water outlet temperature range.
User
Holiday mode
• By setting the day (s) in holiday mode, it promotes energy savin
g
while you are on holiday, and enables the system to resume at the
preset temperature after your holiday.
• Ensure that the system is OFF before setting.
• The system will resume operation automatically at 00:00 am after
the holiday.
• The day the HOLIDAY mode was set is counted as day 1.
Desired days
Example:
Setting the holiday mode on June 21, 08:00 am. By setting 3 days,
t
he system resumes operation on June 24, 00:00 am.
1Press to enter the HOLIDAY mode.
2Press or to set the desired days.
(Setting range: 1 day ~ 999 days)
3Press to confirm the setting.
■
Note:
• Pres
s
or wait 30 seconds to exit the HOLIDAY mode.

18
User
Weekly timer setting
Promotes energy saving by allowing you to set up to 6
programmes in any given day.
Indicates the next timer operation
programme
Day to be selected
Indicates the next timer
operation day
Programme number in a day
OFF Timer
ON Timer
Lights up if Timer operation is selected
1Press to enter the timer setting mode.
2Press or to select your desired day.
3Press to confirm your selection.
4sserp,gniknilbeblliw”1“ to set
programme 1.
5Press to select ON or OFF timer.
6Press or to select your desired time.
You can set ,, and the Water
Temperature Thermo Shift setting.
7Press to confirm programme 1. The selected
day will be highlighted with ▼.
• After 2 seconds, the display will move to the next
programme. Repeat steps 4to 7to set
programmes 2 to 6.
• During timer setup, if no button is pressed within
30 seconds, or if the is pressed, the setting at
that moment is confirmed and timer setup is ended.
To check current timer programme
1Press to enter timer mode and press
to enter day setting.
2Press or until your desired day is shown,
press to confirm your selection.
3Press or to check the set programmes.
To modify current timer programme
or add new timer programme
1spetsmrofreP 1to 7of “Weekly timer
setting” to modify existing timer programme, or
add any timer programme.
To cancel current timer programme
1Press to enter day.
2Press or until your desired day is shown,
press to enter programme setting.
3Press or until your desired programme is
shown.
Press to cancel the programme and ▼will
disappear.
To disable/enable Weekly Timer
•To disable weekly timer setting, press , then
press .
•To enable previous weekly timer setting, press ,
then press .
Dealer
Operation/settin
g
s to be done onl
y
b
y
the authorised dealer/specialist.
User
Operation/settings to be done by the authorised dealer/specialist or user.
■
Note:
• You may set the timer for each day of the week (Monday to Sunday) with 6 programmes per day.
• When the system is switched on by the timer, it will use the previously set temperature to control the water outle
t
temperature.
• The same timer programme cannot be set on the same day.
• You may also select 2 or more days with the same timer setting.

19
Dry Concrete Function
• During construction to dry the concrete under a preset temperature.
1Press and simultaneously and hold for 5 seconds until the display shows “ ”.
2Press .
(The display shows “ ”.)
3Press
Press
to select day.
or to set the desired temperature.
4Press to confirm the selection.
5Repeat step 3and 4to set other days and temperature.
• Press to exit.
To Reset the Remote Control to Default
Setting
1Press , , continuously for 5 seconds. The
operation is off during this period.
2The display shows “ , , ” for 2
seconds for confirmation. After 2 seconds, it goes to
normal display.

20
5. Dimensions
5.1 Mono Bloc Unit
(579)
400 356
154
1410
615426.5
175
275
413
30
cc
70
277
320
152
1283
256 (30)
293
318.5
50
45 45 45
83.5
Unit: mm
<Top View>
<Front View>
<Back View>
<Side View><Side View>