Panasonic TH-L42S10R User manual

© Panasonic Corporation 2009. Unauthorized
copying and distribution is a violation of law
ORDER NO. MTV0901831CE
LCD TV
Model No. TH-L42S10R
Chassis: KM03
Destination: IRAN
Specifications
Power Source AC SINGLE 220 - 240V, 50/60 Hz
Power Consumption
Average use 199 W
Standby condition 0.7 W
Display panel
Aspect Ratio 16:9
Visible screen size 106 cm (diagonal)
930 mm (W) ×523 mm (H)
Number of pixels 2,073,600 (1,920 (W) ×1,080 (H))
Sound
Speaker Full range ×2 pcs, 8 Ω
Audio Output 20 W (10 W + 10 W), 10% THD
Headphones M3 (3.5 mm) stereo mini Jack ×1
PC Signals VGA, SVGA, XGA
SXGA ...... (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems / Band name 17 SYSTEMS FUNCTIONS
1PAL B, G, H
Reception of broadcast transmission and
playback from video cassette tape recorders.
2PAL I
3PAL D, K
4SECAM B, G
5SECAM D, K
6SECAM K1
7NTSC M (NTSC 3.58 / 4.5MHZ)

TH-L42S10R
2
8NTSC 4.43 / 5.5 MHz
Playback from special VCR’s or DVD.
9NTSC 4.43 / 6.0 MHz
10 NTSC 4.43 / 6.5 MHz
11 NTSC 3.58 / 5.5 MHz
12 NTSC 3.58 / 6.0 MHz
13 NTSC 3.58 / 6.5 MHz
14 SECAM I
15 PAL 60 Hz / 5.5 MHz Playback from Special Disc Players and
Special VCR’s or DVD.
16 PAL 60 Hz / 6.0 MHz
17 PAL 60 Hz / 6.5 MHz
Receiving Channels (Analogue TV)
VHF BAND 2 - 12 (PAL / SECAM B, K1)
0 - 12 (PAL B AUST.)
1 - 9 (PAL B N.Z.)
1 - 12 (PAL / SECAM D)
1 - 12 (NTSC M JAPAN)
2 - 13 (NTSC M USA)
UHF BAND 21 - 69 (PAL G, H, I / SECAM G, K, K1)
28 - 69 (PAL B AUST.)
13 - 57 (PAL D, K)
13 - 62 (NTSC M JAPAN)
14 - 69 (NTSC M USA)
CATV S1 - S20 (OSCAR)
1 - 125 (U.S.A. CATV)
C13 - C49 (JAPAN)
S21 - S41 (HYPER)
Z1 - Z37 (CHINA)
5A, 9A (AUST.)
Aerial - Rear VHF / UHF
Operating Conditions Temperature : 0°C - 40°C
Humidity : 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 Input AUDIO L-R RCA PIN Type ×2 0.5 V [rms]
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
COMPONENT Y 1.0 V[p-p] (including synchronization)
PB/CB, PR/CR± 0.35 V [p-p]
AV2 Input AUDIO L-R RCA PIN Type ×2 0.5 V [rms]
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
COMPONENT Y 1.0 V[p-p] (including synchronization)
PB/CB, PR/CR± 0.35 V [p-p]
AV3 Input AUDIO L-R RCA PIN Type ×2 0.5 V [rms]
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
S-VIDEO Mini DIN 4-pin Y: 1.0 V [p-p] (75 Ω) C: 0.286 V [p-p] (75 Ω)
Others HDMI 1 - 3 Input TYPE A Connectors • This TV supports “HDAVI Control 4” function.
PC Input HIGH-DENSITY D-SUB 15 PIN R, G, B / 0.7 V[p-p] (75 Ω)
HD, VD / TTL LEVEL 2.0-5.0 V [p-p] (high impedance)
Card Slot SD Card slot ×1
Monitor
Output AUDIO L-R RCA PIN Type ×2 0.5 V [rms] (High impedance)
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
Dimensions (W x H x D) 1,021 mm ×680 mm ×310 mm (With Pedestal)
1,021 mm ×637 mm ×115 mm (TV only)
Mass 23 kg Net (With Pedestal)
20 kg Net (TV only)
Design and specifications are subject to change without notice. Weight and dimensions shown are approximate.

TH-L42S10R
3
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 5
1.1. General Guidelines---------------------------------------- 5
1.2. Touch-Current Check------------------------------------- 5
1.3. KM03 Chasis Block Diagram--------------------------- 6
2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices------------------ 7
3 About Lead Free Solder (PbF) ------------------------------- 8
4 Power LED Blinking Timing----------------------------------- 9
5 Location of Controls and Components ------------------10
5.1. Wire Dressing ---------------------------------------------10
6 Disassembly and Assembly Instructions ---------------11
6.1. AC Cord Dressing----------------------------------------11
6.2. AC Cord Installation--------------------------------------12
6.3. LCD Panel Assembly Installation---------------------13
6.4. LED Panel Installation & Fitting-----------------------14
6.5. Control Panel Assembly And Installation-----------15
6.6. Side AV Assembly And Installation ------------------16
6.7. Speaker Installation--------------------------------------17
6.8. LCD Bracket And MTG Installation ------------------18
6.9. Chassis Frame - Screw---------------------------------19
6.10. PCB, Clamper And Screw Fixing---------------------20
6.11. VESA MTG Installation----------------------------------21
6.12. VESA Metal (Right) Installation-----------------------22
6.13. VESA (BC) Installation----------------------------------23
6.14. Back Cover Assembly-----------------------------------24
6.15. Pedestal Assembly 1 ------------------------------------25
6.16. Pedestal Assembly 2 ------------------------------------26
6.17. Pedestal Assembly 3 ------------------------------------27
6.18. Pedestal Assembly 4 ------------------------------------28
7 Service Mode Adjustment ------------------------------------29
7.1. Self Check Mode -----------------------------------------29
7.2. Hotel Mode Adjustment---------------------------------29
7.3. Hotel Mode-------------------------------------------------29
8 Measurements and Adjustments---------------------------30
8.1. Voltage Chart of A Board-------------------------------30
8.2. Voltage Chart of P Board-------------------------------30
9 Printed Circuit Board-------------------------------------------31
9.1. A-Board -----------------------------------------------------31
9.2. A-Board -----------------------------------------------------32
10 Schematic Diagram---------------------------------------------33
10.1. Schematic Diagram Notes -----------------------------33
10.2. A Board -----------------------------------------------------34
10.2.1. A Board - Sheet : 001 (1 / 1)----------------------34
10.2.2. A Board - Sheet : 002 (1 / 8)----------------------35
10.2.3. A Board - Sheet : 002 (2 / 8)----------------------36
10.2.4. A Board - Sheet : 002 (3 / 8)----------------------37
10.2.5. A Board - Sheet : 002 (4 / 8)----------------------38
10.2.6. A Board - Sheet : 002 (5 / 8)----------------------39
10.2.7. A Board - Sheet : 002 (6 / 8)----------------------40
10.2.8. A Board - Sheet : 002 (7 / 8)----------------------41
10.2.9. A Board - Sheet : 002 (8 / 8)----------------------42
10.2.10. A Board - Sheet : 003 (1 / 4) ---------------------43
10.2.11. A Board - Sheet : 003 (2 / 4) ---------------------44
10.2.12. A Board - Sheet : 003 (3 / 4) ---------------------45
10.2.13. A Board - Sheet : 003 (4 / 4) ---------------------46
10.2.14. A Board - Sheet : 004 (1 / 4) ---------------------47
10.2.15. A Board - Sheet : 004 (2 / 4) ---------------------48
10.2.16. A Board - Sheet : 004 (3 / 4) ---------------------49
10.2.17. A Board - Sheet : 004 (4 / 4) ---------------------50
10.2.18. A Board - Sheet : 005 (1 / 5) ---------------------51
10.2.19. A Board - Sheet : 005 (2 / 5) ---------------------52
10.2.20. A Board - Sheet : 005 (3 / 5) ---------------------53
10.2.21. A Board - Sheet : 005 (4 / 5) ---------------------54
10.2.22. A Board - Sheet : 005 (5 / 5) ---------------------55
10.2.23. A Board - Sheet : 006 (1 / 6) ---------------------56
10.2.24. A Board - Sheet : 006 (2 / 6) ---------------------57
10.2.25. A Board - Sheet : 006 (3 / 6) ---------------------58
10.2.26. A Board - Sheet : 006 (4 / 6) ---------------------59
10.2.27. A Board - Sheet : 006 (5 / 6) ---------------------60
10.2.28. A Board - Sheet : 006 (6 / 6) ---------------------61
10.2.29. A Board - Sheet : 007 (1 / 2) ---------------------62
10.2.30. A Board - Sheet : 007 (2 / 2) ---------------------63
10.2.31. A Board - Sheet : 008 (1 / 6) ---------------------64
10.2.32. A Board - Sheet : 008 (2 / 6) ---------------------65
10.2.33. A Board - Sheet : 008 (3 / 6) ---------------------66
10.2.34. A Board - Sheet : 008 (4 / 6) ---------------------67
10.2.35. A Board - Sheet : 008 (5 / 6) ---------------------68
10.2.36. A Board - Sheet : 008 (6 / 6) ---------------------69
10.2.37. A Board - Sheet : 009 (1 / 4) ---------------------70
10.2.38. A Board - Sheet : 009 (2 / 4) ---------------------71
10.2.39. A Board - Sheet : 009 (3 / 4) ---------------------72
10.2.40. A Board - Sheet : 009 (4 / 4) ---------------------73
10.2.41. A Board - Sheet : 010 (1 / 9) ---------------------74
10.2.42. A Board - Sheet : 010 (2 / 9) ---------------------75
10.2.43. A Board - Sheet : 010 (3 / 9) ---------------------76
10.2.44. A Board - Sheet : 010 (4 / 9) ---------------------77
10.2.45. A Board - Sheet : 010 (5 / 9) ---------------------78
10.2.46. A Board - Sheet : 010 (6 / 9) ---------------------79
10.2.47. A Board - Sheet : 010 (7 / 9) ---------------------80
10.2.48. A Board - Sheet : 010 (8 / 9) ---------------------81
10.2.49. A Board - Sheet : 010 (9 / 9) ---------------------82
10.2.50. A Board - Sheet : 011 (1 / 4)----------------------83
10.2.51. A Board - Sheet : 011 (2 / 4)----------------------84
10.2.52. A Board - Sheet : 011 (3 / 4)----------------------85
10.2.53. A Board - Sheet : 011 (4 / 4)----------------------86
10.2.54. A Board - Sheet : 012 (1 / 2) ---------------------87
10.2.55. A Board - Sheet : 012 (2 / 2) ---------------------88
10.2.56. A Board - Sheet : 013 (1 / 5) ---------------------89
10.2.57. A Board - Sheet : 013 (2 / 5) ---------------------90
10.2.58. A Board - Sheet : 013 (3 / 5) ---------------------91
10.2.59. A Board - Sheet : 013 (4 / 5) ---------------------92
10.2.60. A Board - Sheet : 013 (5 / 5) ---------------------93

TH-L42S10R
4
10.2.61. A Board - Sheet : 014 (1 / 2)----------------------94
10.2.62. A Board - Sheet : 014 (2 / 2)----------------------95
10.2.63. A Board - Sheet : 015 (1 / 5)----------------------96
10.2.64. A Board - Sheet : 015 (2 / 5)----------------------97
10.2.65. A Board - Sheet : 015 (3 / 5)----------------------98
10.2.66. A Board - Sheet : 015 (4 / 5)----------------------99
10.2.67. A Board - Sheet : 015 (5 / 5)-------------------- 100
10.2.68. A Board - Sheet : 016 (1 / 5)-------------------- 101
10.2.69. A Board - Sheet : 016 (2 / 5)-------------------- 102
10.2.70. A Board - Sheet : 016 (3 / 5)-------------------- 103
10.2.71. A Board - Sheet : 016 (4 / 5)-------------------- 104
10.2.72. A Board - Sheet : 016 (5 / 5)-------------------- 105
10.3. K Board--------------------------------------------------- 106
10.3.1. K Board (1 / 2)-------------------------------------- 106
10.3.2. K Board (2 / 2)-------------------------------------- 107
10.4. P Board--------------------------------------------------- 108
10.4.1. P Board (1 / 4)-------------------------------------- 108
10.4.2. P Board (2 / 4)-------------------------------------- 109
10.4.3. P Board (3 / 4)---------------------------------------110
10.4.4. P Board (4 / 4)---------------------------------------111
10.5. V Board----------------------------------------------------112
10.5.1. V Board (1 / 4)---------------------------------------112
10.5.2. V Board (2 / 4)---------------------------------------113
10.5.3. V Board (3 / 4)---------------------------------------114
10.5.4. V Board (4 / 4)---------------------------------------115
11 Exploded View and Replacement Parts List --------- 116
11.1. Exploded View and Mechanical Replacement
Parts List --------------------------------------------------116
11.2. Electrical Replacement Parts List-------------------116
11.2.1. Replacement Parts List Notes ------------------116
11.2.2. Electrical Replacement Parts List--------------117

TH-L42S10R
5
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.2. Touch-Current Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground
such as a water pipe as shown in Figure 1.
3. Use the Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4. Check each exposed metallic part and measure the voltage at each point.
5. The potential at any point (touch current) expressed as voltage U1and U2, do not exceed the following values:
For AC: U1= 35 V (peak) and U2= 0.35 V (peak);
For DC: U1= 1.0 V,
NOTE :
The limit value of U2= 0.35 V (peak) for AC and U1= 1.0 V for DC correspond to the values 0.7 mA (peak) AC and 2.0 mA
DC.
The limit value U1= 35 V (peak) for AC correspond to the value 70 mA (peak) AC for frequencies greater than 100 kHz.
6. Should a measurement be out of the limits specified, there is a possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the customer.

TH-L42S10R
6
1.3. KM03 Chasis Block Diagram
TUNER
PWB
Hong Kong Digital
FE
S(5 or 6)/3.3
SDRAM
TUNER
TS
Parallel
ON Fix (Hard)
S5V
CI
POWER
-
SW
P>CI_POWER_ON P<CI_OCP
S3.3/1.8/1.2
M_SND
S5
M3.3
S3.3
S3.3
S3.3
AV-SW
R2A11014FT
Video
Audio
SW
SLV[90]
HD/VD/FBK
MUTE
STB_XRST
5VS/STB5/S5/DTV12
S3.3
10MHz
S3.3 S3.3
S3.3/S5
S3.3 S3.3/S5
P> FE_SW
Opt
Digital OUT
CVBS
S3.3/S1.8
S9/S5
HP
AMP
MAIN
AMP
AV-OUT
MONITOR
OUT
CVBS
L/R
HP_OUT
L/R
AV-IN
YUV
CVBS/S
L/R
YUV
CVBS/S
L/R
CVBS
L/R
PC
RGB
HS/VS
ADV7470
SLV[40,etc]
HDMI-Rx *4
AD-IN
Y/CVBS
Pb/C Pr
RGB_CVBS
SOY
RGB_FB
PC_HS
PC_VS
INT
ADV_RESET
SIF
S3.3/S1.8
HDMI
G>HPD
G<5V_DET
G<CEC
AV_L/R
MONITOR_OUT
L/R
AM
TV_L/R
L/R
L/R
L/R
MAIN
VIDEO
TU-CVBS
FE
WJCE6553
SLV[1E]
S5/S30
TUNER
SW1/2
mono
SIF
IF AGC
IF
PWM_OUT *1
Opt
CI
Card
TS
SW
3.3-5V
Level
Shift
TS
Buffer
CI
ASIC
#WE/#RE
#IOWR/#IORD #REG Buffer Ctrl
#CD #IREQ #WAIT
Peaks-AVC
31mm
IIC0
IIC1
IIC2
IIC3
G> AUDIO_XRST
IRQ3
74.25MHz
27MHz
27MHz
12MHz → nonuse
25MHz → for LAN9118
ICS
CLKGEN
w/t
VCXO
S1.8
TS
Serial
TS
Parallel
HSDIN
VI1CLKOUT
RGB 30bit
H,V,CLK APort
Video DAC
IECOUT
Audio
Discription
I2S I2S
RTL8100
CL-LF
Reset
25MHz
From CLKGEN
Ether
Connecter
ADDR &DATA
32bit +4bit
EEP
1k
S3.3
Analog ASIC
BD8651
GenX8
SLV[70]
SBO2 SBI2
EEPWP
IIC_1
SD-BOOT
STB3.3
EEP 8k
SLV[A0}
STB3.3
Support cardconnect or
NACE,CE1 CLE1 ALE1 WE1
WP BYRE1
NOR Flash
256Mbit
XRST
CS0
S3.3
STB3.3
OUT
RESET
HP
G> ADV_XRST
LVDS-1st
LVDS-2nd
USB-IF
TS Parallel
PWMA PWMK
LOSD
G> DTV_VOUTENB
AVC System MW: NONE SD: ONBOARD
SD-IF
BLUE-LED: NONE
S3.3
EEP 16k
SLV[A0}
S3.3
TEMP SENSE
SLV[A0}
RMT/ KEY V-PWB
STB3.3/S5
G> SD_LED_ON
G> G_LED_ON
G> R_LED_ON
G> ACTIVE_STBY_LED_ON
G< RMIN G< AI_SENSOR
G< KEY1
PCI BUS /VOUT
IS0 CH0
FS
NONE
OVP SOS G>MON_MUTE
G>SP_HP_MUTE
AMP/HP_MUTE
MONITOROUT_MUTE
G< TV_SOS
P> CI_XRST
P> EEPROM_WP
G> EEPROM_WP
Peaks_XRST
Peaks POWER_DET
RESET
POWER_DET
G>DTV_XRST
G>SW_OFF_DET
DDR2
800MHz
DDR2
800MHz
CPU BUS
ADDRESS EA[25:24], EA[7:0]
DATA ED[15:0]
Bport / ADDRESS EA[23:8]
YC 16bit
H,V,CLK
ADDRESS
EA[25:0]
DATA
ED[15:0]
ADDRESS
EA[7:1]
DATA
ED[7:0}
ADDRESS
CI_EA[15:1]
DATA
CI_ED[7:0]
5-3.3V
Level
Shift
P> XETS_CI
S3.3/S5
P> FE1_IRQ
P< FE_XRST
P> FE_IRQ P< FE_XRST
AMP/HP_MUTE
(G>SP_HP_MUTE)
MONITOROUT_MUTE
(G>MON_MUTE)
PWMA PWMK
G>PWM_POW_ON
G<INVERTER_SOS LVDS Dual
PWM
ADIM
Filter
M9
LCD PANEL
G>INVERTER_ON G>PANEL_TEST_ON
PNL_VCC
ADV
IIC
ADAV
IIC
24.576MHz to ADAV Block
ADV CLK from ADAV MCLK out
ADAV
MCLK
ADV CLK
30MHz
30.4MHz
TS Serial
TS
Parallel
IIC_0
L/R
SP
G<SOUND_SOS AMP/HP_MUTE
(G>SP_HP_MUTE)
SD-IF
NAND-IF
S3.3
NAND Flash
DATA
ED[7:0]
XNFCE,XNFWE,XNFRE
NFALE,NFCLE,XNFWP
NANDRYBY
S3.3
SD
Card
EA[23:8] ED[15:0]
G> ADV_XRST
ADAV_RESET
PWM OUT *2
HP_OUT
PWM_READY
SPDIF_OUT
SPDIF_IN
DTV_I2S_IN
HDMI_I2S_SPDIF
OUT/IN

TH-L42S10R
7
2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-
effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the
incidence of component damage caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminium foil to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it (most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or
comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices (otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).

TH-L42S10R
8
3 About Lead Free Solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead Solder and PbF will refer to Lead Free Solder.
The Lead Free Solder (PbF) used in our manufacturing process and discussed below is (Sn+Ag+Cu).
Those are Tin (Sn), Silver (Ag) and Copper (Cu), although other types are available.
This model uses PbF in its manufacture due to environmental conservation issues. For service and repair work, we would suggest
the use of PbF as well, although Pb may be used.
PCBs manufactured using lead-free will have the “PbF within a leaf Symbol” stamped on their back.
Caution
• PbF has a higher melting point than that of standard solder. Typically the melting point is 50 ~ 70°F (30~40°C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20°F (370 ± 10°C).
• PbF will tend to splash when heated too high (about 1100°F or 600°C).
If you must use Pb solder, please completely remove all of the PbF on the pins or solder area before applying Pb. If this is not
practical, be sure to heat the PbF until it melts, before applying Pb.
• After applying PbF to double layered boards, please check the component side for excess solder which may flow onto the
opposite side (see Figure 2).
Figure 2
Suggested PbF
There are several kinds of PbF available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu
(tin, copper) and Sn+Zn+Bi (tin, zinc, bismuth) solders can also be used.
Figure 3

TH-L42S10R
9
4 Power LED Blinking Timing
1. Subject
Information of LED Flashing timing.
2. Contents
When an abonormality has occurred in the unit, the protection circuits operates and reset to standby mode. At this time, the
defective block can be identified by the number of blinking of the Power LED on the front panel of the unit as follow:
Blinking times Contents
1 Inverter_SOS
3 SOS_3.3V over voltage protection
4 DTV_ 9V decreased / short circuit, main convertor stop detection.
5 Main_ 9V decreased
6 Sub_ 5V decreased
7 Sub_ 3.3V decreased
8 MAIN_ 3.3V decreased
9 Sound_ SOS
13 Emergency SOS
14 Audio PWM SOS

TH-L42S10R
10
5 Location of Controls and Components
5.1. Wire Dressing
1. Wiring No.1 ~ No.7
2. Remove dust of terminal of LVDS and PB connector. (by ion blow)
Wire Clamper
12345678910111213141516
No.1 A10 ~ V10
No.2 A01 ~ K01
No.3 A12 ~ SP(R)
No.4 A12 ~ SP(L)
No.5 INV (L) ~ P3
No.6 INV (R) ~ P2
No.7 INV (R) ~ A20

TH-L42S10R
11
6 Disassembly and Assembly Instructions
6.1. AC Cord Dressing
1. Clamp plug with clamper.
2. Insert beads 3pcs. And slide down to lower hole.
3. Stick the FILAMENT TAPE.

TH-L42S10R
12
6.2. AC Cord Installation
1. Put on the AC CORD BRACKET on the CABINET.
2. Fix the AC CORD BRACKET with SCREW.
3. Insert AC CORD connector into P-PCB connector.
4. Clamp the AC CORD.
5. Insert AC CORD bushing into the AC CORD BRACKET.
6. AC code is pushed into the bottom of the bracket.

TH-L42S10R
13
6.3. LCD Panel Assembly Installation
Put LCD panel on the cabinet.

TH-L42S10R
14
6.4. LED Panel Installation & Fitting
1. Put LED SHADE RIB on CABINET.
2. Fix LED PANEL on CABINET.
3. Wire connecting. (V10)
4. Put V-PCB on CABINET.
5. Fix them with SCREW.
6. Insert the CLAMPER.

TH-L42S10R
15
6.5. Control Panel Assembly And Installation
1. Wire connecting. (K1)
2. Assemble POWER BUTTON to the K-PRINT.
3. Assemble K-PRINT, CONTROL BUTTON, CONTROL PANEL BRACKET.
4. Fix them with SCREWS.
5. Stick the FELT.
1. Put control panel Assy on the cabinet.
2. Fix the control panel with screws.

TH-L42S10R
16
6.6. Side AV Assembly And Installation
1. Stick the side av indi. Sheet on the side av bracket.
2. Insert the SIDE AV BRACKET from the side position of the A-PCB.
3. Fix the SCREW with A-PB-MTG METAL.

TH-L42S10R
17
6.7. Speaker Installation
1. Stick the SP sponge.
2. SP bracket put on cabinet.
3. Fix them with screws.
4. Insert the SP rubber bush into the SP unit.
5. Insert the SP unit to SP bracket.

TH-L42S10R
18
6.8. LCD Bracket And MTG Installation
1. MASK BRACKET(SIDE/TOP/BTM) on the CABINET.
2. LCD BTM MTG on the CABINET.
3. Fix them with SCREW.

TH-L42S10R
19
6.9. Chassis Frame - Screw
1. Put on the CHASSIS FRAME on the LCD.
2. Fix them with screws.

TH-L42S10R
20
6.10. PCB, Clamper And Screw Fixing
1. Put on the P-PCB, A-PCB on the CHASSIS FRAME.
2. Fix them with screws.
3. Insert the clampers.