Panasonic TH-65PF9UK User manual

©2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
TH-65PF9UK
GPF9D Chassis
High Definition Plasma Display
Specifications
Power Source 120 V
A
C, 50 / 60Hz
Power Consumption
Power on 790 W
Stand-b
y
condition Save OFF 1.0 W, Save ON 0.8 W
Power off condition 0.1 W
Plasma Displa
y
panel Drive method:
A
C type 65-inch, 16:9 aspect ratio
Contrast Ratio Ma
x
5000:1
Screen size 56.5” (1,434 mm) (W) × 31.8” (807 mm) (H) × 65” (1,646 mm) (diagonal)
(No. of pixels) 2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots]
Operating condition
Temperature 32 °F - 104 °F (0 °C - 40 °C)
Humidit
y
20 % - 80 %
Applicabl
e
signals
Color System NTSC, PAL, PAL60, SECAM, Modified NTSC
Scanning format 525 (480) / 60i 60p, 625 (575)
/
50i 50p, 750 (720)
/
60p 50p, 1125 (1080) / 60i 50i 24p 25p
30p 24sF .... SMPTE274M, 1250 (1080) / 50i
PC signals VGA, SVGA, XGA, SXGA,
UXGA ..... (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
DVI-D Video Input DVI-D 24 Pin × 1
compliance with DVI Revision 1.0
A
udio Input Stereo mini
j
ack (M3) × 1
0.5Vrms
Content Protection Compatible with HDCP 1.1
COMPONENT / RGB
Y
/ G (BNC)
Y
or G with
/
syn
c
1.0 Vp-p (75 Ω)
PB/ B (BNC), PR
/
R (BNC) 0.7 Vp-p (75 Ω)
ORDER NO. MTNC060805CE
B34 Canada:D10

1 Applicable signals 4
2 Safety Precautions 5
2.1. General Guidelines 5
3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 6
4 About lead free solder (PbF) 7
5 Service Hint 8
6 Disassembly 9
6.1. Removal of the Back Cover 9
6.2. Removal of the HA-Board 9
6.3. Removal of the HDD-Board 9
6.4. Removal of the DS-Board 9
6.5. Removal of the HX-Board 10
6.6. Removal of the PB-Board 10
6.7. Removal of the DN-Board 10
6.8. Removal of the D-Board 10
6.9. Removal of the P-Board 11
6.10. Removal of the SU-Board and the SD-Board 11
6.11. Removal of the SC-Board 12
6.12. Removal of the SS2-Board and the SS3-Board 12
6.13. Removal of the SS-Board 12
6.14. Removal of the H3-Board (L), (R) 13
6.15. Removal of the C1, C2, C3, C4, C5 and the C6-Board 14
6.16. Removal of the Fan 16
6.17. Removal of the S1-Board, the V1-Board, the Power Button
and the Hinge Button 17
6.18. Removal of the Escutcheon and the Front Glass 18
6.19. Removal of the Plasma Panel 19
7 Location of Lead Wiring 23
8 Adjustment Procedure 25
8.1. Driver Set-up 25
8.2. Initialization Pulse Adjust 26
8.3. P.C.B. (Printed Circuit Board) Remove 26
8.4. Adjustment Volume Location 27
8.5. Test Point Location 27
9 Service mode 28
9.1. CAT (computer Aided Test) mode 28
9.2. IIC mode structure (following items value is sample data)
32
10 Adjustment 33
10.1. RGB white balance adjustment 33
10.2. HD white balance adjustment 35
10.3. Power control adjustment 37
11 Trouble shooting guide 38
A
UDIO IN (RCA PIN JACK × 2) 0.5 Vrms
PC (HIGH-DENSIT
Y
Mini D-SUB 15PIN)
Y
or G with
/
syn
c
1.0 Vp-p (75 Ω)
Y
or G without
/
syn
c
0.7 Vp-p (75 Ω)
B
/
PB
/
CB:0.7 Vp-p (75 Ω)
R
/
PR
/
CR:0.7 Vp-p (75 Ω)
HD
/
VD:1.0 - 5.0 Vp-p (high impedance)
VBS (use HD port) with
/
picture 1.0 Vp-p (high impedance)
without
/
picture 0.3 Vp-p (high impedance)
A
UDIO IN (M3 JACK) 0.5 Vrms
SERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) RS-232C COMPATIBLE
SPEAKERS (8Ω) 20 W [10 W + 10 W] (10 % THD)
Accessories Supplied
Remote Control Transmitter EUR7636070R
Batteries 2×
AA
Size
Fixing bands (TMME203 or TMME187) × 2
Dimensions (
W
×H×D) 61.2” (1,554 mm) × 36.4” (925 mm) × 3.9” (99 mm)
(excluding handle portion)
Mass (weight)
main unit onl
y
approx. 163.1 lbs
with speakers approx. 172.8 lbs
Notes:
· Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
CONTENTS
Page Page
2
TH-65PF9UK

11.1. Self Check 38
11.2. No Power 40
11.3. No Picture 40
11.4. Local screen failure 41
12 Option Setting 42
13 Conductor Views 45
13.1. P-Board 45
13.2. PB-Board 51
13.3. HA-Board 52
13.4. HX-Board 53
13.5. HDD-Board 54
13.6. H3, V1 and S1-Board 56
13.7. DS-Board 57
13.8. DN-Board 59
13.9. D-Board 61
13.10. C1-Board 63
13.11. C2-Board 64
13.12. C3-Board 65
13.13. C4-Board 66
13.14. C5-Board 67
13.15. C6-Board 68
13.16. SC-Board 69
13.17. SU-Board 72
13.18. SD-Board 73
13.19. SS-Board 74
13.20. SS2 and SS3-Board 77
14 Block and Schematic Diagram 79
14.1. Schematic Diagram Notes 79
14.2. Main Block Diagram 80
14.3. P-Board (1 of 2) Block Diagram 81
14.4. P-Board (2 of 2) Block Diagram 82
14.5. P-Board (1 of 2) Schematic Diagram 83
14.6. P-Board (2 of 2) Schematic Diagram 84
14.7. PB and V1-Board Block and Schematic Diagram 85
14.8. HA-Board Block and Schematic Diagram 86
14.9. HX-Board Block and Schematic Diagram 87
14.10. HDD-Board Block Diagram 88
14.11. HDD-Board (1 of 2) Schematic Diagram 89
14.12. HDD-Board (2 of 2) Schematic Diagram 90
14.13. DS-Board (1 of 2) and H3-Board Block Diagram 91
14.14. DS-Board (2 of 2) Block Diagram 92
14.15. DS-Board (1 of 3) and H3-Board Schematic Diagram 93
14.16. DS-Board (2 of 3) Schematic Diagram 94
14.17. DS-Board (3 of 3) Schematic Diagram 95
14.18. DN-Board (1 of 3) Block Diagram 96
14.19. DN-Board (2 of 3) Block Diagram 97
14.20. DN-Board (3 of 3) Block Diagram 98
14.21. DN-Board (1 of 10) Schematic Diagram 99
14.22. DN-Board (2 of 10) Schematic Diagram 100
14.23. DN-Board (3 of 10) Schematic Diagram 101
14.24. DN-Board (4 of 10) Schematic Diagram 102
14.25. DN-Board (5 of 10) Schematic Diagram 103
14.26. DN-Board (6 of 10) Schematic Diagram 104
14.27. DN-Board (7 of 10) Schematic Diagram 105
14.28. DN-Board (8 of 10) Schematic Diagram 106
14.29. DN-Board (9 of 10) Schematic Diagram 107
14.30. DN-Board (10 of 10) Schematic Diagram 108
14.31. D-Board (1 of 2) Block Diagram 109
14.32. D-Board (2 of 2) Block Diagram 110
14.33. D-Board (1 of 8) Schematic Diagram 111
14.34. D-Board (2 of 8) Schematic Diagram 112
14.35. D-Board (3 of 8) Schematic Diagram 113
14.36. D-Board (4 of 8) Schematic Diagram 114
14.37. D-Board (5 of 8) Schematic Diagram 115
14.38. D-Board (6 of 8) Schematic Diagram 116
14.39. D-Board (7 of 8) Schematic Diagram 117
14.40. D-Board (8 of 8) Schematic Diagram 118
14.41. C1, C2, C5 and C6-Board Block Diagram 119
14.42. C2, C3, C4 and C5-Board Block Diagram 120
14.43. C1-Board (1 of 2) Schematic Diagram 121
14.44. C1-Board (2 of 2) Schematic Diagram 122
14.45. C2-Board (1 of 2) Schematic Diagram 123
14.46. C2-Board (2 of 2) Schematic Diagram 124
14.47. C3-Board (1 of 2) Schematic Diagram 125
14.48. C3-Board (2 of 2) Schematic Diagram 126
14.49. C4-Board (1 of 2) Schematic Diagram 127
14.50. C4-Board (2 of 2) Schematic Diagram 128
14.51. C5-Board (1 of 2) Schematic Diagram 129
14.52. C5-Board (2 of 2) Schematic Diagram 130
14.53. C6-Board (1 of 2) Schematic Diagram 131
14.54. C6-Board (2 of 2) Schematic Diagram 132
14.55. SC-Board Block Diagram 133
14.56. SC-Board (1 of 4) Schematic Diagram 134
14.57. SC-Board (2 of 4) Schematic Diagram 135
14.58. SC-Board (3 of 4) Schematic Diagram 136
14.59. SC-Board (4 of 4) Schematic Diagram 137
14.60. SU and SD-Board Block Diagram 138
14.61. SU-Board (1 of 3) Schematic Diagram 139
14.62. SU-Board (2 of 3) Schematic Diagram 140
14.63. SU-Board (3 of 3) Schematic Diagram 141
14.64. SD-Board (1 of 3) Schematic Diagram 142
14.65. SD-Board (2 of 3) Schematic Diagram 143
14.66. SD-Board (3 of 3) Schematic Diagram 144
14.67. SS, S1, SS2 and SS3-Board Block Diagram 145
14.68. SS-Board (1 of 2) and S1-Board Schematic Diagram 146
14.69. SS-Board (2 of 2), SS2 and SS3-Board Schematic
Diagram 147
15 Parts Location 149
15.1. Exploded View 149
15.2. Cable relation 151
15.3. Packing summary 152
16 Mechanical Replacement Parts List 153
17 Replacement Parts List 154
17.1. Replacement Parts List Notes 154
17.2. Electrical Replacement Parts List 155
3
TH-65PF9UK

1 Applicable signals
4
TH-65PF9UK

2.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two
prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinet
part on the equipment such as screwheads, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between
1MΩand 5.2MΩ.
When the exposed metal does not have a return path to
the chassis, the reading must be .
Figure 1
2.1.2. Leakage Current Hot Check (See
Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF
capacitors, between each exposed metallic part on the set
and a good earth ground such as a water pipe, as shown in
Figure 1.
3. Use an AC voltmeter, with 1000 ohms / volt or more
sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Shimpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1 / 2 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the
customer.
2 Safety Precautions
2.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
5
TH-65PF9UK

3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder Remove device. Some solder Remove devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
6
TH-65PF9UK

4 About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol stamped on the back of PCB.
Caution
· Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
· Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
· After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto
the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
7
TH-65PF9UK

5 Service Hint
Board Name Function Board Name Function
D Digital Signal Processor,
Format Converter,
Plasma AI Processor
C4 Data Drive (Lower Left)
C5 Data Drive (Lower Center)
C6 Data Drive (Lower Right)
DS Slot Interface (Audio / Video / Sync Input
Switch),
SYNC Processor, Audio Processor,
Speaker Out Amplifier,
DC-DC Converter
H3 Speaker Terminal
S1 Power Switch
SS2 Sustain Out (Upper)
SS3 Sustain Out (Lower)
SS Sustain Drive V1 LED (Stand-By / Power On) & Remote
Receiver, Key Scan
SC Scan Drive PB Fan Control
SU Scan Out (Upper) P Line Filter, Power Supply
SD Scan Out (Lower) HX PC / RS-232C
C1 Data Drive (Upper Right) HA BNC Component Video
C2 Data Drive (Upper Center) DN Dital Signal Processor, Micon
C3 Data Drive (Upper Left) HDD DVI-D Terminal
Note:
Extension cable kit for Slot Board is supplied as service fixtures and tools.
(Part No. TZSC07040)
8
TH-65PF9UK

6 Disassembly
· To disassemble P.C.B., wait for 1 minute after power was
off for discharge from electrolysis capacitors.
· and marks indicate screw positions.
6.1. Removal of the Back Cover
1. Remove the screws (×9 , ×12 , ×15 ,×4 ) and then
remove the Back Cover.
6.2. Removal of the HA-Board
1. Remove the 4 screws (A) and then remove the HA Terminal
Block.
2. Remove the 4 screws (B).
3. Remove the 2 screws (C) and then remove the HA-Board.
6.3. Removal of the HDD-Board
1. Remove the 4 screws (D) and then remove the HDD
Terminal Block.
2. Remove the 4 screws (E).
3. Remove the 2 Hexagonal-Head screws (F) and then
remove the HDD-Board.
6.4. Removal of the DS-Board
1. Remove the HA Terminal Block and the HDD Terminal
Block.
(Reference to Removal of the HA-Board and the HDD-
Board)
2. Remove the flexible cables from the couplers (DS1, DS6).
3. Disconnect the couplers (DS2, DS3, DS4, DS7, DS8,
DS10, DS14, DS15, DS30).
4. Remove the 4 screws and then remove the Slot Case.
9
TH-65PF9UK

5. Remove the 9 screws and then remove the DS-Board and
Fixed Plate.
6.5. Removal of the HX-Board
1. Remove the HA Terminal Block and the HDD Terminal
Block.
(Reference to Removal of the HA-Board and the HDD-
Board)
2. Remove the 4 screws and then remove the Slot Block
Case.
3. Remove the 4 Hexagonal-Head screws (G) and the 2
screws of the HX-Board and then remove the HX-Board.
6.6. Removal of the PB-Board
1. Disconnect the couplers (PB30, PB31, PB32, PB33, PB34,
PB35, PB36, PB38).
2. Remove the 2 screws and then remove the PB-Board.
6.7. Removal of the DN-Board
1. Remove the flexible cables from the couplers (DN1, DN6).
2. Disconnect the couplers (DN2, DN3, DN51).
3. Remove the 4 screws and then remove the DN-Board.
6.8. Removal of the D-Board
1. Remove the PB-Board. (Reference to Removal of the PB-
Board)
2. Remove the flexible cables from the couplers (DN1, DN6).
3. Disconnect the couplers (D3, D5, D20, DN3).
4. Remove the 4 screws and then remove the DN-Board
Block.
10
TH-65PF9UK

5. Disconnect the coupler(D25).
6. Remove the flexible cables from the couplers (D31, D32,
D33, D34, D35, D36).
7. Remove the 4 screws and then remove the D-Board.
6.9. Removal of the P-Board
Please exchange fuse (F1601,F1602) at the same time
when you exchange P-Board.
The fuse is not bundled to P-Board for the repair.
1. Disconnect the couplers (P2, P5, P9, P10, P11, P12, P23,
P25, P51, P53, P55).
2. Remove the 19 screws and then remove the P-Board.
6.10. Removal of the SU-Board and
the SD-Board
1. Remove the flexible cables from the couplers (SU1, SU2,
SU3, SU4, SU5, SD1, SD2, SD3, SD4, SD5).
2. Disconnect the couplers (SU45, SD46).
3. Remove the each 4 screws.
4. Slide the SU-Board and the SD-Board to the left, remove
the SU-Board and the SD-Board from the couplers (SC41,
SC42, SC43, SC44).
Note:
The handling of a connector connecting with SC45-
SU45 and SC46-SD46 must note enough.
(DISCONNECTION and TRANSFORMATION,etc.)
11
TH-65PF9UK

6.11. Removal of the SC-Board
1. Disconnect the couplers (SU45, SD46).
2. Remove the each 4 screws.
3. Slide the SU-Board and the SD-Board to the left, remove
the SU-Board and the SD-Board from the couplers (SC41,
SC42, SC43, SC44).
4. Disconnect the 2 fan relay couplers.
5. Remove the each 4 screws and then remove the Fan Block.
6. Disconnect the couplers (SC2, SC20, SC23).
7. Remove the 10 screws of the SC-Board and slide the SC-
Board in the direction of the arrow (A) and then remove the
SC-Board.
Note:
Remove the SC-Board not to damage the flexible cables
of the SU-Board and the SD-Board, parts on the SC-
Board.
6.12. Removal of the SS2-Board and
the SS3-Board
1. Disconnect the coupler (SS23).
2. Remove the flexible cables from the couplers (SS51,
SS52).
3. Disconnect the coupler (SS27).
4. Remove the flexible cables from the couplers (SS57,
SS58).
5. Remove the each 3 screws and then remove the SS2-
Board and the SS3-Board.
6.13. Removal of the SS-Board
1. Disconnect the 2 fan relay couplers.
2. Remove the 4 screws and then remove the Fan Block.
3. Disconnect the couplers (SS11, SS12, SS23, SS27, SS34,
SS35, SS42, SS44).
4. Remove the flexible cables from the couplers (SS53, SS54,
SS55, SS56).
12
TH-65PF9UK

5. Remove the 11 screws of the SS-Board and slide the SS-
Board in the direction of the arrow (B) and then remove the
SS-Board.
Note:
Remove the SS-Board not to damage the flexible cables
of the Plasma Panel and parts on the SS-Board.
6.14. Removal of the H3-Board
(L), (R)
1. Remove the each 2 screws and then remove the Speaker
Terminal Blocks (L), (R).
2. Disconnect the coupler (H37).
3. Remove the 3 screws (H) and then remove the H3-Board.
13
TH-65PF9UK

6.15. Removal of the C1, C2, C3, C4,
C5 and the C6-Board
1. Disconnect the 3 fan relay couplers.
2. Remove the each 4 screws ( ) and then remove the Fan
Blocks (A), (B).
3. Remove the each 2 screws ( ) and then remove the
Speaker Terminal Blocks (L), (R).
4. Remove the each 2 screws ( ) and then remove the
Reinforcement Angles (L), (R).
5. Remove the each 4 screws ( ) and then remove the
Connection Plates (A), (B), (D), (E), (F), (H).
6. Remove the each 7 screws ( ) and then remove the
Connection Plates (C), (G).
6.15.1. Removal of the C1-Board
1. Remove the flexible cables from the couplers (C10, C11).
2. Remove the 10 screws ( ) and then remove the flexible
cables from the couplers (CA1, CA2, CA3, CA4, CA5).
3. Remove the 6 screws ( ) and then remove the C1-Board.
14
TH-65PF9UK

6.15.2. Removal of the C2-Board
1. Remove the flexible cables from the couplers (C21, C22,
C24, C25).
2. Remove the 10 screws ( ) and then remove the flexible
cables from the couplers (CA6, CA7, CA8, CA9, CA10).
3. Remove the 6 screws ( ) and then remove the C2-Board.
6.15.3. Removal of the C3-Board
1. Remove the flexible cables from the coupler (C31).
2. Disconnect the couplers (C35).
3. Remove the 10 screws ( ) and then remove the flexible
cables from the couplers (CA11, CA12, CA13, CA14,
CA15).
4. Remove the 6 screws ( ) and then remove the C3-Board.
6.15.4. Removal of the C4-Board
1. Remove the flexible cable from the coupler (C41).
2. Disconnect the couplers (C42, C44).
3. Remove the 10 screws ( ) and then remove the flexible
cables from the couplers (CB11, CB12, CB13, CB14,
CB15).
4. Remove the 5 screws ( ) and then remove the C4-Board.
6.15.5. Removal of the C5-Board
1. Remove the flexible cables from the couplers (C51, C52,
C54, C55).
2. Remove the 10 screws ( ) and then remove the flexible
cables from the couplers (CB6, CB7, CB8, CB9, CB10).
3. Remove the 6 screws ( ) and then remove the C5-Board.
15
TH-65PF9UK

6.15.6. Removal of the C6-Board
1. Remove the flexible cable from the coupler (C60, C61).
2. Remove the 10 screws ( ) and then remove the flexible
cables from the couplers (CB1, CB2, CB3, CB4, CB5).
3. Remove the 5 screws ( ) and then remove the C6-Board.
6.16. Removal of the Fan
1. Disconnect the 7 fan relay couplers.
2. Remove the each 4 screws and then remove the Fan
Blocks (A), (B), (C), (D).
6.16.1. Removal of the Fan (A)
1. Remove the 4 screws and then remove the Fan (A).
6.16.2. Removal of the Fan (B) and the
Fan (C)
1. Remove the 4 screws ( ) and then remove the Fan (B).
2. Remove the 4 screws ( ) and then remove the Fan (C).
6.16.3. Removal of the Fan (D), (E)
1. Remove the each 4 screws and then remove the Fans (D),
(E).
16
TH-65PF9UK

6.16.4. Removal of the Fan (F), (G)
1. Remove the each 4 screws and then remove the Fans (F),
(G).
6.16.5. Removal of the Fan Sponge
Note:
The Fan Sponges are unsuitable to reuse.
Please use a new one at the time of Fan exchange.
6.17. Removal of the S1-Board, the
V1-Board, the Power Button
and the Hinge Button
1. Disconnect the couplers (DS2, SS34).
2. Remove the 18 screws.
3. Lift up the bottom of the Plasma Panel in the direction of the
arrow1 and pull the Plasma Panel in the direction of the
arrow2 and then remove the Plasma Panel.
4. Remove the 2 screws (I) and then remove the S1-Board
Block.
5. Remove the Power Button from the S1-Board Block.
6. Remove the 1 screw (J) and then remove the S1-Board.
7. Disconnect the coupler (S34) and then remove the S1-
Board.
8. Remove the 2 screws (K) and then remove the V1-Board.
9. Disconnect the coupler (V34) and then remove the V1-
Board.
17
TH-65PF9UK

10. Remove the Hinge Button Block from the Escutcheon.
6.18. Removal of the Escutcheon
and the Front Glass
1. Disconnect the couplers (DS2, SS34).
2. Remove the 18 screws.
3. Lift up the bottom of the Plasma Panel in the direction of the
arrow1 and pull the Plasma Panel in the direction of the
arrow2 and then remove the Plasma Panel.
4. Remove the each 23 screws and remove the fixed Angles
(A), (B), (C), (D).
5. Remove the Front Glass.
18
TH-65PF9UK

Note: when Front Glass is exchanged
· Along each fixed Angles of an top and bottom, right
and left order and the sponge for the Front Glass is
pasted to the Front Glass.
Note
· The sponges are parts which cannot be recycled.
Please use the new article when you exchange the
Front Glass.
6. Remove the 2 screws (L) and then remove the S1-Board
Block.
7. Remove the 2 screws (M) and then remove the V1-Board
and the Hinge Button Block.
8. Remove the Escutcheon.
6.19. Removal of the Plasma Panel
· The C1,C2,C3,C4,C5,C6 Boards are connected with the
plasma panel for the repair.
1. Disconnect the couplers (PB30, PB31, PB32, PB33, PB34,
PB35, PB36, PB38).
2. Remove the 2 screws and then remove the PB-Board.
3. Remove the each 4 screws and then remove the Fan
Blocks (A), (B), (C), (D).
4. Remove the each 2 screws and then remove the
Reinforcement Angles (L), (R).
5. Remove the flexible cables from the couplers (DN1, DN6).
6. Remove the couplers (DN2, DN3, DN51).
19
TH-65PF9UK

7. Remove the 4 screws and then remove the DN-Board
Block.
8. Disconnect the couplers (DS2, DS4, DS7, DS8, DS10,
DS15, DS30).
9. Remove the 5 screws and then remove the Slot Block.
10. Disconnect the couplers (D20, D25).
11. Remove the flexible cables from the couplers (D31, D32,
D33, D34, D35, D36).
12. Remove the 4 screws and then remove the D-Board.
13. Disconnect the couplers (P2, P9, P11, P12, P23, P51, P53,
P55).
14. Remove the 19 screws and then remove the P-Board.
15. Remove the each 2 screws and then remove the Speaker
Terminal Blocks (L), (R).
16. Remove the each 4 screws ( ) and then remove the
Connection Plate (A), (B), (D), (E), (F), (H).
17. Remove the each 7 screws ( ) and then remove the
Connection Plate (C), (G).
20
TH-65PF9UK