Panasonic PT-51G46C User manual

H
naSOnuC
Color Projection5ysiiem
Operating Instructions
PT-51 G46
PT-51 G46C PT-61G46
Read these instructions completely before operating.
Contents subject to change without notice or obligation.
NO'I'E: The Cabinet Glass Doors Installation Instructions
are located in the back of this Manual.
Copyright 1997 by Matsushita Electric Corporation
of America. All rights reserved. Unauthorized
copying and distribution is aviolation of law. Printed in U.S.A.
-I-QB2AA0109-1

Safety Instructions
WARNING
WARNING: To reduce the risk of electric shock do not remove cover or back. No
user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with The exclarnationpointwithin
__. arrow-head within a triangle Aa triangle is intended to tell
is intended to tell the user ,__ the user that important
that parts inside the product operating and servicing
are a risk of electric shock to instructions are ir_the papers
persons, wi'Ih the appliance.
Note to CATV System Installer: This reminder is provided to call the CATV system installer's attention to Article
820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as I_ractical.
Safety Instructions for Television Receivers
1. Read and apply the operating instructions provided with your television receiver.
2. Read all of the instructions given here and retain them for later use.
3. Unplug this television receiver from the wall outlet before cleaning. Do not use liquid or ,aerosol cleaner,,;. Use a damp
cloth for cleaning.
4. Do not use attachments not recommended by the television receiver manufacturer as they may cause Iqazards.
5. Do not use this television receiver near water. For example: Avoid placing it near a bathtul:, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool, etc.
6. Do not place this television receiver on an unstable cart, stand or table. The television receiver may fall, causing serious
injury to a child or adult, and serious damage to the appliance. Use only with a cart or stand recommended by the
manufacturer, or sold with the television receiver. Wall or shelf mounting should follow the manufacturer's instructions,
and shoulc_iuse a mounting kit approved by the manufacturer.
6A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
7. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure
reliable operation of the television receiver and to protect it from overheating. These openings must not be blocked or
covered. The openings should never be blocked by placing the television receiver on a bed, sofa, rug or other similar
surface. This television receiver should never be placed near or over a radiator or heat register. This television receiver
should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.
8. Operate only from the type of power source indicated on the marking label. If you are not sure of the type of power
supplied to your home consult your television dealer or local power company. For television receivers designed to
operate from battery power, refer to the operating instructions.
9. This television receiver is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If yo_Jare unable to insert the plug
fully into the outlet, try reversing the plug. If _
the plug should still fail to fit, contact your '---"_-'-[_'-_
electrician to replace yourobsolete outlet. Do EXAMPLE OF ANTENNA GROUNDING AS t'_ ANTENNALEAD-IN
not defeat the safety purpose of the polarized PER(NEC)NATIONALELECTRICALCODE I'_ WIRE
plug.
10. Do not allow anything to rest on the power _ /
cord. Do not locate this television receiver _ GROUND/// C]_[_ "_
where the cord will be abused by persons cLAup _]
walking on it. ANTENNA
11. Follow all warnings and instructions marked /DISCHARGEUNIT
on the television receiver. CZ¢'1 (NEC SECTION 810-20)
12. Do not ow_=rloadwall outlets and extension
!
cords as this can result in fire or electric
shock.
13. Never push objects of any kind into this _ROUNr)INGCONDUCTORS
(NEC SECTION 810-21)
television receiver through cabinet slots as
they may touch dangerous voltage points or GROUNDCLAMPS
short out parts that could result in a fire or POWERSERVlCEGROUNDING
ELECTRODE SYSTFM
electric shock. Never spill liquid of any kind on {NECART250.PAR[H)
the televisi_on receiver.
-2-

14. Ifan outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide
some protec'tion against voltage surges and built up static charges. In the U.S. Section ,310 of the National Electrical
Code and in Canada Part 1 of the Canadian Electrical Code provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding electrodes, ancl requirements far the grounding electrode.
See Figure.
15. For added protection for this television receiver during a lightning storm, or when it is left urattended and unused for long
periods of tirne, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due to
lightning and power-line surges.
16. An outside antenna system should not be located in the vicinity of overhead power lines or 3ther electric light or power
circuits, or where it can fall !nto such power lines or circuits. When installing an outside antenna system extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. Unplug this television receiver from the wall outlet, and refer servicing to qualified service personnel unde r the following
conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the television receiver.
c. If the television receiver has been exposed to rain or water.
d. If the television receiver does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions as improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the television receiver to normal operation.
e. If the television receiver has been dropped or the cabinet has been damaged.
f. When the television receiver exhibits a distinct change in performance - this indicates a need for service.
18. Do not attempt to service this television receiver yourself as opening or removing covers m_Lyexpose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
19. When replacement parts are required, be sure the service technician has used replacement parts specified by the
manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Upon completion of any service or repairs to this television receiver, ask the service technician to perform routine safety
checks to determine that the television is in safe operating condition.
21. WARNING:: To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
22. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH ARECEPTACLE OR
OTHER C)UTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSLJRE.
Note: This equipment is designed to operate in the U.S.A., Canada and other countries where tqe broadcastiqg system and
AC house current is exactly the same as in the U.S.A. and Canada.
Important Information Regarding Use of Video Games, Computers, DSS or Other Fixed Image Displays.
The extended Jse of fixed image program material can cause a permanent "shadow im_Lge"on the picture tube. This
bac'kground image is viewable on normal programs in the form of a stationary fixed image. ]his type of irreversible picture
tube deterioration can be limited by observing the following steps:
A. Reduce the brightness/contrast setting to a minimum viewing level.
B. Do not display the fixed image for extended periods of time.
C. Turn the power off when not in actual use.
Note: Any marking or retained image on the picture tube resulting from fixed image use is not considerecl an operating
defect and as such is not covered by Warranty. This product is not designed to display fixed image patterns for
extended periods of time.
Specifications
Power Source:
Channel Capability:
Video Input Jacks (3):
Video Input Jacks (2):
A_ldio Input Jacks (3):
Audio Input Jacks (2):
To Audio AMP Jacks:
S-VHS Input Jack (1):
Stereo Sound
Closed Caption Display
Picture In Picture:
120V, 60Hz, AC
181 channels (See chart)
VHF 2-13, UHF 14-69, Cable 125 channels
lV p-p, 75 ohm, phono jack type (PT-61G46)
1V p-p, 75 ohm, phono jack type (PT-51G46)
500mV rms 47KD (PT-61G46)
500mV rms 47K£2 (PT-51G46)
0-2.0V rms 4.7K_
S-Video (Y-C) Connector
1 Tuner
Channel Capability Chart
CHANNELS
BAND
UHF
CABLE (Mid-Band)
CABLE (Super Band'
CABLE (Hyper Band:
CABLE (Ultra Band)
12
56
15
14
28
56
TOTAL. CHANNELS 181
Specifications are subject to change without notice or obligation.
3

Introduction
Congratulations on Your New Purchase
'Your new video component features an all solid state chassis which is designed to give you many years of enjoyment. It
was thoroughly tested and adjusted at the factory for best performance.
Inorder for you to take full advantage of your new video component, please read and follow the installation and operating
instructions supplied with this product.
Customer's Record
]-he model and serial number of this product may be found on its back cover. You should note the model and serial
number in the space provided and retain this book as a permanent record of your purchase: to aid in identification in the
event of theft or loss.
Ivlodel Number: Serial Number:
Care and Cleaning
Plastic Cabinets
'Wipe the cabinet with a soft cloth dampened with water or a mild detergent solution and wipe dry with a soft clean cloth.
.&void excessive moisture. Do not use benzene, thinners or other petroleum based cleaners.
Wood Cabinets
When dusting or polishing the cabinet, use a clean soft cloth and stroke straight with the grain. An occasional coat of
furniture polish will help preserve the finish. Do not use benzene, thinners or other petroleum based cleaners. Do not
place objects made of plastic or rubber directly on topof the cabinet. A chemical reaction coulcl result causing permanent
marring of the finish.
Remote Control Transmitter
Do not use benzene, thinners or other petroleum based cleaners to clean the Remote Control Transmitter. To clean,
wipe with a soft cloth slightly moistened with a mild detergent and then wipe dry with a soft clean cloth.
Screen Caution
Your Projection screen may be marred by accidental contacts or improper (:leaning.
Avoid BUMPING or SCRAPING the screen BY ANY OBJECTS.
Screen Cleaning
The projection screen has a orotective shield which isfully washable by using the following precautions. Use a mild soap
solution or window cleaner and a clean cloth. Do not use laundry detergent, automatic: dishwasher soap, abrasive
cleaners, products containing alcohol, ammonia or petroleum distillates. Avoid excessiw) moisture and wipe dry.
Power Loss
Prolonged power interruption causes the following features to reset to their factory preset state.
FEATURE FACTORY PRESET STATE
POWER OFF
VOLUMIE APPROX.-I/3
CHANNEL CH 03
PROGRAM MEMORY UNPROGRAMMED
VIDEO MENUS NORMALIZED
AUDIO MENUS NORMALIZED
STEREO/SAP/MONO STEREO
CLOCK NOT SET
FEATURE F.'ACTORY PRESET STATE
SLEEP TIMER NO/OFF
TIMER NO/OFF
ANTENNA MODE CABLE
TV/V IDEO TV
NOISE REDUCTION OFF
PIP FEATURES OFF
AUTO COLOR ON
MENU LANGUAGE ENGLISH

Table of Contents
Safety Instructions ............................. 2
Specifications ................................. 3
Introduction ................................... 4
Care and Cleaning ............................. 4
Power Loss .................................... 4
Installation .................................... 6
Receiver Location .............................. 6
Optional External Equipment Connections ........ 6
Condensation ................................. 6
AC Power Supply Cord ......................... 6
Remote Control Battery Installation .............. 6
Antenna/Cable Connections ..................... 7
Other Video Equipment ......................... 7
Optional Equipment Connection and Operation .. 8
Stereo Connection (to Audio AMP) .............. 8
Video/Audio Connection ........................ 8
S-Video Connection ............................ 9
PIP External Video and Antenna Connections ... 9
Location of Controls (Receiver) ................ 10
/.ocation of Controls (Remote) ................. 11
Basic Remete Control Functions ............... 11
Remote Control Quick Reference Functional
Key Chart ................................. 12
Special Functions ............................. 14
Recall Button ................................. 14
R-Tune (Rapid Tune) Button ................... 14
Multi Button .................................. 14
PIP (Picture in Picture) Button .................. 15
Swap Buttcn .................................. 15
Size Buttor .................................. 15
Freeze Button ................................ 15
Move Button ................................. 15
Main Menu (Trilingual Animated Icons) ......... 16
Menu Language Selection ................... 16
Picture Adj_Jstments ............................ 16
Picture Norm ............................... 16
Color, Tint, Brightness, Picture, and
Sharpness Adjustments ..................... 16
Color Temp ................................ 17
Auto Color ................................. 17
Video NR .................................. 17
Audio Adjustment ............................. 18
Audio Norm ................................ 18
Bass, Trehle, and Balance ................... 18
Mode (Stereo/SAP/Mono) ................... 18
Speaker ................................... 19
Surround .................................. 19
AI Sound .................................. 19
Input Select .................................. 20
Main (Picture) Input Selection ................. 20
PIP (Picture in Picture) Input Selection ........ 20
Timer Features ................................ 20
Sleep Timer ................................ 20
Dual Program Timer ......................... 21
Lockout Features ............................ 22
Lockout Mode .............................. 22
Unlock ..................................... 22
Favorite Channel Features ..................... 23
Channel Scan ............................... 23
Favorite Channel Select ..................... 23
Channel Caption Features ..................... 24
Preset Caption ............................. 24
Manual Caption ............................ 24
Set-Up Features .............................. 26
Clock (Auto) ............................... 26
Clock (Manual) ............................. 27
Set Day ................................... 27
Convergence Adj............................ 28
Mode (TV or Cable) ......................... 29
Auto Program .............................. 29
Manual Program ............................ 29
On Mute .............................. 30
r0-0--]Mode ................................ 30
Programming the Remote Control
Using Access Codes ....................... 31
Infrared Remote Codes for Specific Components 31
VCR Infrared Codes Inde:K ..................... 32
Cable Converter Box and CD Players
Infrared Codes Index ...................... 33
Cassette Players, AV Receivers, and Amplifiers
Infrared Codes Index ...................... 34
Laser Disc, DSS, and DVD
Infrared Codes Index ...................... 35
Cabinet Door Installation PT-51G46 ............ 36
Cabinet Door Installation PT-61G46 ............ 38
Troubleshooting Chart ........................ 40

Installation
P,eceiver Location
This unit can be used as an entertainment center. Consult your dealer for available options. Locate for comfortable
viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the screen.
Use of some types of fluorescent lighting can reduce remote control transmitter range.
AJequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or
moisture.
To insure optimum color purity do not position magnetic equipment (motors, fans, external speakers, etc.) nearby.
C)ptional External Equipment Connections
The Video/Audio connections between components should be made with shielded video _ncJaudio cables. For best
performance, video cables should utilize 75 - ohm coaxial shielded wire. Cables are available from your dealer or
electronic sup,ply house.
Before you purchase any cables, be sure you know what type of input and output connector_; your various components
rE'quire. Also determine the length of cable you'll need.
Condensation
When the set is moved into a warm room from a cold area, the picture may become out of focus because of
condensation on the lens surface due to the temperature change. Picture will be(;ome clear when the set
reaches the same temperature of the surrounding area.
AC Power Supply Cord
CAUTION: To prevent electric shock, match wide blade of plug towide slot of AC outlet and
fully nsert. DO NOT USE this (polarized) plug with a receptacle or other outlet unless the
lblade can be fully inserted to prevent blade exposure.
Remote Control Battery Installation
Batteries: Use two "AA" batteries.
1. Install the batteries as shown in the battery compartment.
(Polarity +) or (-) must be correct.)
Helpful Hints:
For frequent Remote Control users, replace old batteries with
Alkaline batteries for longer life.
CAUTION: Incorrect installation can cause battery leakage and corrosion
that will damage the Remote Control Transmitter.
Observe the Following Precautions:
1. Batteries should be replaced as a pair. Always use new batteries.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (Example: "Zinc Carbon" with "Alkaline").
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used
batteries.
5. Battery replacement is necessary when Remote Control reacts sporadically
or stops operating the Receiver.
Helpful Hints:
Whenever you remove the batteries to replace
them, you may need to reset the Remote Control
Infrared Codes. We recommend that you initially
record the codes in the Infrared Remote Codes for
Specific Components section, prior to setting up the
remote.
Polarb:ed Plug
Pres.,; Down Here
!!/
::: _==== ..
::" T7 ..
::: --
and Slide Cover
Back
-6-

Installation (cont.)
Antenna/Cable Connections
Antenna Connection - For proper reception of VHF/UHF channels, an external
antenna is required. For be.(;t reception an outdoor antenna is recommended.
Antenna Mode must be set to TV. (Refer to Antenna Mode section.)
75 Ohm
VHF/UHF
on Back of Set
Incoming Cable from Home Antenna
or
VHF/UHF
on Back of Set
Incloc r Outdoor
Typical VHF/UHF Antenna
300 Ohm
300 to 75 ohm Matching
Transformer (Not Included)
Cable Connection- For reception of cable channels, connect the cable supplied byyour local cable company. Antenna
Mode must be set to CABLE'. (Refer to Antenna Mode section.)
Incoming Cable from Cable Company
75 Ohm
VHF/UHF
on Back of Set
Note: Certain cable system.'_offset some channels to reduce interference or have Premium (scrambled) channels. A
cable converter box is required for proper reception. Check with your local Cable company for compatibility
requirements.
Other Video Equipment
VCRs, Video Disc Players, Computers, TV games, and DSS equipment carl also be connected to the antenna input
connection.

Optional Equipment Connection and Operation
"1"oAudio AMP Connection (Stereo) TERMINALS 'DN BACK OF RI--CEIVER
To Auxiliary Input
Connect To Audio AMP to an external audio
amp auxiliary input for monitoring sound through
e.stereo system.
Note: "TO AUDIO AMP" terminals cannot be used for external speakers.
Adjustment - When an audio amp is connected to "TO AUDIO AMP"
terminals:
1. Select SPEAKER "ON" Mode. (Refer to the Audio Menu Speaker
section.)
2. Set volume of audio amp to near minimum.
:3. Adjust volume of TV to desired listening level.
4. Adjust volume of audio amp to match the level of PTV.
5. Select SPEAKER "OFF&VAO" (Variable Audio Output) Mode. (Refer to
the Audio Menu Speaker section.)
6. Audio bass, treble, balance, volume, and mute can now be controlled by
the TV Remote Control. When "OFF&FAD" (Fix Audio Output) mode is
selected in the Audio Menu, the external amplifier speakers are
controlled by the Audio Amplifier.
Video/Audio Connection
Operation
IIF--- S-v,DEO
VIDEO OUT
I AUDIO OUT
I
I, lrERMINALS ON
BACK OF VCR
1. Connect optional equipment as shown to INPUT 1,2, or ,'3(input 3 is
located on front of Receiver).. PT-51G46 rncdels have two (2) Video
Inputs.
2. Select the desired Video mode by pressing the TV/VIDEO button (or
refer to the Input Select Menu).
Note: You must select the same VIDEO rv'oclethat the equipment is
connected to.
3. Operate optional equipment (VCR-VDP) as instructed in Optional
Equipment manual.
-8-

Optional Equipment Connection and Operation (cont.)
S..Video Connection
VCR S-VIDEO (YC)
CONNECTOR OPTIONAL
T|'RMINALS ON
BACK OF VCR
[ ......
_b,'_ S-VIDEO; i
VIDEO OUT
•UD_OOU
R I
TERMINALS ON BACK OF RECEIVER
Operation
1. Connect S-Video (YC) connector to S-Video Terminal 1.
2. Make connections to Input 1 Audio Jacks (L and R).
3. Select Video 1 mode by pressing the TV/VIDEO button (or refer to
the Input Select Menu).
4. Operate optional equipment (VCR-VDP) as instructed in Optional
Equipment Manual.
Helpful Hints: I
The User must select the same VIgEO'_locle that the I
equipment is connected to. I
Connection of optional S-VIDEO jack automatically I
disconnects the normal Video Input 1 iack. J
Picture in Picture External Video and Antenna Connection
This Receiver' has the "PICTURE IN PICTURE" feature. For the proper operation of this featurE,a second video source is
required (such as a VCR). We recommend that you make your antenna and External Video connection as shown below
when a second video source is available.
TERMINALS ON BACK OF VCR
Incornir_g Cable
From Antenna or
Cable 1V System
To VCR
Sig "_alSplitter
(not Included)
TE-RMINALS ON BACK OF RECEIVER
IHeipful Hints: :
The PIP will operate using Audio/Video input terminals. Use the TV/VIDEO I
button (when the PIP frame is displayed) to select proper mode. ,I
The PIP feature will operate using S-Video input tE.rminal 1. J
9

Location of Controls (Receiver)
PT-51 G46 Models PT-61 C146Models;
\_ Front Control Panel
POWER •VOI..UMEII_ YCHANNFLA ACTION W/VIDEO
Located Behind Door
(PT-61G46 Models Only)
AUI)IO
VIDEO L R
®
Quick Reference Control Operation
(1_ Power Button - Press to turn ON or OFF.
(2_) Volume Buttons- Press to adjust Sound Level. Press to adjust Audio Menus, Video Menus, and select operating
features when menus are displayed.
(3_) Channel Buttons - Press to select programmed channels. Press to highlight desired features when menus are
displayed.
(4_) Action Button - Press to display Main Menu and access or exit On-S(-reen feature arid Adjustmenl Menus.
(5_) TV/Video Button- Press to select TV, or one of three Video Inputs for the Main Picture, or the PIP frame (when the
PIP frame is displayed). Note: PT-51G46 models have two (2) Video Inputs.
-10-

Location of Controls (Remote)
fBas Remot_ eCon_ _tro_ lFunc___tion_ s
The following isanovervewof theRemOteControl untfor televisionoperation. Ensurethe
TV mode is selected by initially pressing _ .
Multi Button
Programmable to operate up to six
Remote Control Function buttons
simultaneously.
Power Button
Press to turn ON or OFF.
Mode Selection Buttons
Select the operation mode for the
remote control.
Volume Buttons
Press to adjust TV sound level.
Use with Channel buttons
navigate in menus.
Action Button
Press te display Main Menu and
access or exit On Screen feature
and Adjustment Menus.
R-Tune (Rapid Tune) Button
Press to switch to the previous
channel.
PIP Move Button
Press to position PIP frame to any
corner of the Main Picture (when PIP
frame is displayed).
PIP Freeze Button
Press to stop action ;n the Main
Picture ,DrPIP frame (when the PIP
frame is displayed).
PIP Size Button
Press to select size of PIP frame
(when the PIP frame is displayed).
Keyboard "0 through 9" Buttons
Press desired charnel number 1:o
randomly access ary channel.
TV[Video Button
Press to select TV or one of three (3)
Video Inputs, for the Main Picture or the
PIP frame (when the PIP flame is
displayed). Note: PT-51G46 models
have two (2) Video Inputs.
Mute Button
Press to mute sound. A second press
resumes sound.
Channel Butto ns
Press to select channels. Use with
Volume buttons to navigate in menus.
Recall Button
Press to displa.y Time, status of Sleep
-I-imer, Channel, Video Mode, Channel
Caption (Station Identifier) and Audio
Mode.
PIP (Picture In Picture) Button
Press to display the PIP frame, press
again to remove PII_ frame.
PIP Swap Button
Press to interchange PIP frame with Main
Picture (when the, PIP frame is displayed).
VCF:IFunction Bultons
Programmable to oaerate many brands of
VC:R's.
VCR/DSS Channel Buttons
Select VCR or DSS Up/Down channels.
Home Theater Remote Control
TNQ2AE007-1
Note:
For more information on the Remote
Control, please refer to the Remote
Control Quick Reference Functional Key
Chart.
Helpful Hints:
If the selecled component does not
respond to the remote control, ensure
that the proper mode is selected,
First, press the Mode Selection
Button that corresponds to that
component. For example, after first
pressing th£ TV Mode Button, the
remote will remain inthe TV mode for
the following commands. Ifa different
mode button is pressed while
operating the television, the TV mode
button must be pressed again to
enable the -i-V mode condition.
-11 -

Remote Control
Quick Reference Functional Key Chart
C)
@
®
®
®
®
®
0
@
®
®
®
TV
VCR, VCR2
CABLE, DSS
RECEIVER/AMPLIFIER
CD PLAYER
LD PLAYER
ALL COMPONENTS
TV
ALL COMPONENTS
T% DSS, VCR, VCR2LDP
CABLE
RECEIVER/AMPLIFIER
TV
Selects Channel
Selects Channel
Selects Channel
Q Selects Tuner
(_) Selects CD Player
(_ Selects Tape Cassette Player
® VCRt
@ VCR 2
Selects Track Number
CABLE Cable Mode Selection for Remote Coqtrol
DSS (DIGITAL SATELLITE DSS Mode Selection for Remote Con
SYSTEM)
VCR, VCR 2VCR Mode Selection for Remote Con
RECEIVER/AMPLIFIER Receiver/Amplifier Mode Selection for Remote Control
COMPACT DISC CD Mode Selection for Remote Contr
CASSEFrE PLAYER, VCR AUX Mode Selection for Remote Con
2, DVD Enables User to Operate a Tape Cas.' Player,
Digital Video Disc or Second VCR
LASER DISC PLAYER LD Mode Selection for Remote Contn
TV
CABLE
DSS
LDP
CD
RECEIVER/AMPLIFIER
DVD
TV
CABLE
DSS
RECEIVEWAMPLIFIER
VCR, VCR2
LDP
Selects Track Number
Programmable Button That Can Oper_.te Up To Six (6)
Remote Functions At Once
Selects the TV Input lVlode
Turns On and Off Selected Compone_
Mutes TV Audio
Mutes Audio
Mutes Audio
TV Mode Selection for Remote Contr(
Channel Up/Down, Menu Navigation
Channel Up/Down
DSS Guides and Menu Navigation
Skip
FF, REW
Preset or Tuning Frequency
Skip FWD/Skip REW
Volume Up/Down, Menu Navigation
Volume Up/Down
DSS Guides and Menu Navigation
Volume Up/Down
TV Volume Up/Down
TV Volume Up/Down
-12-

Remote Control
Quick Reference Functional Key Chart {cont.)
REW
MOVE
PLAY
SIZE
FF
PIP
REC
STOP
PAUSE
SNAP
TV/VCR
FREEZE
0
VCR/DSS CH
LDP
TV
CABLE
VCR, VCR 2
DSS
RECEIVER/AMPLIFIER
CD
TAPE CASSETTE PLAYER
TV
DSS
TV
DSS
VCR, VCR 2
LDP
TV
DSS
VCR, VCR 2
LDP
TAPE
CD
DVD
TV
DSS
VCR, VCR 2
LDP
TAPE
CD
DVD
TV
DSS
VCR, VCR 2
LDP
TAPE
CD
DVD
DSS
VCR, VCR 2
TAPE
CABLE
DVD
VCR, VCR 2
LDP
TAPE
CD
CABLE
DVD
TV
VCR, VCR 2
LDP
TAPE
CD
CABLE
TV
VCR, VCR 2
DSS
CABLE
VCR, VCR 2
DSS
Side A/B
Switches Between Two (2) Channels
Switches Between Two (2) Channels
Switches Between Two (2) Channels
Switches Between Two (2) Channels
Switches between AM and FM
Selects Next Disc:
Selects Tape Cassette Player A or B
Activates TV Menus
Acts as Menu Button for DSS
Displays Channel, Sleep Time,Chanqel Caption, Time,
and Audio ModE;
Displays Current DSS Settings
Displays Current VCR Settings
Displays Current LDP Settings
PIP Move
DSS Guide
Rewind
Rewind
Rewind
Selects Previous Track
Rewind
PIP Size
Enter/Select
Play
Play
Play (in Normal r)irection)
Play
Play
PIP On/Off
Exit/Clear
Fast Forward
Fast Forward
Fast Forward
Selects Next Track
Fast Forward
One Touch Record in DSS Mode
Record
Record
VCR Record
Stop
Stop
Stop
Stop
Stop
VCR Stop
Pause
PIP Swap
Pause
Pause
Pause
Pause
VCR Pause
PIP Freeze
Selects TV/VCR Mode
Selects TV/DSS Mode
Selects TV/VCR Mode
Channel Up/Down
Channel Up/Down
-13-

Special Functions
Recall Button
Press the RECALL button to review:
,:_1_)Audio Mode status
_) Channel Caption (Station Identifier)
c_) CH number or Video Input selected
_} Sleep Timer status
$5_5)Clock time
KXYZ CH 3
(_) 29 1:00
G @
R-Tune Button
Pressing the R-TUNE (RAPID TUNE) button will switch
between the last two channels selected on the numeric
keypad.
Note: When rapidly scanning channels with the
CHANNEL UP/DOWN button, pressing the
R-TUNE button will switch between the last
channel scanned, and initial channel at the start
of scanning.
CHANNEL NOW CHANNEL TUNED
BEING VIEWED IMMEDIATELY BEFORE
Press Button
Press Buttcn Again
l
Helpful Hints:
Press the ]-V Mode Selection button to operate TV
Remote functions, if necessary.
Multi Button
The MULTI button can be pro ;Irammed to operate up
to six (6) Remote function bu;ttons at the same time.
For Example: TV Power/On, VCR Power/On, and
Cable box Power/On (selected brands) can I:,eoperated
at the same time with one press of the MULTI button.
(The VCR Mode button should be programmed
before starting procedure').
Procedure
1. Program the Remote for th_ selected device Infrared
access code. Confirm that the Remote Control is
compatible with the device.
2. Face the Flemote Control transmitter away from al!
equipment remote sensor,&
3. Press and hold the Remote POWER button, then
press and hold the ACTION button down at the
same time for three seconds. (All previous
are rased
PRESS AT THE SAME TIME FO
THREE SECONDS
4. After three seconds, "elease the POWER and
ACTION buttons.
5. Press the MULTI button. (Waiting more than 30
seconds without pressing another button will exit the
programming mode.)
6. Press a maximum of six (6) function buttons on the
Remote Control.
Each button you press is equal to one function. If six
(6) Remote button functions are entered, all will
register in the MULTI button memory in the
sequence entered. When :inished, press the MULTI
button to exit the programming mode.
The following is an example flow chart of Remote
functions that can be programmed into the MULTI
button.
PRESS AT 3"HE SAME TIME FOR
THREE SECONDS
PRESS PRESS
PRESS PRESS
PRESS TO EXIT
PROGRAMMING MODE
You can now turn the -fV and VCR ON/OFF at the
same time, with one pres_ of the MULTI button.
To delete entered fum;tions - Press and hold the
Remote POWER button, then press and hold the
ACTION button down at the same time for three
seconds. You can now enter from one to six different
Remote functions.
Note: You can also program the MULTI button to
perform most individual Remote Control button
functions. Buttons which continuously perform a
function as long as pressed (Volume Up/Down,
Channel Up/Down, etc.) cannot be programmed;
only those buttons which perform a function
when initially pressecl (Power On/Off, Mute,
Direct Channel Entry, etc.) can be pJ'ogrammed.
-14-

Special Functions (cont.)
PIP (Picture in Picture) Button
This feature allows the viewer to monitor one channel
program while watching another. The monitored source
(PIP) must be.a different video source (such as a VCR)
when connected to the input jacks.
• S-Video connection will also operate the PIP feature
(refer to OPTIONAL S-VIDEO VHS CONNECTION
section).
• When the Main Picture is in Video mode with no
signal, the PIP will not operate properly.
PIP Operation
1. Turn VCR ON and select a desired channel.
2:. Press the TV Mode Selection button to operate TV
Remote lunctions, if necessary.
3. Press the PIP button (set must be ON). The PIP
frame will appear at the position it was last
displayed. The Main Picture Video Source and PIP
Video Source will display on screen momentarily.
Audio will be that of Main Picture.
PIP
Main
Picture
with
Audio
4.
CH 2"
PIP VIDEO 1
Main Picture
91_ Channel
Picture in
Picture
Video Source
Picture in
Picture
Frame
Press the PIP button again to cancel PICTURE IN
PICTURE feature (if desired).
Note:
PIP
For PIP Video source connection, refer to the
PiP Fxternal Video and Antenna Connections
section.
Swap Button
Press the SWAP button (when the PIP frame is
clisplayed) to interchange what is being viewed on the
lvlain Picture with that of the PIP frame.
SWAP
CH2t_
PIP VIDEO 1
VIDEO 1 I
PIP CH 2
Size Button
Press the SIZE button (when the PIP frame is displayed)
to choose either the large or small PIP frame.
ISIZE
!:71
/
Large PIP Frame Small PIP Frame
Freeze B utton
Press the FREEZE buttor, to stop action in the PIP
frame. FREEZE
Main
Picture
[_. __ FreezeFrame
Notes:
• Pressing the FREEZE button when the PIP frame is
not displayed, will stop action in the Main Picture and
display it within the PIP frame.
• Pressing the FREEZE button when PIP frame is
displayed, will stop action in the PIP frame. Press the
FREEZE button again to continue action.
• Press the PIP button to de ete PIP frame.
Move Button
The PIP frame may be located at any corne_rof the Main
Picture by pressing the PIP MOVE button (when the PIP
frame is displayed). MOVE
Note: Each time MOVE button is pressed (when the
PIP frame is displayed), the PIP frame will move
counterclockwise as illustrated.
[-1" I--I
[-1 -i--1
-15-
Note: Audio will be that of Main Picture.

Main Menu
(Trilingual Animated Icons)
m
F_us.
NOTE: Only the selected Icon will be animated.
Display and Exit Menus
CH BUTTONS
Highlight Desired
Feature when
Menu is Displayed
VOL BUTTONS
Selects or Adjusts
Features when
Menu is Displayed
Located On Remote Control
Menu Language Selection
The LANGUAGE MENU is factory set to ENGLISH.
Follow the instructions to change the Language Menu
to SPANISH, FRENCH, and back to ENGLISH.
1 Press
2 Press //_ or_ ?and _o_ or _ to highlight the
Language ENGLISH/ESF'AIXIOL/FRAN(_AIS Icon.
3. Press *__'_ to display the Language select Menu.
4. Press _ or_ _7to select ENGLISH, ESPANOL or
FRANQAIS for the Language Menu.
5. Press___ twice to exit menus.
-16-
Picture Adjustments
Picture Norm
Use to reset Color, Tint, Brightness, Picture, and Sharpness
adjustments back to a factory preset level.
1. Press _.
2. Press Z_ or_ ?and _ or _;:_to highlight the Picture
Icon.
3. Press _-]) to display the Picture Adjustrnent Menu.
ilii
iiiiiiiiiiiiiiliiiiiii!iiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiii_ii%iiiiii
4. Press Z_ or_ to highlight PICTURE NORM.
5. Press _ or _ to select "SET" to normalize Color,
Tint, Brightness, Picture, and Sharpness.
6. Press '_-3_} twice to exit menus.
Color, Tint, Brightness,
Sharpness Adjustrnents Picture, and
1. Press _-_).
2. Press Z_ or_ ?and _ or _ to highlight the Picture
Icon.
3. Press @) to display the Picture Adjustment Menu.
4. Press _, or_ to select the desired Picture
Adjustment (Color, Tint, Brightness, Picture, or
Sharpness).
5. Press _ or _ to adjust your selection. (The
Selected Picture Adjustment will be displayed.)
6. Repeat steps 4 and 5 for the remaining Picture
Adjustments.
7. Press _)_ twice to exit menus.

Picture Adjustments (Cont.)
Color Temp
To select from three (3) options for picture temperature.
1. Press _______.
2. Press Z_ or_ ?and _ or _}b to highlight the Picture
Icon.
3. Press _ to display the Picture Adjustment Menu.
4. Press z_ or_ ;2to highlight COLOR TEMP.
5. Press _ or _;) to select NORMAL, WARM, or COOL.
• NORMAL (no tint)
° WARM (reddish tint)
• COOl_ (bluish tint)
6. Press _ twice to exit menus.
Auto Color
To automatically optimize color adjustment to compensate
for signal variations.
1. Press G[;_.
2. Press S_ or_' and _ or _ to highlight the Picture
Icon.
pr__^ ('-,_
3. _ ___ to display the Picture Adjustment Menu.
Video NR (Noise Reduction)
To reduce video noise (snow in picture) due to weak signal.
1. Press @).
2. Press Z_ or_;_ and _ or _ to highlight the Picture
Icon.
3. Press _) to display the Picture Adjuslment Menu.
!ii_iiiiii_iiiii_ii_!!!!!i_iiii!_ii_i_ii_iii_iiii_ii_ii_!_iiiii_iiiiiii_iii!iiiii_iiii_ii_iii_i_iiiii_iiiiiii_iiiiiiii_i_i_iii!_ii_i_!_ii!!_i_!_!!_ii
4. Press _ or_7 to highlight VIDEO
Reduction).
5. Press _ or _ to select ON or OFR
6. Press_-___})twice to exit menus.
NR 'Noise
Helpful Hints:
COLOR -Adjust for desired color intensity.
TINT - Adjust for natural flesh tones.
BRIGHTNESS- Adjust so d_Lrkareas of picture slightly
become black for a crisp detail.
PICTURE - ,Adjust the white areas of the picture as
desired.
SHARPNESS - Adjust for best clarity of outline detail.
4. Press _, or_ ;2to highlight AUTO COLOR.
5. Press _ or _ to select ON or OFF.
6. Press(__._ twice to exit menus.
-17-

Audio Adjustments
Audio Norm
This feature is used to reset BASS, TREBLE, and
BALANCE back to a factory preset level. Note: Bass and
Treble is automatically set when AI Sound is ON.
1. Press _}_.
2. Press _ or_2 and < or _:_ to highlight the Audio
Icon.
3. Press _)_ to display the Audio Adjustment Menu.
4. Press_ or_ 7to highlight AUDIO NORM.
5. Press _ or _ to select SET to normalize Bass,
Treble, and Balance.
6. Press _ twice to exit menus.
Bass, Treble, and Balance
1. Press _°"_.
2. Press _ or_ _2and _ or _:_ to highlight the Audio
Icon.
3. Press _¢1_="_to display the Audio Adjustment Menu.
L
i_iili_iii !! i !_! !
4. Press /---_ or_ to highlight BASS, TREBLE, or
BALANCE.
5. Press _ or _ to adjust for desired audio response.
6. Press *___ twice to exit menus.
Helpful Hints:
BASS - To increase or decrease the Bass response.
TREBLE -- fb increase or decrease the Treble response.
BALANCE -- To emphasize the LEFT/RIGHT speaker
volume.
Mode (Stereo/SAP/Mono)
When Audio is broadcast in Stereo or SAP, an On-Screen
display will appear on initial 'Turn On" and "Channel
Change". The available choices will be indicated in red.
1. Press@).
2. Pressz_ or_ and < or _ to highlight the Audio
Icon.
3. Press @_ to display the Audio Adjustment Menu.
.
5.
,
Press _ or_ to highlight MODE.
Press _ or _ to selecl: STEREO, SAP (Second
Audio Programming), or MONO. The selected mode
will be highlighted.
Press _) twice to exit rrenus.
Helpful Hints:
STEREO --P,vo channel Audio reception.
SAP - Second Audio Programming (typically used for
bilingual audio).
MONO - Use,when stereo signal is weak.
-18-

Audio Adjustments (cont.)
Speaker
This feature is used to turn the internal speakers "ON" or
"OFF". It is used when the TV is connected to an External
Audio Amplifier. (Refer to "-Ib Audio Amp Connection"
s_=ctionfor further information.)
1. Press _(_.
2. Press 8, or_ ?and _ or _ to highlight the Audio
Icon.
3. Press {_ to display the Audio Adjustment Menu.
4. Press _ or_ 7 to highlight SPEAKER.
5. Press or _ to select ON, OFF&VAO or
OFF&FAO.
• ON --TV SPEAKERS operate normally.
• OFF&VAO (Variable Audio Output) - TV
SPEAKERS off, the sound output varies
according tothe TV w31ume.Use the TV remote to
control the volume, muting, bass, treble, and
balance of the External Amplifier System.
• OFF&FAO (Fixed Audio Output) - TV
SPEAKERS off, sound output is not adjustable.
The audio is controlled by the External Amplifier
System volume control.
6. Press ___ twice to exit menus.
Surround
Use the Sur_round Feature to enhance audio response
when listening to Stereo broadcasts.
1. Press@ .
_-!. Press _ or_' and _ or _ to highlight the Audio
Icon.
3. Press _ to display the Audio Adjustment Menu.
4. Press _ or_(_?to highlight SURROUND.
5. Press _ or _ to select .DN or OFF.
6. Press _-)} twice to exit menus.
AI Sound
This feature is used to enhance sound quality through
automatic adjustment of bass and treble during speech or
music segments of the audio 3roadcast.
1. Press _-)__}.
2. Press _ or_ ?and _z_ or _ to highlight the Audio
Icon.
3. Press __-} to display the Audio Adjustment Menu.
4.
5.
6.
iiiiiiii!iiiiiiiiii_iiiiiiiiiiiiiiiili_iiiiiii!iiiiiiiiZ_"_iliiii_iiiii_
iilii:i:i:!iiiiiii:i!ii_i_ii!_!:i:i!iii:i_il!_i_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiililiililililili!i_i_iiiiii%iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiilili!iiiiiii_i_iii:iiii3i
Press _ or_ to highlight AI SOUND.
Press _ or _ to select ON or OFF.
Press _ twice to ext menus.
i¸iiii'!¸ !
-19-

Input Select
Main (Picture) Input Selection
Selecting TV Mode Operation or one of three Video Inputs
for the Main Picture (used with optional accessory Video
equipment).
1. Press _)).
2. Press _4 or_7 and _ or _ to highlight the Input
Select Icon.
3. Press _]) to display the Input Select Menu.
ii!iiiiii!ii!iii!iiiiiii!!i!iiii! iii!iiii!ii!!!i
_[_ii_iiiii!iiiii!i!iiii!iiiiiiiiiiiiiii_iiii_iiiii!iiii_iiiiiiiiiiiiii!iii!ii!i_iiii_ii_iiiiii!i!iii!iii!i_
4. Press _ or _ to select TV, VIDEO 1, VIDEO 2, or
VIDEO 3 for Main Picture Input. NOTE: PT-51G46
models have two (2) Video Inputs.
5. Press __)_ twice to exit menus.
PIP Input Selection
Selecting TV Mode Operation or one of three Video Inputs
for the PIP (Picture in Picture) frame when the PIP frame is
displayed (used with optional accessory Video
ecluipment).
1. Press C]_) (PIP button) to display the PIP frame.
2. Press _.
3. Press _ or_ ?and _ or _ to highlight the Input
Select Icon.
4. Press _ to display the Input Select Menu.
I
Timer Features
Sleep Timer
To automatically turn TV OFF:in 30, 60, or 90 minutes as
desired.
Note: Display will flash 3, 2, and 1 to indicate the last
three remaining minutes prior to turn OFF.
1. Press I_--)].
2. Press Z_ or_ and _ or _ to highlight the Timer
Icon.
3. Press _) to display the Timer Control Menu.
iiiiii!iiiii!iiiiii!iiilliiiiiii!iiiiiii!iiii!ii_i
4. Press _ to select NO, 30, 60, or 90 (minutes) for
Sleep Timer to be activated.
5. Press__)_ twice to exit menus.
Note: To ,deactivate Sleep Timer, in step 4, set to
"NC)".
iii _ iiiiiiiiii iiiiiiiiiiiiiiiiiiiiii:iiiiiiiiiiiiiiiiii!iiiiiiiiiiiiiiiilili[iiiiiiii!i!iiiiiiiiiiiiiiiiii!iii!i!iiiiiiiiiiiiiiiiii_i!iiiii!iiiii_i!iliii_]::i!
iii ii iiii iiii!i!iiiiiiiiiii!iiiiiiiiiii!iiiiiiiiiiiiiiiiiiiiii!iii¸iiiiiii!iiii!!iiiiiiiii!iiiii iiiii!iiiii !ili!
5. Press Z_ or_7 (when the, PIP frame is displayed) to
highlight PIP.
6. Press the'_ or _ to select TV, VIDEO 1, VIDEO 2, or
VIDEO 3 for the PiP frame Input. NOTE: PT-51G46
models have two (2) Video Inputs.
7. Press ___o_twice to exit menus.
- 20 -