Panasonic PT-DZ10K System manual

3-Chip DLP™Projector
As of April 2013. Specifications and appearance are subject to change without notice.
SFD12M023
1/17
Product Number : PT-DZ10K
Product Name :
SPEC FILE

As of April 2013
SFD12M023
2/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Specifications
Main unit
Power supply
Power consumption
DLP™ chip Panel size
Display method
Pixels
Lens
Lamp
Screen size
Brightness*2
Center-to-corner uniformity*2
Contrast*2
Resolution
Scanning frequency SDI
HDMI/DVI-D/RGB
YPBPR(YCBCR)
120 V AC, 9 A, 50/60 Hz
220–240 V AC, 4.7 A, 50/60 Hz
925 W (1,010 VA) (0.2 W with standby mode set to eco.*16 W with
standby mode set to normal. Both with fan stopped.)
900 W (980 VA) (0.3 W with standby mode set to eco.*19 W with standby
mode set to normal. Both with fan stopped.)
24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)
DLP™ chip × 3 (R, G, B), DLP™ projection system
2,304,000 (1,920 × 1,200) × 3, total of 6,912,000 pixels
Optional powered zoom/focus lenses
355 W UHM lamps (× 2) (dual lamp, normal mode)
1.78–25.4 m (70– 1,000 inches) (1.78–15.24 m (70–600 inches) with the
ET-D75LE8), 16:10 aspect ratio
10,600 lumens (dual lamp, normal mode)
90%
10,000:1 (full on/full off, in dynamic iris 3 mode)
1,920 × 1,200 pixels
3G-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i,
1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p
3G-SDI signal (YPBPR4:2:2 10-bit):
SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p
HD-SDI signal (YPBPR4:2:2 10-bit):
SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i,
1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,
1125(1080)/24sF, 1125(1080)/30p
SD-SDI signal (YCBCR4:2:2 10-bit):
SMPTE ST 259 compliant: 525i(480i), 625i(576i)
Horizontal: 15 kHz–100 kHz, vertical: 24 Hz – 120 Hz,
dot clock: 25 –162 MHz or lower (HDMI/DVI: 25 MHz – 162 MHz)
525i (480i): fH15.75 kHz; fV60 Hz,
625i (576i): fH15.63 kHz; fV50 Hz,
525p (480p): fH31.50 kHz; fV60 Hz,
625p (576p): fH31.25 kHz; fV50 Hz,
750 (720)/60p: fH45.00 kHz; fV60 Hz,
750 (720)/50p: fH37.50 kHz; fV50 Hz,
1125 (1035)/60i: fH33.75 kHz; fV60 Hz,
1125 (1080)/60i: fH33.75 kHz; fV60 Hz,
1125 (1080)/50i: fH28.13 kHz; fV50 Hz,
1125 (1080)/25p: fH28.13 kHz; fV25 Hz,
1125 (1080)/24p: fH27.00 kHz; fV24 Hz,
1125 (1080)/24sF: fH27.00 kHz; fV48 Hz,
1125 (1080)/30p: fH33.75 kHz; fV30 Hz,
1125 (1080)/60p: fH67.50 kHz; fV60 Hz,
1125 (1080)/50p: fH56.25 kHz; fV50 Hz
120 V AC, 50/60 Hz
220–240 V AC, 50/60 Hz
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Video/S-Video
Optical axis shift Vertical
Horizontal
±55% (±44% with the ET-D75LE6) from center of screen, powered
±20% (±15% with the ET-D75LE6) from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the
ET-D75LE50.

As of April 2013
SFD12M023
3/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Keystone correction range
Installation
Terminals SDI IN
HDMI IN
DVI-D IN
RGB 1 IN
R, G, B
Y, PB, PR(Y, CB, CR)
S-Video signal
RGB 2 IN
R, G, B
Y, PB, PR(Y, CB, CR)
VIDEO IN
Vertical ±40°, horizontal ±15°
(vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50,
vertical ±28° and horizontal ±15° with the ET-D75LE6)
When using only the KEYSTONE correction of the Geometric Adjustment
function: Vertical ±40°, horizontal ±15°
Ceiling/floor, front/rear
BNC ×1,
3G-SDI signal: SMPTE ST 424 compliant
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
HDMI 19-pin ×1, Deep Color, compatible with HDCP,
VGA (640 ×480) –WUXGA*4(1,920 ×1,200),
dot clock: 25 MHz–162 MHz
NOTE: Compatible with non-interlaced signals only.
DVI-D 24-pin ×1, DVI 1.0 compliant, HDCP compatible,
for single link only
525i(480i)*3, 625i(576i)*3, 525p(480p), 625p(576p), 750(720)/60p,
750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,
1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,
1125(1080)/50p
VGA (640 ×480) –WUXGA*4(1,920 ×1,200),
dot clock: 25 MHz–162 MHz
NOTE: Compatible with non-interlaced signals only.
BNC ×5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
D-sub HD 15-pin (female) ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC ×1, 1.0 Vp-p, 75 ohms
525i(480i)*3, 625i(576i)*3, 525p(480p), 625p(576p), 750(720)/60p,
750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,
1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,
1125(1080)/50p
REMOTE 2 IN
LAN
D-sub 9-pin ×1for external control (parallel)
RJ-45 ×1for network connection, 100Base-TX/10Base-T, compliant
with PJLink™ (class 1)
SERIAL IN
SERIAL OUT
REMOTE 1 IN
REMOTE 1 OUT
D-sub 9-pin (female) ×1for external control (RS-232C compliant)
D-sub 9-pin (male) ×1for link control
M3 jack ×1for wired remote control
M3 jack ×1for link control
(RS-232C compliant)
Power cord length
Cabinet materials
3.0 m (9 10 in)
Molded plastic
Dimensions (W ×H× D):
Weight*6
Operation noise*2
530 ×200*5×548.5 mm
(20-7/8 ×7-7/8*5× 21-19/32 inches) (without lens)
24 kg (52.9 lbs) (without lens)
43 dB (normal mode), 37 dB (eco mode)
Operating temperature
Operating humidity
0°– 45°C (32°–113°F)*7
10%–80% (no condensation)

As of April 2013
SFD12M023
4/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Remote control unit
Power supply
Operation range*8
Dimensions (W × H × D)
Weight
Supplied accessories
Optional accessories
Zoom lens (0.9– 1.1:1)
Zoom lens (1.3– 1.7:1)
Zoom lens (1.7– 2.4:1)
Zoom lens (2.4– 4.7:1)
Zoom lens (4.6– 7.4:1)
Zoom lens (7.3– 13.8:1)
Fixed-focus lens (0.7:1)
Lens motor cover
Ceiling mount bracket
Frame
Smoke cut filter
Replacement lamp unit
Replacement lamp unit for portrait mode
Replacement filter unit
3 V DC (AA/R6 type battery × 2)
Approx. 30 m (98 5 in) when operated from directly in front of the
signal receptor
51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches)
Approx. 134 g (4.7 oz) (including batteries)
Power cord (×1) (x2 for PT-DZ10KE)
Wireless/wired remote control unit (× 1)
Batteries for remote control (AA/R6 type × 2)
Softwar
Lens drop-prevention screw (× 1)
e CD-ROM (Logo Transfer Software, Multi Projector Monitoring
& Control Software) (× 1)
ET-D75LE6
ET-D75LE10
ET-D75LE20
ET-D75LE30
ET-D75LE40
ET-D75LE8
ET-D75LE50
ET-D75MC1
ET-PKD310H (for high ceilings)
ET-PKD310S (for low ceilings)
ET
Attachment for ceiling mount bracket ET-PAD310
-PFD310
ET
Replacement smoke cut filter ET-SFR320
-SFD320
ET-LAD310A (one bulb)
ET-LAD310AW (a set of two bulbs)
ET-LAD320P (one bulb)
ET-LAD320PW (a set of two bulbs)
ET-EMF320
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output termi-
nal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5 With legs at shortest position.
*6 Average value (excluding the optional lens). May differ depending on models.
*7 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from
1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature
range is 0 °C to 35 °C (32 °F to 95 °F), and the projector cannot be used in places at high altitude. The operating temperature range is 0 °C to 40 °C
(32 °F to 104 °F) when the ET-LAD320P/LAD320PW lamp is mounted and the projector is used in portrait configuration. The operating temperature
range is 0 °C to 35 °C (32 °F to 95 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to
8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 30 °C (32 °F
to 86 °F).
*8 Operation range differs depending on environments.

As of April 2013
SFD12M023
5/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Dimensions
Terminals
1Remote 1 input
2Remote 1 output
3Remote 2 input
4Serial input
5Serial output
6 SDI input
7HDMI input
8RGB 1 input
9RGB 2 Input
10 DVI-D input
11 Video input
12 LAN connector
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
540 (21-1/4)
548.5 (21-19/32)
8.5
(11/32)
530 (20-7/8)
462 (18-3/16) 468 (18-7/16)
26
(1-1/32)
100
(3-15/16)
200 (7-7/8)

As of April 2013
SFD12M023
6/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Standard setting-up position
unit : mm (inch)
*1 When the lens protrudes to the
maximum.
212 mm (8-11/32) with the ET-D75LE6
125 mm (4-29/32) with the ET-D75LE10
121 mm (4-3/4) with the ET-D75LE20
121 mm (4-3/4) with the ET-D75LE30
124 mm (4-7/8) with the ET-D75LE40
254 mm (10) with the ET-D75LE8
203 mm (8) with the ET-D75LE50
*2 Adjustable in 40 mm (1-9/16) steps.
Caution:
•All construction work should be done by a qualified technician.
•When mounting to the ceiling, use the special mounting bracket.
Furthermore, in order to prevent it from falling down from the ceiling, use the supplied wire on the mounting bracket.
NOTE:
Illustrations show the projector installed
using optional ceiling mount bracket
ET-PKD310H and an optional lens.
This illustration is not drawn to scale.
Projected image
H H
Lower edge of projected image
Upper edge of projected image
L
Projected image
L
L
*2
*
2
*1
340～420
436～516
342
(13-15/32)
198
(7-25/32)
φ60.5
(12-3/8)
100 (3-15/16)
100
(3-15/16)
100
(3-15/16)
100
(3-15/16)
(13-3/8–
16-17/32)
(17-5/32–
20-5/16)

As of April 2013
SFD12M023
7/17
[m] / [in]
/
/
/
/
/
/
/
/
/
/
/
/
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
10.16
12.70
15.24
70
80
90
100
120
150
200
250
300
400
500
600
Screen size
(diagonal) Zoom
Zoom lenses
Fixed-focus
Fixed-
focus
lens
Distance to screen (L) Height from the edge of screen
to center of lens (H)
ET-D75LE10
Zoom lens
min. max. min. max. min. max. min. max. min. max. min. max.
ET-D75LE6
Zoom lens
ET-D75LE20
Zoom lens
ET-D75LE30
Zoom lens
ET-D75LE40
Zoom lens
ET-D75LE8
Zoom lens
ET-D75LE50
Fixed-focus
lens
Except
ET-D75LE6
ET-D75LE6
–
–
–
–
–
–
–
–
–
–
–
–
0.06
0.07
0.07
0.08
0.10
0.12
0.16
0.20
0.24
0.32
0.40
0.49
0.89
1.01
1.14
1.27
1.52
1.90
2.53
3.16
3.80
5.06
6.33
7.59
–
–
–
–
–
–
–
–
–
–
–
–
-0.05
-0.05
-0.06
-0.07
-0.08
-0.10
-0.14
-0.17
-0.20
-0.27
-0.34
-0.40
0.99
1.13
1.27
1.41
1.70
2.12
2.83
3.53
4.24
5.65
7.07
8.48
1.01
1.16
1.32
1.47
1.78
2.24
3.01
3.78
4.56
6.10
7.64
9.18
0.47
0.54
0.61
0.67
0.81
1.01
1.35
1.68
2.02
2.69
3.37
4.04
1.62
1.86
2.10
2.34
2.82
3.55
4.75
5.96
7.17
9.58
11.99
14.40
2.46
2.83
3.20
3.56
4.30
5.40
7.24
9.07
10.91
14.58
18.25
21.93
3.58
4.11
4.64
5.17
6.22
7.81
10.45
13.09
15.73
21.01
26.29
31.58
6.94
7.96
8.98
9.99
12.03
15.08
20.17
25.25
30.34
40.51
50.68
60.85
11.05
12.65
14.25
15.85
19.05
23.85
31.86
39.86
47.87
63.87
79.88
95.89
20.56
23.55
26.54
29.53
35.51
44.47
59.41
74.36
89.30
119.19
149.08
178.96
1.35
1.56
1.76
1.96
2.36
2.96
3.97
4.98
5.99
8.00
10.01
12.03
1.90
2.19
2.47
2.76
3.32
4.18
5.60
7.02
8.44
11.28
14.12
16.96
2.46
2.83
3.19
3.55
4.28
5.37
7.19
9.01
10.82
14.46
18.09
21.73
3.56
4.08
4.61
5.13
6.18
7.75
10.38
13.00
15.62
20.86
26.11
31.35
6.87
7.88
8.88
9.88
11.89
14.90
19.93
24.95
29.97
40.01
50.05
60.09
10.78
12.38
13.97
15.57
18.76
23.54
31.52
39.49
47.47
63.42
79.37
95.32
/17.78 700
/20.32 800
/22.86 900
/25.40 1000
[m] / [in]
/
/
/
/
/
/
/
/
/
/
/
/
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
10.16
12.70
15.24
70
80
90
100
120
150
200
250
300
400
500
Screen size
(diagonal) Zoom
Zoom lenses
Fixed-focus
Fixed-
focus
lens
Distance to screen (L) Height from the edge of screen
to center of lens (H)
ET-D75LE10
Zoom lens
min. max. min. max. min. max. min. max. min. max. min. max.
ET-D75LE6
Zoom lens
ET-D75LE20
Zoom lens
ET-D75LE30
Zoom lens
ET-D75LE40
Zoom lens
ET-D75LE8
Zoom lens
ET-D75LE50
Fixed-focus
lens
Except
ET-D75LE6
ET-D75LE6
–
–
–
–
–
–
–
–
–
–
–
–
0.2
0.2
0.2
0.3
0.3
0.4
0.5
0.7
0.8
1.1
1.3
1.6
2.9
3.3
3.7
4.2
5.0
6.2
8.3
10.4
12.5
16.6
20.8
24.9
–
–
–
–
–
–
–
–
–
–
–
–
-0.2
-0.2
-0.2
-0.2
-0.3
-0.3
-0.4
-0.6
-0.7
-0.9
-1.1
-1.3
3.2
3.7
4.2
4.6
5.6
7.0
9.3
11.6
13.9
18.6
23.2
27.8
3.3
3.8
4.3
4.8
5.8
7.3
9.8
12.3
14.9
20.0
25.1
1.6
1.8
2.0
2.2
2.7
3.3
4.4
5.5
6.6
8.8
11.0
5.3
6.1
6.9
7.7
9.3
11.6
15.6
19.6
23.5
31.4
39.3
47.3
8.1
9.3
10.5
11.7
14.1
17.7
23.7
29.8
35.8
47.8
59.9
71.9
11.7
13.5
15.2
16.9
20.4
25.6
34.3
42.9
51.6
68.9
86.3
103.6
22.8
26.1
29.5
32.8
39.5
49.5
66.2
82.8
99.5
132.9
166.3
199.6
36.2
41.5
46.7
52.0
62.5
78.3
104.5
130.8
157.0
209.6
262.1
314.6
67.5
77.3
87.1
96.9
116.5
145.9
194.9
244.0
293.0
391.0
489.1
587.1
4.4
5.1
5.8
6.4
7.7
9.7
13.0
16.3
19.6
26.2
32.9
39.5
6.2
7.2
8.1
9.0
10.9
13.7
18.4
23.0
27.7
37.0
46.3
55.6
8.1
9.3
10.5
11.7
14.0
17.6
23.6
29.5
35.5
47.4
59.4
71.3
11.7
13.4
15.1
16.8
20.3
25.4
34.0
42.6
51.2
68.5
85.7
102.9
22.5
25.8
29.1
32.4
39.0
48.9
65.4
81.8
98.3
131.3
164.2
197.1
35.4
40.6
45.8
51.1
61.5
77.2
103.4
129.6
155.7
208.1
260.4
312.7
Projection distance for 16:10 aspect ratio screen
(ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50)
Unit: feet
Unit: meters
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
NOTE: When the ET-D75LE50 is mounted, the optical lens shift function cannot be used.
14.04 16.82 19.80 25.60 25.36 36.86 36.60 71.02 70.13 111.90 111.27 – 10.72 -0.47 – 9.90 0.57 – 8.86 4.71
16.06 19.23 22.64 29.27 29.00 42.14 41.84 81.19 80.17 127.91 127.23 – 12.27 -0.54 –11.31 0.65 –10.12 5.39
18.07 21.64 25.48 32.94 32.63 47.42 47.09 91.36 90.21 143.92 143.12 – 13.81 -0.61 –12.72 0.73 –11.39 6.06
20.08 24.06 28.33 36.61 36.27 52.70 52.33 101.53 100.25 159.93 159.13 – 15.35 -0.67 –14.14 0.81 –12.65 6.73
600 30.1 13.3
/17.78 700
/20.32 800
/22.86 900
/25.40 1000
46.1 55.2 65.0 84.0 83.2 120.9 120.1 233.0 230.1 367.1 365.1 – 35.2 -1.5 –32.5 1.9 – 29.1 15.5
52.7 63.1 74.3 96.0 95.1 138.3 137.3 266.4 263.0 419.6 417.4 – 40.2 -1.8 –37.1 2.1 – 33.2 17.7
59.3 71.0 83.6 108.1 107.1 155.6 154.5 299.7 296.0 472.2 469.5 – 45.3 -2.0 –41.7 2.4 – 37.4 19.9
65.9 78.9 92.9 120.1 119.0 172.9 171.7 333.1 328.9 524.7 522.1 – 50.4 -2.2 –46.4 2.7 – 41.5 22.1
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector

As of April 2013
SFD12M023
8/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
[m] / [in]
/
/
/
/
/
/
/
/
/
/
/
/
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
10.16
12.70
15.24
70
80
90
100
120
150
200
250
300
400
500
600
Screen size
(diagonal) Zoom
Zoom lenses
Fixed-focus
Fixed-
focus
lens
Distance to screen (L) Height from the edge of screen
to center of lens (H)
ET-D75LE10
Zoom lens
min. max. min. max. min. max. min. max. min. max. min. max.
ET-D75LE6
Zoom lens
ET-D75LE20
Zoom lens
ET-D75LE30
Zoom lens
ET-D75LE40
Zoom lens
ET-D75LE8
Zoom lens
ET-D75LE50
Fixed-focus
lens
Except
ET-D75LE6
ET-D75LE6
–
–
–
–
–
–
–
–
–
–
–
–
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.87
1.00
1.12
1.25
1.49
1.87
2.49
3.11
3.74
4.98
6.23
7.47
–
–
–
–
–
–
–
–
–
–
–
–
-0.09
-0.10
-0.11
-0.13
-0.15
-0.19
-0.25
-0.31
-0.37
-0.50
-0.62
-0.75
0.96
1.10
1.23
1.37
1.64
2.06
2.74
3.42
4.11
5.48
6.85
8.22
1.04
1.20
1.36
1.51
1.83
2.31
3.10
3.89
4.68
6.29
7.85
9.44
0.44
0.50
0.56
0.62
0.75
0.93
1.25
1.56
1.87
2.49
3.11
3.74
1.66
1.91
2.16
2.41
2.90
3.65
4.89
6.13
7.37
9.85
12.33
14.81
2.53
2.91
3.29
3.67
4.42
5.55
7.44
9.33
11.21
14.99
18.76
22.54
3.68
4.23
4.77
5.31
6.40
8.03
10.74
13.46
16.17
21.60
27.03
32.46
7.14
8.19
9.23
10.28
12.37
15.50
20.73
25.96
31.18
41.64
52.09
62.54
11.36
13.00
14.65
16.29
19.58
24.52
32.75
40.97
49.20
65.65
82.11
98.56
21.14
24.22
27.29
30.36
36.50
45.72
61.08
76.44
91.79
122.51
153.23
183.95
1.39
1.60
1.81
2.01
2.43
3.05
4.08
5.12
6.15
8.22
10.29
12.36
1.96
2.25
2.54
2.83
3.42
4.29
5.76
7.22
8.68
11.60
14.52
17.44
2.53
2.91
3.28
3.65
4.40
5.52
7.39
9.26
11.13
14.86
18.60
22.33
3.66
4.20
4.74
5.28
6.36
7.97
10.67
13.36
16.06
21.45
26.84
32.23
7.07
8.10
9.13
10.16
12.23
15.32
20.48
25.64
30.80
41.12
51.44
61.76
11.09
12.73
14.37
16.01
19.29
24.21
32.40
40.60
48.80
65.19
81.59
97.98
[m] / [in]
/
/
/
/
/
/
/
/
/
/
/
/
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
10.16
12.70
15.24
70
80
90
100
120
150
200
250
300
400
500
600
Screen size
(diagonal) Zoom
Zoom lenses
Fixed-focus
Fixed-
focus
lens
Distance to screen (L) Height from the edge of screen
to center of lens (H)
ET-D75LE10
Zoom lens
min. max. min. max. min. max. min. max. min. max. min. max.
ET-D75LE6
Zoom lens
ET-D75LE20
Zoom lens
ET-D75LE30
Zoom lens
ET-D75LE40
Zoom lens
ET-D75LE8
Zoom lens
ET-D75LE50
Fixed-focus
lens
Except
ET-D75LE6
ET-D75LE6
–
–
–
–
–
–
–
–
–
–
–
–
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
2.9
3.3
3.7
4.1
4.9
6.1
8.2
10.2
12.3
16.3
20.4
24.5
–
–
–
–
–
–
–
–
–
–
–
–
-0.3
-0.3
-0.4
-0.4
-0.5
-0.6
-0.8
-1.0
-1.2
-1.6
-2.0
-2.5
3.2
3.6
4.1
4.5
5.4
6.7
9.0
11.2
13.5
18.0
22.5
27.0
3.4
3.9
4.4
5.0
6.0
7.6
10.2
12.8
15.4
20.6
25.8
31.0
1.4
1.6
1.8
2.0
2.5
3.1
4.1
5.1
6.1
8.2
10.2
12.3
5.5
6.3
7.1
7.9
9.5
12.0
16.0
20.1
24.2
32.3
40.4
48.6
8.3
9.6
10.8
12.0
14.5
18.2
24.4
30.6
36.8
49.2
61.6
73.9
12.1
13.9
15.6
17.4
21.0
26.3
35.2
44.1
53.1
70.9
88.7
106.5
23.4
26.9
30.3
33.7
40.6
50.9
68.0
85.2
102.3
136.6
170.9
205.2
37.3
42.7
48.1
53.5
64.2
80.4
107.4
134.4
161.4
215.4
269.4
323.4
69.4
79.4
89.5
99.6
119.8
150.0
200.4
250.8
301.2
401.9
502.7
603.5
4.6
5.2
5.9
6.6
8.0
10.0
13.4
16.8
20.2
27.0
33.8
40.6
6.4
7.4
8.3
9.3
11.2
14.1
18.9
23.7
28.5
38.0
47.6
57.2
8.3
9.5
10.8
12.0
14.4
18.1
24.2
30.4
36.5
48.8
61.0
73.3
12.0
13.8
15.5
17.3
20.8
26.2
35.0
43.8
52.7
70.4
88.0
105.7
23.2
26.6
30.0
33.3
40.1
50.3
67.2
84.1
101.1
134.9
168.8
202.6
36.4
41.8
47.1
52.5
63.3
79.4
106.3
133.2
160.1
213.9
267.7
321.5
Projection distance for 16:9 aspect ratio screen
(ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50)
Unit: feet
Unit: meters
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
NOTE: When the ET-D75LE50 is mounted, the optical lens shift function cannot be used.
/17.78 700
/20.32 800
/22.86 900
/25.40 1000
47.4 56.7 66.8 86.3 85.5 124.3 123.4 239.5 236.5 377.3 375.3 – 36.2 -2.9 –31.5 0.0 – 28.6 14.3
54.1 64.8 76.4 98.7 97.8 142.1 141.1 273.8 270.5 431.3 429.0 – 41.4 -3.3 –36.0 0.0 – 32.7 16.3
60.9 73.0 85.9 111.1 110.0 159.9 158.8 308.1 304.2 485.3 482.8 – 46.6 -3.7 –40.4 0.0 – 36.8 18.4
67.7 81.1 95.5 123.5 122.3 177.7 176.5 342.4 338.1 539.3 536.6 – 51.8 -4.1 –44.9 0.0 – 40.9 20.4
/17.78 700
/20.32 800
/22.86 900
/25.40 1000
14.43 17.29 20.36 26.31 26.07 37.89 37.62 73.00 72.09 115.02 114.38 – 11.02 -0.87 – 9.59 0.00 – 8.72 4.36
16.50 19.77 23.28 30.09 29.81 43.31 43.01 83.45 82.45 131.47 130.77 – 12.61 -1.00 –10.96 0.00 – 9.96 4.98
18.57 22.25 26.20 33.86 33.54 48.74 48.40 93.90 92.73 147.92 147.17 – 14.19 -1.12 –12.33 0.00 –11.21 5.60
20.64 24.73 29.12 37.64 37.28 54.17 53.79 104.36 103.05 164.38 163.56 – 15.78 -1.25 –13.70 0.00 –12.45 6.23

As of April 2013
SFD12M023
9/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 16:10
minimum L (m) = (diagonal screen size in inches) × 0.0201 – 0.0566
maximum L (m) = (diagonal screen size in inches) × 0.0241 – 0.0736
minimum L (m) = (diagonal screen size in inches) × 0.0284 – 0.0857
maximum L (m) = (diagonal screen size in inches) × 0.0367 – 0.1085
minimum L (m) = (diagonal screen size in inches) × 0.0364 – 0.0832
maximum L (m) = (diagonal screen size in inches) × 0.0528 – 0.1162
minimum L (m) = (diagonal screen size in inches) × 0.0524 – 0.1131
maximum L (m) = (diagonal screen size in inches) × 0.1017 – 0.1765
minimum L (m) = (diagonal screen size in inches) × 0.1004 – 0.1577
maximum L (m) = (diagonal screen size in inches) × 0.1601 – 0.1615
minimum L (m) = (diagonal screen size in inches) × 0.1595 – 0.3862
maximum L (m) = (diagonal screen size in inches) × 0.2989 – 0.3598
L (m) = (diagonal screen size in inches) × 0.0154 – 0.0713
Zoom lenses
ET-D75LE6
ET-D75LE10
ET-D75LE20
ET-D75LE30
ET-D75LE40
ET-D75LE8
Fixed-focus lens
ET-D75LE50
Aspect ratio 16:9
minimum L (m) = (diagonal screen size in inches) × 0.0207 – 0.0566
maximum L (m) = (diagonal screen size in inches) × 0.0248 – 0.0736
minimum L (m) = (diagonal screen size in inches) × 0.0292 – 0.0857
maximum L (m) = (diagonal screen size in inches) × 0.0377 – 0.1085
minimum L (m) = (diagonal screen size in inches) × 0.0374 – 0.0832
maximum L (m) = (diagonal screen size in inches) × 0.0543 – 0.1162
minimum L (m) = (diagonal screen size in inches) × 0.0539 – 0.1131
maximum L (m) = (diagonal screen size in inches) × 0.1045 – 0.1765
minimum L (m) = (diagonal screen size in inches) × 0.1032 – 0.1577
maximum L (m) = (diagonal screen size in inches) × 0.1645 – 0.1615
minimum L (m) = (diagonal screen size in inches) × 0.1640 – 0.3862
maximum L (m) = (diagonal screen size in inches) × 0.3072 – 0.3598
L (m) = (diagonal screen size in inches) × 0.0159 – 0.0713
Zoom lenses
ET-D75LE6
ET-D75LE10
ET-D75LE20
ET-D75LE30
ET-D75LE40
ET-D75LE8
Fixed-focus lens
ET-D75LE50
• Distances calculated with the above equations will include slight deviations.

As of April 2013
SFD12M023
10/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
H
(Width of
projected image)
V
(Height of
projected image)
0.12V
0.55V
0.55V
0.12V
0.2H0.2H
Standard postition of projected image
-15°
+15°
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
Installable angle
Install the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical
angle of 360°.
• Horizontal direction
The projector may be installed at a horizontal
angle of ±15°.
+15°
-15°
-15°
+15°
• Vertical direction in portrait mode with the
ET-LAD320P/LAD320PW mounted
The projector may be installed at a vertical
angle of ±15°.
• Horizontal direction in portrait mode with
the ET-LAD320P/LAD320PW mounted
The projector may be installed at a horizontal
angle of ±15°.
• When the lens except the ET-D75LE6 is mounted
H
(Width of
projected image)
V
(Height of
projected image)
0.12V
0.44V
0.44V
0.12V
0.15H0.15H
Standard postition of projected image
• When the ET-D75LE6 is mounted
NOTE: Because the ET-D75LE50 is a fixed short-throw lens, the lens shift function cannot be used with it.
NOTE: The projector cannot be vertically installed all by itself. Also, the terminal side must face downward when vertically installed.
360°

As of April 2013
SFD12M023
11/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
List of compatible signals
The signals that can be input to this projector are shown in the table below. Horizontal scanning fre-
quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of
162 MHz maximum can be input.
NOTE: The native resolution of this projector is 1,920 × 1,200 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)*1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Format
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720 × 483
720 × 576
1280 × 720
1920 × 1080i
1920 × 1080
1920 × 1080i
1920 × 1080
640 × 400
640 × 480
800 × 600
832 × 624
1024 × 768
1152 × 864
1152 × 870
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
27.0
28.1
33.8
67.5
56.3
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
65.5
68.7
81.4
98.8
53.7
64.0
67.5
76.7
68.7
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
24.0
27.0 48.0
25.0
30.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.0
60.0
70.1
75.0
81.6
85.0
100.0
120.0
60.0
70.0
74.9
85.0
75.1
−
−
13.5
13.5
27.0
74.3
148.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
86.0
94.5
113.3
139.1
81.6
94.2
108.0
121.5
100.0
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
525i (480i)
625i (576i)
525p (480p)
625p (576p)
750 (720)/60p
750 (720)/50p
1125 (1080)/60i
1125 (1080)/50i
1125 (1080)/24p
1125 (1080)/24sF
1125 (1080)/25p
1125 (1080)/30p
1125 (1080)/60p
1125 (1080)/50p
VGA400
VGA480
SVGA
MAC16
XGA
MXGA
MAC21
VIDEO/S-VIDEO
SDI/RGB/YCBCR
720(1440) × 480i
720(1440) × 576i
15.7
15.6
59.9
50.0
27.0
525i (480i)
625i (576i)
HDMI/DVI-D
HDMI/DVI-D/
RGB/YCBCR
SDI/HDMI/DVI-D/
RGB/YPBPR
SDI/HDMI/DVI-D/
RGB/YPBPR
HDMI/DVI-D/RGB
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2 Pixel repetition signal only.
*2
*2

As of April 2013
SFD12M023
12/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Display mode Display
resolution
(dots)
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Format
1280 × 720
1280 × 768
1280 × 768
1280 × 768
1280 × 800
1280 × 800
1280 × 800
1280 × 960
1280 × 1024
1366 × 768
1400 × 1050
1440 × 900
1600 × 1200
1680 × 1050
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1200
1920 × 1200
1920 × 1200
37.1
44.8
76.3
92.6
39.6
47.8
47.4
60.3
68.6
41.3
49.7
49.3
62.8
71.6
60.0
52.4
64.0
72.3
78.2
80.0
91.1
47.7
39.6
54.1
64.0
65.2
65.3
78.8
82.2
55.9
46.3
75.0
65.3
54.1
55.6
66.6
67.2
61.8
74.0
74.6
49.8
59.9
100.0
120.0
49.9
59.9
60.0
74.9
84.8
50.0
59.8
59.9
74.9
84.9
60.0
50.0
60.0
66.3
72.0
75.0
85.0
59.8
49.9
50.0
60.0
60.0
60.0
72.0
75.0
59.9
49.9
60.0
50.0
49.9
59.9
60.0
49.9
60.0
59.9
60.5
74.5
131.8
161.6
65.3
79.5
68.3
102.3
117.5
68.0
83.5
71.0
106.5
122.5
108.0
88.0
108.0
125.0
135.1
135.0
157.5
85.5
69.0
99.9
108.0
122.6
121.8
149.3
155.9
106.5
86.8
162.0
146.3
119.5
141.5
138.5
173.0
158.3
154.0
193.3
1280 × 720
1280 × 768
1280 × 800
MSXGA
SXGA
1366×768
SXGA+
WXGA+
UXGA60
WSXGA+
1920×1080
WUXGA
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D/RGB
RGB
*
*
*
*
*Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
60.0

As of April 2013
SFD12M023
13/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
D-sub 9-pin (female) Serial input
Description
NC
Send data
Receive data
NC
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
Pin assignments and signal names
D-sub 9-pin (male) Serial output
Description
NC
Receive data
Send data
NC
Ground
Signal name
–
RXD
TXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
RTS
CTS
–
No.
6
7
8
9
CAUTION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this
occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before
sending the next command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for com-
mand response to 10 seconds or more.
• When using two or more units:
1) Set different IDs for each unit.
2) Designate only one unit as RESPONSE (ID ALL) ON and the rest as RESPONSE (ID ALL) OFF.
3) Each group should have only one RESPONSE (ID GROUP) ON and the rest should be RESPONSE (ID GROUP) OFF.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte)
Semicolon
(1 byte)
(2 byte)
ID designator
01 to 64: Address number
0A to 0Z: Group ID
ZZ: All units (ID ALL)
ID: 2 characters
(2 bytes) Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
STX ETXC1 P1 P2 ... PnC2A D I1 I2 C3 :;
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None

As of April 2013
SFD12M023
14/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Control commands
Command : Parameter Function Callback
PON
POF
IIS:SD1
IIS:HD1
IIS:DVI
IIS:RG1
IIS:RG2
IIS:VID
LPM:0
LPM:1
LPM:2
LPM:3
VXX:RYC1=+00000
VXX:RYC1=+00001
OLP:0
OLP:1
VSE:1
VSE:2
VSE:5
VSE:6
VSE:10
OSH:0
OSH:1
OPP:0
OPP:1
OPP:2
OPP:3
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VPM:DIC
VXX:DLVI0=+00000
VXX:DLVI0=+00001
VXX:DLVI0=+00002
VXX:DLVI0=+00003
OTE:4
OTE:9
OTE:10
OTE:p1p2p3p4
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:0
OOS:1
Standby power on
Standby power off
SDI 1
HDMI
DVI
RGB 1
RGB 2
Video
Dual (two lamps)
Single lamp
Lamp 1
Lamp 2
RGB/Y・PB・PR
S-Video
Normal
Eco
Standard/VID Auto
4:3
16:9
HV fit
V fit
Shutter off
Shutter on
Off
User 1
User 2
User 3
Natural
Standard
Dynamic
Cinema
Graphic
DICOM
Off
1
2
3
User 1
User 2
Default
3200 K – 9300 K (100 K steps)
Date setting
Time setting
On-screen display off
On-screen display on
POWER (STANDBY)
INPUT SELECT
LAMP SELECT
Lamp power
ASPECT RATIO
SWITCHING
RGB INPUT SETTING
SHUTTER
P IN P SELECT
AUTO SETUP
PICTURE MODE
SYSTEM DAYLIGHT VIEW
COLOR TEMPERATURE
DATE
TIME
ON SCREEN
PON
POF
IIS:SD1
IIS:HD1
IIS:DVI
IIS:RG1
IIS:RG2
IIS:VID
LPM:0
LPM:1
LPM:2
LPM:3
VXX:RYC1=+00000
VXX:RYC1=+00001
OLP:0
OLP:1
VSE:1
VSE:2
VSE:5
VSE:6
VSE:9 H fit VSE:9
VSE:10
OSH:0
OSH:1
OPP:0
OPP:1
OPP:2
OPP:3
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VPM:DIC
VXX:DLVI0=+00000
VXX:DLVI0=+00001
VXX:DLVI0=+00002
VXX:DLVI0=+00003
OTE:4
OTE:9
OTE:10
OTE:p1p2p3p4
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:0
OOS:1
Cable specifications
* Do not send PON, POF, OSH, or OLP commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp
replacement cycle.
* When a command that cannot be executed, the projector will send an ER401 command in reply.

As of April 2013
SFD12M023
15/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Status request commands
Command:Parameter Function DescriptionCallback
QPW
QSH
QIN
QOS
QST
Q$L:1
Q$L:2
QSL
QPM
QVX:DLVI0
QPP
QTM:0
QTM:1
QTM:2
QGD
QGT
Main power status
Shutter function status
Input signal status
On-screen display status
Projector run time
Lamp 1 run time
Lamp 2 run time
Lamp operation mode status
Picture mode status
System daylight view status
P in P status
Temperature status
Date setting status
Time setting status
Off
On
Off
On
SDI
DVI
RGB 1
RGB 2
Video
Off
On
00000h–99999h
0000h–9999h
0000h–9999h
Dual (two lamps)
Single lamp
Natural
Standard
Dynamic
Cinema
Graphic
DICOM
Off
1
2
3
Off
User 1
User 2
User 3
p0 = Intake air
p1 = Around lamp
p2 = Optics module
yyyymmdd (day of week)*2
hhmmss *3
000
001
0
1
SD1
DVI-D
RG1
RG2
VID
0
1
Normal
Eco
0
QLP Lamp power mode status
1
p1p2p3p4p5
p1p2p3p4
p1p2p3p4
0
1
NAT
STD
DYN
CIN
GRA
DIC
DLVI0=+00000
DLVI0=+00001
DLVI0=+00002
DLVI0=+00003
0
1
2
3
p1p2p3p4/p5p6p7p8*1
y1y2y3y4m1m2d1d2w
h1h2m1m2s1s2
*1 p1p2p3p4: Celsius (°C), p5p6p7p8: Fahrenheit (°F)
*2 Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
*3 Set the date and time to UTC (universal time coordinated).
*When a wrong command is sent, the projector will send an ER401 or ER402 command in reply.
Command example
To set the on-screen display off, send the command as shown below.
ADZZ OOS : 0; ETX
ID Address Command
STX
Start Parameter End
NOTE: When sending commands without parameters, a colon (:) is not necessary.

As of April 2013
SFD12M023
16/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
500 mm (19-11/16˝ ) or more 500 mm (19-11/16˝ )
or more
500 mm (19-11/16˝ )
or more
Do not stack pr Do not support
the projector unit
by its top while
it is in use.
ojector
units directly on top of
one another.
100 mm
(3-15/16 in)
or more
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings.
3. Do not stack projector units directly on top of one another. If two units must be stacked for backup
use in ordinary projection, use a method as shown below and provide ample space between the
units to ensure that exhaust heat does not accumulate near the intake opening or around the units.
Dual stacked projection is not recommended.
4. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the projector
so that cool or hot air from other air conditioning equipment does not flow directly toward the
projector’s air intake or exhaust openings.
5. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
6. If the projector is installed in an enclosed space, ensure that the temperature of the air surrounding
the projector is between 0 °C and 45 °C (32 °F and 104 °F). Also make sure that the projector’s intake
and exhaust openings are not blocked. Even though the air surrounding the projector is 40 °C
(104 °F) or less, if hot exhaust air accumulates inside the space, it may cause the projector’s protective
circuit to interrupt projector operation. Pay particular attention to the surrounding temperature
conditions when planning the installation.
7. If the projector is not to be set on the floor using adjuster legs, install it by using the five ceilingmount
screw holes (screw diameter: M6, length of each screw hole in the projector: 16 mm (5/8˝)).
Provide a space of 5 to 10 mm (3/16˝ to 13/32˝) between the projector and the mounting surface by
inserting metal spacers.
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI

As of April 2013
SFD12M023
17/17
SPEC FILE
PT-DZ10K
3-Chip DLP™Projector
Operating the projector continuously
1. If the projector is to be operated continuously one week, use the dual-lamp optical system’s alternating lamp
operation (lamp relay) function. The projector cannot be operated continuously one week in dual-lamp mode.
Allow a minimum of two hours per day of non-operation time for each lamp if the projector is to be operated
continuously for more than one week.
2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods.
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
Product availability differs depending on region and country. This product may be subject to export control regulations.
DLP and the DLP logo are trademarks of Texas Instruments.
P
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
JLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.
All other trademarks are the property of their respective trademark owners.
Direction of air intake and exhaust
Intake
Exhaust
SHUTTER
SHUTTER
LENS
LENS
ENTER
ENTER
AUTO
AUTO
MENU
MENU
SETUP
SETUP
VIDEO
VIDEO
S-VIDEO
S-VIDEO
RGB1
RGB1
RGB2
RGB2
DVI-D/HDMI
DVI-D/HDMI
SDI
SDI