Panasonic PT-DZ570 Series System manual

SPEC FILE
Product Number : PT-DZ570
Product Name : DLP™Projector
A of May 2011. Specification and appearance are ubject to change without notice.
SFD10M012-1
1/14

SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
2/14
Specifications
Main unit
Power supply
Power consumption
DLP™ chip Panel size
Display method
Pixels
Lens
Throw ratio 16:10 aspect ratio
16:9 aspect ratio
Lamp
Screen size
Brightness*2
Center-to-corner uniformity*2
Contrast*2
Resolution
Scanning frequency HDM /DV -D
RGB
YPBPR(YCBCR)
Video/S-Video
Optical axis shift
Keystone correction range
nstallation
Terminals HDM N
DV -D N
RGB 1 N
R, G, B
Y, PB, PR(Y, CB, CR)
100–240 V AC, 5.0–1.9 A, 50/60 Hz
415 W (500 VA)
(0.3 W at 100 –120 V AC, 0.4 W at 220–240 V AC with standby mode
set to eco*1, 15 W with standby mode set to normal. Both with fan
stopped.)
17.0 mm (0.67 inches) diagonal (16:10 aspect ratio)
DLP™ chip × 1, DLP™ system
2,304,000 (1,920 × 1,200) × 1, total of 2,304,000 pixels
Manual zoom (2× zoom), manual focus F 2.0– 3.4, f 21.5– 43.0 mm
1.45–2.94:1
1.46–2.94:1
300 W (max. 310 W) UHM lamp
1.02–7.62 m (40–300 inches), 16:10 aspect ratio
4,000 lumens (lamp mode: normal)
90%
2,000:1 (full on/full off)
1,920 × 1,2 00 pixels
fH: 27 kHz–100 kHz, fV: 24Hz–120 Hz, dot clock: 25 MHz–162 MHz
fH: 15 kHz –100 kHz, fV: 24Hz–120 Hz, dot clock: 162 MHz or lower
480i (525i): fH15.75 kHz; fV60 Hz,
576i (625i): fH15.63 kHz; fV50 Hz,
480p (525p): fH31.50 kHz; fV60 Hz,
576p (625p): fH31.25 kHz; fV50 Hz,
720 (750)/60p: fH45.00 kHz; fV60 Hz,
720 (750)/50p: fH37.50 kHz; fV50 Hz,
1035/60i: fH33.75 kHz; fV60 Hz,
1080 (1125)/60i: fH33.75 kHz; fV60 Hz,
1080 (1125)/50i: fH28.13 kHz; fV50 Hz,
1080/25p: fH28.13 kHz; fV25 Hz,
1080/24p: fH27.00 kHz; fV24 Hz,
1080/24sF: fH27.00 kHz; fV48 Hz,
1080/30p: fH33.75 kHz; fV30 Hz,
1080/60p: fH67.50 kHz; fV60 Hz,
1080/50p: fH56.25 kHz; fV50 Hz
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Vertical: +60% (manual), horizontal: ±10% (manual)
Vertical: ±40°
Ceiling/floor, front/rear
HDM 19-pin ×1
Deep Color, HDCP compatible
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 × 480) – WUXGA*3(1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25 MHz–162 MHz
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz,
32 kHz)
DV -D 24-pin ×1
DV 1.0 compliant, HDCP compatible, for single link only
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 × 480) – WUXGA*3(1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25 MHz–162 MHz
BNC × 5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD/VD, SYNC: High impedance, TTL (positive/negative)
N TE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms

SPEC FI L E
PT-DZ570
D P™Projector
As of May 2011
SFD10M012-1
3/14
RGB 2 IN
R, G, B
Y, PB, PR(Y, CB, CR)
VIDEO IN
S-VIDEO IN
AUDIO IN 1
AUDIO IN 2
AUDIO IN 3
AUDIO OUT
SERIA IN
REMOTE IN
AN
WIRE ESS MODU E
Power cord length
Cabinet materials
Dimensions (W ×H×D)
Weight
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range *6
Dimensions (W × H × D)
Weight
Supplied accessories
Optional accessories
Replacement lamp unit
Ceiling mount bracket
Wireless module
D-sub HD 15-pin ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD/VD, SYNC: High impedance, TT (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
Mini DIN 4-pin × 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
RCA × 2 ( , R × 1), 0.5 Vrms
M3 × 1 ( , R × 1), 0.5 Vrms
M3 × 1 ( , R × 1), 0.5 Vrms
M3 × 1 ( , R × 1) (monitor out: 0–2.0 Vrms, variable)
D-sub 9-pin × 1 for external control (RS-232C compliant)
D-sub 9-pin × 1 for external control (parallel)
RJ-45 × 1 for network connection, 100Base-TX/10Base-T, compliant
with PJ ink™
Connector for optional wireless module ET-WM200U/WM200E ×1
3.0 m (9 ft 10 in)
Molded plastic (PC + ABS)
332 mm × 168 mm*4× 484.5 mm*5
(13-1/16˝ × 6-5/8˝*
4× 19-1/16˝* 5)
Approx. 8.5 kg (18.7 lbs)
0°–45°C (32°–113°F)
20%–80% (no condensation)
3 V DC (R6/ R6/AA type battery × 2)
Approx. 15 m (49 ft 3 in) when operated from directly in front of the
signal receptor
48 × 163 × 24.5 mm (1-7/8˝ × 6-13/32˝ × 31/32˝)
Approx. 117 g (4.1 oz) (including batteries)
Power cord with security lock (× 1)
Wireless remote control unit (× 1)
Batteries for remote control (R6/ R6/AA type × 2)
Wire rope (× 1)
Software CD-ROM ( ogo Transfer Software, Multi Projector Monitoring
and Control Software Ver. 2, Wireless Manager ME 5.5) (× 1)
ET- AD60A
ET- AD60AW (Twin Pack)
ET-PKD110H (for high ceilings)
ET-PKD110S (for low ceilings)
ET-WM200U (for North America)
ET-WM200E (for Europe and Asia)
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate. Also, only certain com-
mands can be received for external control using the serial terminal.
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 Compliant with VESA CVT-RB.
*4 With legs at shortest position.
*5 Including the lens.
*6 Operation range differs depending on environments.
*7 The operation system must be pre-installed at the factory or clean installed.

484.5 (19-1/16)
425 (16-23/32)59.5
(2-11/32)
9 (11/32) 7 (9/32)
332 (13-1/16)
90
(3-17/32)
165 (6-1/2) 168 (6-5/8)
Dimensions
unit : mm (inch)
N TE: This illustration is not drawn to scale.
SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
4/14
Terminals
12345
8911
10 12 13
67
1 LAN connector
2 HDM input
3 Video input
4 S-Video input
5 RGB 1 input
6 RGB 2 nput
7 DV -D input
8 Audio 1 input
9 Audio 2 input
10 Audio 3 input
11 Audio out put
12 Remote input
13 Serial input

SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
5/14
Standard setting-up position
Upper edge of projected image
230
(9-1/16˝)
253.5
(9-31/32˝)
∅60.5
(2-3/8˝)
*
Lower edge of projected image
Projected image
L
L
L
340–420
(13-3/8˝–
16-17/32˝)
431–511
(16-31/32˝–
20-1/8˝)
100 (3-15/16˝)
344
(13-17/32˝)
100
(3-15/16˝)
300
(11-13/16˝)
Projected image
HH
ET-PKD110H
ET-PKD110H
unit : mm (inch)
* Adjustable in 40 mm (1-9/16˝) steps.
Caution:
• All construction work should be done by a qualified technician.
• When mounting to the ceiling, use the special mounting bracket. To prevent the projector from swaying or drop-
ping, attach the wire that is included with the projector between the mounting bracket and the ceiling.
1.02 m
1.27 m
1.52 m
1.78 m
2.03 m
2.29 m
2.54 m
3.05 m
3.81 m
5.08 m
6.35 m
7.62 m
1.23
1.55
1.87
2.19
2.51
2.83
3.15
3.79
4.75
6.35
7.95
9.55
2.51
3.15
3.79
4.43
5.07
5.70
6.34
7.62
9.53
12.73
15.92
19.11
-0.05
-0.07
-0.08
-0.09
-0.11
-0.12
-0.14
-0.16
-0.20
-0.27
-0.34
-0.40
0.27
0.34
0.40
0.47
0.54
0.61
0.67
0.81
1.01
1.35
1.68
2.02
–
–
–
–
–
–
–
–
–
–
–
–
40˝
50˝
60˝
70˝
80˝
90˝
100˝
120˝
150˝
200˝
250˝
300˝
/
/
/
/
/
/
/
/
/
/
/
/
(4.1)
(5.1)
(6.2)
(7.2)
(8.3)
(9.3)
(10.4)
(12.5)
(15.6)
(20.9)
(26.1)
(31.4)
(8.2)
(10.3)
(12.4)
(14.5)
(16.6)
(18.7)
(20.8)
(24.9)
(31.2)
(41.7)
(52.2)
(62.6)
(-0.2
(-0.2
(-0.3
(-0.3
(-0.4
(-0.4
(-0.4
(-0.5
(-0.7
(-0.9
(-1.1
(-1.3
0.9)
1.1)
1.3)
1.5)
1.8)
2.0)
2.2)
2.7)
3.3)
4.4)
5.5)
6.6)
–
–
–
–
–
–
–
–
–
–
–
–
Projection size
[diagonal]
Projection distance [L]
Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens [ H]
Projection distance for 16:10 aspect ratio screen
unit: meters (feet)
N TE:
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
N TE:
Illustrations show the projector installed
using optional ceiling mount bracket.
This illustration is not drawn to scale.

SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
6/14
N TE:
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 16:10
minimum L (m) = (diagonal screen size in inches) × 0.0320 – 0.0546
maximum L (m) = (diagonal screen size in inches) × 0.0638 – 0.0408
Aspect ratio 16:9
minimum L (m) = (diagonal screen size in inches) × 0.0329 – 0.0546
maximum L (m) = (diagonal screen size in inches) × 0.0656 – 0.0408
N TE: Distances calculated with the above equations will include a slight error.
1.02 m
1.27 m
1.52 m
1.78 m
2.03 m
2.29 m
2.54 m
3.05 m
3.81 m
5.08 m
6.35 m
7.62 m
1.26
1.59
1.92
2.25
2.58
2.91
3.24
3.90
4.88
6.53
8.17
9.82
2.58
3.24
3.89
4.55
5.21
5.86
6.52
7.83
9.80
13.08
16.36
19.64
-0.08
-0.10
-0.13
-0.15
-0.17
-0.19
-0.21
-0.25
-0.31
-0.42
-0.52
-0.62
0.25
0.31
0.37
0.44
0.50
0.56
0.62
0.75
0.93
1.25
1.56
1.87
–
–
–
–
–
–
–
–
–
–
–
–
(4.2)
(5.3)
(6.3)
(7.4)
(8.5)
(9.6)
(10.7)
(12.8)
(16.1)
(21.5)
(26.9)
(32.3)
(8.4)
(10.6)
(12.7)
(14.9)
(17.0)
(19.2)
(21.3)
(25.6)
(32.1)
(42.9)
(53.6)
(64.4)
40˝
50˝
60˝
70˝
80˝
90˝
100˝
120˝
150˝
200˝
250˝
300˝
/
/
/
/
/
/
/
/
/
/
/
/
(-0.3
(-0.3
(-0.4
(-0.5
(-0.5
(-0.6
(-0.7
(-0.8
(-1.0
(-1.4
(-1.7
(-2.0
0.8)
1.0)
1.2)
1.4)
1.6)
1.8)
2.0)
2.5)
3.1)
4.1)
5.1)
6.1)
–
–
–
–
–
–
–
–
–
–
–
–
Projection size
[diagonal] Projection distance [L] Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens [H]
Projection distance for 16:9 aspect ratio screen
unit: meters (feet)

SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
7/14
H
(Width of
projected image)
V
(Height of
projected image)
0.46V
0.6V
0.1H0.1H
Standard postition
of projected image
H
(Width of
projected image)
V
(Height of
projected image)
0.46V
0.6V
0.1H0.1H
Standard postition
of projected image
360°
-15°
+15°
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
Installable angle
nstall the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical
angle of 360°.
• Horizontal direction
The projector may be installed at a horizontal
angle of ±15°.
• Floor mount • Ceiling mount

SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
8/14
List of compatible signals
The signals that can be input to this projector are shown in the table below. Horizontal scanning fre-
quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of
162 MHz maximum can be input.
N TE: The native resolution of this projector is 1,920 × 1,200 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)*1
Scanning frequency
H
(kHz) V (kHz)
Dot clock
frequency
(MHz)
Format
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720 × 483
720 × 576
1280 × 720
1280 × 720
1920 × 1080i
1920 × 1080i
1920 × 1080
1920 × 1080i
1920 × 1080
640 × 400
640 × 480
800 × 600
832 × 624
1024 × 768
1152 × 864
1152 × 870
1280 × 720
1280 × 768
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
27.0
27.0
28.1
33.8
67.5
56.3
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
65.5
68.7
80.0
96.7
53.7
64.0
67.5
76.7
68.7
37.1
44.8
39.6
47.8
47.4
60.3
68.6
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
24.0
24.0
50.0
60.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.0
60.0
70.1
75.0
81.6
85.0
100.0
120.0
60.0
71.2
74.9
85.0
75.1
49.8
59.9
49.9
59.9
60.0
74.9
84.8
−
−
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
74.3
74.3
74.3
74.3
148.5
148.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
86.0
94.5
105.0
130.0
81.6
94.2
108.0
121.5
100.0
60.5
74.5
65.3
79.5
68.3
102.3
117.5
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720/60p
720/50p
1080/60i
1080/50i
1080/24p
1080/24sF
1080/25p
1080/30p
1080/60p
1080/50p
VGA400
VGA480
SVGA
MAC16
XGA
MXGA
MAC21
1280 × 720
1280 × 768
1280 × 768*2
1280 × 768
VIDEO/S-VIDEO
SDI/RGB/YPBPR
HDMI/DVI-D/
RGB/YPBPR
HDMI/DVI-D/RGB
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
9/14
Display mode Display
resolution
(dots)*1
Scanning frequency
H
(kHz) V (kHz)
Dot clock
frequency
(MHz)
Format
1280 x 800
1280 x 960
1280 × 1024
1280 × 768
1400 × 1050
1440 × 900
1600 × 1200
1680 × 1050
1920 × 1080
1920 × 1200
41.3
49.7
49.3
62.8
71.6
60.0
52.4
64.0
72.3
78.2
80.0
91.1
47.7
39.6
54.1
64.0
65.2
65.3
78.8
82.2
55.9
46.3
75.0
65.3
54.1
55.6
66.6
67.2
61.8
74.0
74.6
50.0
59.8
59.9
74.9
84.9
60.0
50.0
60.0
66.3
72.0
75.0
85.0
59.8
49.9
50.0
60.0
60.0
60.0
72.0
75.0
59.9
49.9
60.0
60.0
50.0
49.9
59.9
60.0
49.9
60.0
59.9
68.0
83.5
71.0
106.5
122.5
108.0
88.0
108.0
125.0
135.1
135.0
157.5
84.8
69.0
99.9
108.0
122.6
121.8
149.3
155.9
106.5
86.8
162.0
146.3
119.5
141.5
138.5
173.0
158.3
154.0
193.3
1280 × 800
1280 × 800*2
1280 × 800
MSXGA
SXGA
1366×768
SXGA+
WXGA+
UXGA60
WSXGA+
1920×1080
1920×1080*2
1920×1080
WUXGA
WUXGA*2
WUXGA
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D/RGB
RGB
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking

SPEC FI L E
PT-DZ570
DLP™Projector
As of May 2011
SFD10M012-1
10/14
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then the D, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
6
15
9
D-sub 9-pin (female)
Serial input
Description
NC
Send data
Receive data
Connected internally
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
CAUTI N
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 sec-
onds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next
command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10
seconds or more.
• When using two or more units, set different IDs for each unit.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte)
Semicolon
(1 byte)
(2 byte)
ID designator
01 to 06: Address number
ZZ: All units (ID ALL)
ID: 2 characters
(2 bytes) Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
STX ETXC1P1P2...PnC2ADI1I2 C3:;
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None