Panasonic PT-RZ475 series User manual

1/12
Product Name : DLP™Projector
SPEC FILE
Product Number : PT-RZ475
As of May 2013. Specifications and appearance are subject to change without notice.
SFD13M007

SPEC FILE
DLP™Projectors
2/12
Main unit
Power supply
Power consumption
DLP™ chip Panel size
Display method
Pixels
Lens
Throw ratio
Light source
Screen size
Brightness*3
Center-to-corner uniformity*3
Contrast*3
Resolution
Scanning frequency HDMI/DVI-I (digital)
DVI-I (analog)/RGB
YPBPR(YCBCR)
Video
Optical axis shift
Keystone correction range
Installation
Terminals HDMI IN
DVI-I IN
Digital
R, G, B
Y, P B, PR(Y, CB, CR)
100 – 240 V AC, 5.0– 1.8 A, 50/60 Hz
430 W (440 VA)
(230 W*1with LIGHT POWER set to NORMAL/Eco1,
170 W*1with LIGHT POWER set to Eco2. 0.5 W with
STANDBY MODE set to ECO*2, 8 W with STANDBY MODE set to NORMAL)
16.5 mm (0.65 in) diagonal (16:9 aspect ratio)
DLP™ chip × 1, DLP™ system
2,073,600 (1,920 × 1,080) × 1, total of 2,073,600 pixels
Auto focus, F 1.8, f 11.9 mm
0.8:1
LED/laser-combined (R, B: LED; G: laser diode)
1.02 – 5.08 m (40 – 200 inches) diagonally, 16:9 aspect ratio
3,000 lm (power mode: normal),1,600 lm (power mode: Eco1),
1,000 lm (power mode: Eco2)
90%
20,000:1 (full on/off)
1,920 × 1,080 pixels (Input signals that exceed this resolution will be
converted to 1,920 × 1,080 pixels.)
fH: 27– 100 kHz, fV: 24 –120 Hz, dot clock: 25–162 MHz
fH: 15– 100 kHz, fV: 24–120 Hz, dot clock: 162 MHz or lower
480i (525i): fH15.75 kHz; fV60 Hz,
576i (625i): fH15.63 kHz; fV50 Hz,
480p (525p): fH31.50 kHz; fV60 Hz,
576p (625p): fH31.25 kHz; fV50 Hz,
720 (750) / 60p: fH45.00 kHz; fV60 Hz,
720 (750) / 50p: fH37.50 kHz; fV50 Hz,
1035 (1125) / 60i: fH33.75 kHz; fV60 Hz,
1080 (1125) / 60i: fH33.75 kHz; fV60 Hz,
1080 (1125) / 50i: fH28.13 kHz; fV50 Hz,
1080 (1125) / 25p: fH28.13 kHz; fV25 Hz,
1080 (1125) / 24p: fH27.00 kHz; fV24 Hz,
1080 (1125) / 24sF: fH27.00 kHz; fV48 Hz,
1080 (1125) / 30p: fH33.75 kHz; fV30 Hz,
1080 (1125) / 60p: fH67.50 kHz; fV60 Hz,
1080 (1125) / 50p: fH56.25 kHz; fV50 Hz
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Vertical: ±10％(manual), horizontal: ±3.4％(manual)
Vertical: ±40°
Ceiling/floor, front/rear
HDMI 19-pin × 1, HDCP compatible, Deep Color compatible
480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1080
(1125)/60i, 1080 (1125)/50i, 1080 (1125)/25p, 1080 (1125)/24p, 1080
(1125)/24sF, 1080 (1125)/30p, 1080 (1125)/60p, 1080 (1125)/50p,
VGA (640 × 480) – WUXGA*4(1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25–162 MHz, audio signal: linear
PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
DVI-I 29-pin × 1
DVI 1.0 compliant, HDCP compatible, for single link only
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA*4(1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25–162 MHz
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD/VD, SYNC: TTL, high impedance, positive/negative automatic
NOTE: HD/SYNC, and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
Specifications
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
DLP™Projectors
3/12
COMPUTER (RGB) IN
R, G, B
Y, P B, PR(Y, CB, CR)
VIDEO IN
AUDIO IN
AUDIO OUT
SERIAL IN
LAN / DIGITAL LINK
3D SYNC OUT
Power cord length
Cabinet materials
Dimensions (W × H × D)
Weight*6
Operation noise*3
Operating temperature
Operating humidity
Wireless remote control unit
Power supply
Operation range*8
Dimensions (W × H × D)
Weight
Supplied accessories
Optional accessories
Digital Interface box
Ceiling mount bracket
Portrait mode mount bracket
D-sub HD 15-pin (female) × 1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD/VD, SYNC: TTL, high impedance, positive/negative automatic
NOTE: HD/SYNC, and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
Pin jack × 1, 1.0 Vp-p, 75 ohms
M3 (L, R) × 1, 0.5 Vrms
M3 (L, R) × 1 (monitor out: 0–1.8 Vrms, variable)
D-sub 9-pin (female) × 1 for external control (RS-232C compliant)
RJ-45 × 1 for network and DIGITAL LINK (video/audio/network/serial
control) connection, 100Base-TX, compatible with PJLink™,
HDCP compatible, Deep Color compatible,
480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1080
(1125)/60i, 1080 (1125)/50i, 1080 (1125)/25p, 1080 (1125)/24p, 1080
(1125)/24sF, 1080 (1125)/30p, 1080 (1125)/60p, 1080 (1125)/50p,
VGA (640 × 480) – WUXGA*4(1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25–162 MHz
Mini DIN 3-pin × 1, for 3D transmitter connection
3.0 m (9 ft 10 in)
Molded plastic
455 × 137*5× 409 mm
(17-29/32 × 5-13/32*5× 16-11/32 inches) (lens included)
Approx. 11.5 kg (24.3 lbs)
35 dB (LIGHT SOURCE MODE: NORMAL),
0 – 45 °C (32 –113 °F)*7
20%– 80% (no condensation)
3 V DC (R6/LR6/AA type battery × 2)
Approx. 15 m (49 ft 3 in) when operated from directly in front of the
signal receptor
48 × 163 × 24.5 mm (1-13/32 × 6-5/8 × 31/32 inches)
Approx. 117 g (4.1 oz) (including batteries)
Power cord with security lock (× 1) (Power cord × 2 for PT-RZ475EA)
Wireless remote control unit (× 1)
Batteries for remote control (R6/LR6/AA type × 2)
Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring
& Control Software) (× 1)
ET-YFB100G
ET-PKR100H (for high ceilings)
ET-PKR100S (for low ceilings)
ET-PKR100P
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
*1 In STANDARD/GRAPHIC picture mode. Measured based on the power consumption rate and a measurement method for the TV receiver.
*2 When the STANDBY MODE is set to ECO, network functions such as power on over the LAN network will not operate. Also, only certain commands
can be received for external control using the serial terminal.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5 With legs at shortest position.
*6 Average value. May differ depending on the actual unit.
*7 0–40 °C (32 –104 °F) between 1,400 m and 2,700 m (4,593 ft and 8,858 ft) above sea level. If the ambient temperature exceeds 35 °C (95 °F), the
light output may be reduced to protect the projector.
*8 Operation range differs depending on environments.
PT-RZ475
As of May 2013
SFD13M007

404.5 (15-15/16)
409 (16-3/32)
455 (17-29/32)
128.5
137
72
(5-1/16)
(5-13/32)
(2-27/32)
Dimensions
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
SPEC FILE
DLP™Projectors
4/12
Terminals
1
6789
23 45
1 LAN / DIGITAL LINK connector
2 HDMI input
3 DVI-I input
4 Computer input
5 Video input
6 Audio input
7 Audio output
8 Serial input
9 3D SYNC output
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
DLP™Projectors
5/12
Standard setting-up position
Caution:
• All construction work should be done by a qualified technician.
• When mounting to the ceiling, use the ceiling mount bracket. Furthermore, in order to prevent it from falling down
from the ceiling, use the supplied wire on the mounting bracket.
Upper edge of projected image
197
(7-3/4)
212
(8-11/32)
*
Lower edge of projected image
Projected image
L
L
L
339–419
(13-11/32 –
16-1/2)
402.5–482.5
(15-27/32–19)
100 (3-15/16)
344
(13-17/32)
100
(3-15/16)
300
(11-13/16)
Projected
image
HH
∅60.5
(∅2-3/8)
unit : mm (inch)
NOTE:
Illustrations show the projector installed
using optional ceiling mount bracket
ET-PKR100H.
This illustration is not drawn to scale.
*Adjustable in 40 mm (1-9/16 in) steps.
unit: meters (feet)
1.02
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
0.67
0.85
1.03
1.21
1.39
1.57
1.75
2.11
2.65
3.55
40
50
60
70
80
90
100
120
150
200
/
/
/
/
/
/
/
/
/
/
(2.2)
(2.8)
(3.4)
(4.0)
(4.6)
(5.2)
(5.7)
(6.9)
(8.7)
(11.7)
(0.7 − 1.0)
(0.8 − 1.2)
(1.0 − 1.5)
(1.1 − 1.7)
(1.3 − 2.0)
(1.5 − 2.2)
(1.6 − 2.5)
(2.0 − 2.9)
(2.5 − 3.7)
(3.3 − 4.9)
0.20 − 0.30
0.25 − 0.37
0.30 − 0.45
0.35 − 0.52
0.40 − 0.60
0.45 − 0.67
0.50 − 0.75
0.60 − 0.90
0.75 − 1.12
1.00 − 1.49
Projection size
[diagonal]
[m] [in]
Projection distance
[L]
Height from the edge of screen
to center of lens [H]
Projection distance for 16:9 aspect ratio screen
unit: meters (feet)
NOTE:
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
DLP™Projectors
6/12
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 16:9
L (m) = (diagonal screen size in inches) × 0.0180 – 0.0476
NOTE:
Distances calculated with the above equations will include a slight error.
H
(Width of
projected image)
V
(Height of
projected image)
Standard postition
of projected image
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
Installable angle
Install the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical
angle of 360°.
• Horizontal direction
The projector may be installed at a horizontal
angle of ±210°.
PT-RZ475
As of May 2013
SFD13M007
0.034H 0.034H
0.10V 0.10V
360°
210°

SPEC FILE
DLP™Projectors
7/12
List of compatible signals
The signals that can be input to this projector are shown in the table below. Horizontal scanning fre-
quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of
162 MHz maximum can be input.
NOTE: The native resolution of this projector is 1,920 × 1,080 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)
Scanning frequency
H
(kHz)
V
(Hz)
Dot clock
frequency
(MHz)
Format
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720 × 483
720 × 576
1,280 × 720
1,920 × 1,035i
1,920 × 1,080i
1,920 × 1,080
1,920 × 1,080i
1,920 × 1,080
640 × 400
640 × 480
800 × 600
832 × 624
1,024 × 768
1,152 × 864
1,152 × 870
1,280 × 720
1,280 × 768
1,280 × 800
1,280 × 960
1,280 × 1,024
1,400 × 1,050
1,440 × 900
1,600 × 1,200
1,680 × 1,050
1,920 × 1,080
1,920 × 1,200
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
33.8
28.1
27.0
27.0
28.1
33.8
67.5
56.3
31.5
37.9
31.5
35.0
37.5
37.9
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
65.5
68.7
80.0
99.0
64.0
67.5
77.1
68.7
37.1
44.8
39.6
47.8
41.3
49.7
60.0
64.0
80.0
91.1
65.2
65.3
82.2
55.9
75.0
65.3
66.6
74.0
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
60.0
50.0
24.0
48.0
25.0
30.0
60.0
50.0
70.1
85.1
59.9
66.7
75.0
72.8
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.0
60.0
70.1
75.0
81.6
85.0
100.0
119.8
70.0
74.9
85.0
75.1
49.8
59.9
49.9
59.9
50.0
59.8
60.0
60.0
75.0
85.0
60.0
60.0
75.0
59.9
60.0
60.0
59.9
60.0
−
−
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
74.3
74.3
74.3
74.3
74.3
148.5
148.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
86.0
94.5
105.0
137.8
94.2
108.0
119.7
100.0
60.5
74.5
65.3
79.5
68.0
83.5
108.0
108.0
135.0
157.5
122.6
121.8
155.9
106.5
162.0
146.3
138.5
154.0
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720 (750)p/60p
720 (750)p/50p
1035 (1125)/60i
1080 (1125)/60i
1080 (1125)/50i
1080 (1125)/24p
1080 (1125)/24sF
1080 (1125)/25p
1080 (1125)/30p
1080 (1125)/60p
1080 (1125)/50p
VGA400
VGA
SVGA
MAC16
XGA
MXGA
MAC21
1280 × 720
1280 × 768
1280 × 800
MSXGA
SXGA
SXGA+
WXGA+
UXGA
WSXGA+
1920 × 1080
WUXGA
VIDEO/S-VIDEO
YPBPR/
COMPUTER (RGB)
HDMI/DVI/
COMPUTER (RGB)/
YPBPR
HDMI/DVI/
COMPUTER (RGB)
*1
*2
*2
1. The “i” appearing after the resolution indicates an interlaced signal.
2. Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
NOTE: Compatible signals for DIGITAL LINK input are the same as compatible signals for HDMI input.
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
DLP™Projectors
8/12
List of compatible 3D signals
The 3D signals that can be input to this projector are shown in the table below.
√
√
–
–
√
–
–
–
–
–
√
(√)
√
√
√
√
(√)
–
–
–
√
√
–
–
√
–
–
–
–
–
(√)
(√)
(√)
(√)
(√)
(√)
(√)
–
–
–
(√)
(√)
–
–
(√)
–
–
–
–
–
–
–
–
–
–
–
–
(√)
(√)
(√)
–
–
–
–
–
–
–
(√)
(√)
(√)
Display mode Display
resolution
(dots)
Scanning
frequency
H
(kHz)
V
(Hz)
Dot clock
frequency
(MHz) Frame
packing
HDMI
Side by
side*1
Top and
bottom
Side by
side*1
DVI-I Computer
Top and
bottom
Frame
sequential
Frame
sequential*2
1280 × 720
1920 × 1080i
1920 × 1080
1920 × 1080
1024 × 768
1280 × 720
45.0
37.5
33.8
28.1
27.0
67.5
56.3
80.0
99.0
92.6
60.0
50.0
60.0
50.0
24.0
60.0
50.0
100.0
119.8
120.0
74.3
148.5
105.0
137.8
161.6
750 (720)p/60p
750 (720)p/50p
1125 (1080)/60i
1125 (1080)/50i
1125 (1080)/24p
1125 (1080)/60p
1125 (1080)/50p
XGA
1280 × 720
*3
*3
*3
*4
*3
*3
*4
*3
*3
*3
*4
*4
*4
*4
*4
*4
*4
*5
*5
*5
*6
*6
*6
*6
*6
*6
*1 Only DVI digital signals are compatible.
*2 DVI digital signals and DVI analog signals are compatible.
*3 A 3D mandatory format for the HDMI standard.
*4 3D images can be displayed by setting the "3D INPUT FORMAT" to "SIDE BY SIDE."
*5 3D images can be displayed by setting the "3D INPUT FORMAT" to "TOP AND BOTTOM."
*6 3D images can be displayed by setting the "3D INPUT FORMAT" to "FRAME SEQUENTIAL."
NOTE: Compatible 3D signals for DIGITAL LINK input are the same as compatible signals for HDMI input.
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Communication conditions (factory setting)
Pin assignments and signal names
6
15
9
D-sub 9-pin (female) Serial input
Description
NC
Send data
Receive data
NC
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
DLP™Projectors
9/12
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
CAUTION
• It may not be possible that responses would delay or commands cannot be executed when commands are sent soon after the
light source is turned on. If this occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before
sending the next command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for com-
mand response to 10 seconds or more.
• When using two or more units, set different IDs for each unit.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte)
Semicolon
(1 byte)
(2 byte)
ID designator
01 to 64: Address number
0A to 0Z: Group ID
ZZ: All units (ID ALL)
ID: 2 characters
(2 bytes) Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
STX ETXC1 P1 P2 ... PnC2A D I1 I2 C3 :;
Cable specifications
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
PC (DTE)Projector
NC
NC
NC
NC
NC
NC
NC
NC
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
DLP™Projectors
10/12
Control commands
Command : Parameter Function Callback
PON
POF
IIS:DL1
IIS:HD1
IIS:DVI
IIS:RG1
IIS:VID
IIS: DL1:HD1
IIS: DL1:HD2
IIS: DL1:PC1
IIS: DL1:PC2
IIS: DL1:VID
IIS: DL1:SVD
OAS
OLP:0
OLP:3
OLP:4
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VPM:DIC
VPM:709
OTE:1
OTE:2
OTE:4
OTE:10
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:0
OOS:1
POWER (STANDBY)
INPUT SELECT
AUTO SETUP
LIGHT SOURCE POWER
PICTURE MODE
COLOR TEMPERATURE
DATE
TIME
On Screen
PON
POF
IIS:DL1
IIS:HD1
IIS:DVI
IIS:RG1
IIS:VID
IIS:DL1:HD1
IIS:DL1:HD2
IIS:DL1:PC1
IIS:DL1:PC2
IIS:DL1:VID
IIS:DL1:SVD
OAS
OLP:0
OLP:3
OLP:4
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VPM:DIC
VPM:709
OTE:1
OTE:2
OTE:4
OTE:10
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:0
OOS:1
On
Off
DIGITAL LINK
HDMI
DVI
COMPUTER
VIDEO
HDMI 1
HDMI 2
COMPUTER 1
COMPUTER 2
VIDEO
S-VIDEO
Normal
Eco 1
Eco 2
Natural
Standard
Dynamic
Cinema
Graphic
DICOM
Rec. 709
Middle
High
User
Default
Date setting
Time setting
On-screen display off
On-screen display on
When DIGITAL LINK input is
selected and input of the
digital interface box
ET-YFB100G is changed
as well.
* When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
DLP™Projectors
11/12
Status request commands
Command:Parameter Function DescriptionCallback
QPW
QIN
QOS
QST
QLP
QPM
QTM:0
QTM:2
QTM:3
QTM:4
QTM:5
QTM:6
QGD
QGT
Standby power status
Input signal status
Input signal status of the digital
interface box ET-YFB100G when
DIGITAL LINK input is selected.
On-screen display status
Projector run time
Light source power mode status
Picture mode status
Temperature status
Date setting status
Time setting status
Off
On
DIGITAL LINK
HDMI
DVI
Computer
VIDEO
HDMI 1
HDMI 2
COMPUTER 1
COMPUTER 2
VIDEO
S-VIDEO
Off
On
00000h–99999h
Normal
Eco 1
Eco 2
Natural
Standard
Dynamic
Cinema
Graphic
DICOM
Rec. 709
Intake
Optical module
Inside
Light source (Red)
Light source (Green)
Light source (Blue)
yyyymmdd (day of week) (*2)
hhmmss
000
001
DL1
HD1
DVI
RG1
VID
DL1:HD1
DL1:HD2
DL1:PC1
DL1:PC2
DL1:VID
DL1:SVD
0
1
p1p2p3p4p5
OLP:0
OLP:3
OLP:4
NAT
STD
DYN
CIN
GRA
DIC
709
p1p2p3p4/p5p6p7p8 (*1)
y1y2y3y4m1m2d1d2w
h1h2m1m2s1s2
*2Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
*1p1p2p3p4: Celsius (°C), p5p6p7p8: Fahrenheit (°F)
Command example
To set the on-screen display off, send the command as shown below.
ADZZ OOS : 0;ETX
ID Address Command
STX
Start Parameter End
NOTE: When sending commands without parameters, a colon (:) is not necessary.
NOTE: If a wrong command is received, the projector will send an ER401 or ER402 command to the computer.
PT-RZ475
As of May 2013
SFD13M007

SPEC FILE
PT-RZ475
DLP™Projectors
As of May 2013
SFD13M007
12/12
Notes on projector placement and operation
Please observe the following precautions for projector placement and operation.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is an unobstructed space of 500 mm (1 foot 8 inches) or more around the projec-
tor’s exhaust openings.
3. Do not stack projector units directly on top of one another for the purpose of multiple (stacked)
projection. When stacking projector units, be sure to provide the amount of space indicated below
between them. These space requirements also apply to installations where only one projector unit
is operating at one time and the other unit is used as a backup.
4. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the pro-
jector so that cool or hot air from other air conditioning equipment does not flow directly toward
the projector’s air intake or exhaust openings.
5. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
6. If the projector is placed in a box, ensure that the projector’s intake and exhaust openings are not
blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into
the intake openings.
7. To install and use the projector via a method that does not use the adjustable feet in a floor stand-
ing installation, fix the projector using the four screw holes for ceiling mounting. (Screw diameter:
M4, tapping depth inside the set: 10 mm, torque: 1.25 ± 0.2 N·m)
500 mm (1 ft 8 in)
or more
500 mm (1 ft 8 in)
or more
500 mm (1 ft 8 in)
or more
Do not stack projector
units directly on top of
one another.
100 mm
(3-15/16 in)
or more
Direction of air intake and exhaust
Intake
Exhaust
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
Product availability differs depending on region and country. This product may be subject to export control regulations.
DLP
HDMI,the HDMI logo and High-Definition Multimedia Interface are trademark of HDMI Licensing LLC in the United States and other countries.
and the DLP logo are trademarks of Texas Instruments.
PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.
All other trademarks are the property of their respective trademark owners.