Panasonic TY-WK15TA2U User manual

TQBA0262-1
Combination LCD TV / DVD Player
and LCD TV
Wall Mount Kit
Installation Manual
Model No. TY-WK15TA2U
Please perform installation work correctly after carefully reading this
installation manual and the operation manual for the Combination LCD
TV / DVD Player and LCD TV.
After installation work is complete, please give this installation manual
to the customer so they can read it and keep for future reference.
(It may be needed for maintenance or when moving.)
Retain all removed parts. They may become necessary when return-
ing to the original installation condition.
Caution:This bracket intended for use only with Panasonic Combina-
tion LCD TV / DVD Player Model TC-11LV1 / TC-15LV1 / TX-15LV1
Series and LCD TV Model TC-20LA1 / TC-17LA1 / TC-14LA1 Series.
Use with other apparatus is capable of resulting in instability causing
possible injury.
Thank you very much for purchasing the wall mount kit for the Panasonic
Combination LCD TV / DVD Player and LCD TV.

2
Safety Precautions
To prevent injury to the user and others and to prevent damage to property, direc-
tions that must be followed are explained as shown below.
Be sure to follow
WARNING
Installation to be performed by
certified personnel only. Be aware of safety factors con- cerning the mounting strength.
Installation
Inadequate installation may
cause the Combination LCD
TV / DVD Player and LCD TV
to fall, resulting in bodily injury.
 Do not install where tolerance is weak.
If the tolerance of the mount-
ing location is weak, the
Combination LCD TV / DVD
Player and LCD TV may fall
resulting in bodily injury.
Prohibited
Prohibited
Insufficient strength may
cause the Combination LCD
TV / DVD Player and LCD TV
to fall, resulting in bodily injury.
Do not hang from the Combina-
tion LCD TV / DVD Player and
LCD TV, place stepsladder, etc.
the Combination LCD TV/
DVD Player and LCDTV may
become damaged or it may
fall, causing bodily injury.
Prohibited
WARNING
The following displays categorize the degree of danger when mishandled.
CAUTION
Possibility of serious injury and even death
when mishandled.
 Directions that must be followed are explained using the following symbols.
(Examples of graphical symbols are shown below.)
This symbol indicates that the direction must be followed with caution.
This symbol indicates that the direction is prohibited.
This symbol indicates that the direction must always be followed.
Possibility of injury or damage to surrounding
property.

3
CAUTION
Installation
Do not install in humid or dusty
areas, or where the Combination
LCD TV / DVD Player and LCD TV
may be exposed to lampblack,
steam or heat.
This may affect the Combi-
nation LCD TV / DVD Player
and LCD TV, and may cause
fire or electric shock.
Do not install with the Combina-
tion LCD TV / DVD Player and
LCD TV facing downward, on its
side, or upside down.
Heat may build up within
the Combination LCD TV
/ DVD Player and LCD TV,
causing fire as a result.
Prohibited
Vent holes are located on
the rear of the Combination
LCD TV / DVD Player and
LCD TV. Blocking these
holes may result in fire.
At least two persons should per-
form installation and removal of
the Combination LCD TV / DVD
Player and LCD TV unit.
Dropping the Combination
LCD TV / DVD Player and
LCD TV may result in injury.
Ensure there is a space of at
least 5 cm between the Combi-
nation LCD TV / DVD Player and
LCD TV body and other objects
at the top, bottom and sides, and
at least 4 cm at the back.
Make sure there is sufficient air cir-
culation so that the ambient tem-
perature does not exceed 35 ° C.
Heat may build up within
the Combination LCDTV/
DVD Player and LCD TV,
causing fire as a result.
Always remove the wall mount-
ing bracket when removing the
Combination LCD TV / DVD Player
and LCD TV.
Injury may result when
accidentally hitting the
projected parts.
•Take caution when removing for
repairs, etc.
Prohibited

4
The wall mount kit is for installing an Combination LCD TV / DVD Player and
LCD TV on a vertical wall for viewing. Do not use it for installing in any other
place than on a vertical wall.
The stand must be removed from the Combination LCD TV / DVD Player and
LCD TV before the wall mount kit may be fitted. Before starting work, be sure
to turn the power off and unplug theAC adapter power supply plug.
Install using techniques that suit the structure and materials of the installation
location.
Use commercially available M4 bolts suitable for the wall material (steel frame,
concrete etc.) as the screws for fastening to the wall.
Allow sufficient strength for safety.
The weight of the Combination LCD TV / DVD Player and LCD TV is approxi-
mately 3.2-5.0 kg.
When mounting on a wall, perform work so that it can withstand the weight of
the television and so that the bracket will not come loose from vibration, etc.
Reinforce the bracket if the mounting section strength is insufficient.
The television may fall if the installation is insufficient or if the screws are loose.
Check to make sure there are no electrical wires eithin the wall.
Use the supplied cable clampers to fix cables. Never fix cables using staples.
Components
Before starting installation, first check that all components have been supplied.
(ø4 ×25 mm)
Precautions for installation work
( 1 )
( 1 ) ( 3 )
( 2 )
( 4 )
(M4 ×12 mm)
Wall mounting bracketA
(main unit side)
Wall mounting bracket B
(wall side)
Angle fixing screw
(for main unit side / wall side fixing) ( 2 )
Bracket mounting screw A
(main unit side) ( 4 )
Bracket mounting screw B (for plywood)
Fall prevention string
Cable clamper

5
To guarantee Combination LCD TV / DVD Player and LCD TV performance
and prevent problems, do not install in locations such as the following:
About the installation location
Be sure to explain the following points to the customer:
The Combination LCD TV / DVD Player and LCD TV is best viewed directly
from the front.
Avoid areas where the florescent lighting reflects on the Combination LCD
TV / DVD Player and LCD TV surface.Although vertical angles can be ad-
justed, the mounting bracket does not move horizontally.
For the main power supply plug, use an outlet that can be easily reached by
hand. Also make sure that the television is at a height such that the power
supply switch can be easily operated, and that it is at a distance within the
remote control range (approximately 6 m from the front).
For the installation height, do not exceed the range of te connection cords
(AC adapter, antenna, etc.).
Be sure to install in a location where theAC adapter is not suspended and
where it can be placed on the floor, table, etc.
Install where there are no objects within 20 cm below the Combination LCD
TV / DVD Player and LCD TV.
Check the installation height, depth, wall structure, etc., before performing
installation work.
Near sprinklers or heat / smoke detectors
Where there is a risk of vibration or impact
Near high voltage wires or motors
Near sources of magnetism, heat, water vapor or soot
Exposed to air from heating equipment
Ensure air can flow around the Combination LCD TV / DVD Player and LCD
TV so that the temperature does not exceed 35 °C .
Otherwise malfunction may occur due to the build-up of heat inside the Com-
bination LCD TV / DVD Player and LCD TV.

6
LCD television
(TC-11LV1)
Bracket mounting
screw A ×4 units
(M4 ×12 mm)
Wall mounting
bracket A
(main unit side)
(Example) When installing for a TC-11LV1
Fall prevention
string ×2 units
Wall mounting
bracket B
(wall side)
Bracket mounting
screw B ×4 units
(ø4 ×25 mm)
Angle fixing
screw ×2 units
(M4 ×12 mm)
Cable clamper ×3 units
Note that the centerline of the television is offset to the right or to the left from
that of the wall mounting bracket. Please exercise care during installation.
Caution
Television center
Bracket center
38.75 mm 2.5 mm
Television center Bracket center
TC-11LV1 TC-15LV1 / TX-15LV1
Sample installation layout

7
Installation procedure
1
Check the strength of the intended installation position
The weight of the Combination LCD TV / DVD Player and LCD TV installed on
the wall mounting bracket is approximately 3.2–5.0 kg.
Referring to the dimension drawing below, check the wall strength at the 4
mounting positions. If strength is insufficient, provide reinforcement.
2Mounting wall mounting bracket B
If bolts or nuts must be embedded in the wall beforehand, such as with a
concrete wall, determine the hole positions by aligning with the actual wall
mounting bracket B, or by referring to the dimension drawing, and embed
anchors of approximately 5 mm diameter.
Use commercially available M4 screws suitable for the mounting surface
material as the screws for fastening to the wall.
Using a level, determine the installation posi-
tion where the fitting is horizontal, and mark
the wall.
Fix wall mounting bracket B (wall side) using
the 4 bracket mounting screws B (plywood).
Note
164
135
55
5454 132
55
Wall mounting holes (x4)
[ Unit: mm ]
Wall mounting bracket B
At least 20 mm

8
3Preparation of wall mounting bracket A
Attach the fall prevention strings (2 units) from the holes on the rear of wall
mounting bracket A (main unit side).
Attach the fall prevention strings
Installation procedure (Cont'd)

9
Before installation, remove the AC adapter and connection cable attached to
the Combination LCD TV / DVD Player.
Fit the television correctly and securely.
For the TC-11LV1
1Remove the television stand
Remove the 4 screws.
Remove the television stand.
2 Fit wall mounting bracket A.
Align the holes in wall mounting bracket A with the screw holes in the
Combination LCD TV / DVD Player. Securely fasten the 4 bracket
attachment screws A (M4 x
12 mm).
4Preparation of television

10
Before installation, remove the AC adapter and connection cable attached to
the Combination LCD TV / DVD Player.
Remove the cable cover (page 8 in the television manual) and the stand cover
(page 9 in the television manual).
Fit the television correctly and securely.
For the TC-15LV1/TX-15LV1
Note:
The cable cover cannot be at-
tached. Store in a safe place in
case you need it in the future.
1Remove the television stand
Remove the 4 screws.
Remove the television stand.
2 Fit wall mounting bracket A.
Align the holes in wall mounting bracket A with the screw holes in the
Combination LCD TV / DVD Player. Securely fasten the 4 bracket
attachment screws A (M4 x
12 mm).
Fit the stand cover.
Installation procedure (Cont'd)

11
For the TC-20LA1
Before starting work, remove theAC adapter and cable connected to the LCD
TV. Perform fitting correctly and securely.
1Remove the stand cover
Remove the one screw.
Lift the lower edge of the stand
cover toward yourself.
Slowly and carefully pull down-
ward to remove.

12
Installation procedure (Cont'd)
Note:
The stand cover is not refitted.
Store in a safe place together
with the attachment screws.
2Remove the TV stand.
Remove the four screws.
Remove the TV stand.
3 Attach the wall hanging bracket A.
Align the holes in the wall hanging bracket A with the screw holes in the
LCD TV. Securely fasten the 4 bracket
fitting screws A (M4 x12 mm).
For the TC-20LA1

13
>PS< 日本製
D2映像
音声
左
右
For the TC-17LA1 / TC-14LA1
Before starting work, remove theAC adapter and cable connected to the LCD
TV. Perform fitting correctly and securely.
1Remove the stand cover
Remove the one screw.
Lift the lower edge of the stand
cover toward yourself.
Slowly and carefully pull down-
ward to remove.
2Remove the TV stand.
Remove the four screws.
Remove the TV stand.

14
Installation procedure (Cont'd)
TBME772
JQA
JQ10009
>PS< 日本製
すぐに電源プラグをコンセントから抜いて、販売店に修理を
ご依頼ください。
取扱説明書の安全上のご注意をお読みのうえ、ご使用ください。
松下電器産業株式会社
DC電圧15  V
定格消費電力  W
松下電器産業株式会社
製造番号
コンポーネント
ビデオ（色差）入力
D2映像
音声 音声
VHF
UHF
DC入力15V
指定のACアダプターを
使用してください。
音声
左
右
音声
左
右
音声
左
右
3Attach the wall hanging bracket A.
4 Refit the stand cover.
Align the holes in the wall hanging bracket A with the screw holes in the
LCD TV.
Securely fasten the 4 bracket
fitting screws A (M4 x12 mm).
Insert the two claws at the up-
per edge of the stand cover.
Press the lower edge of the
stand cover to put into place.
Fasten the screw that was re-
moved in step 1.
For the TC-17LA1 / TC-14LA1

15
5Connection cable routing
Innermost slot
Outermost slot
Tip
Cable clamp
Using the cable clamp.
Cable routing complete
(Example) TC-11LV1
Wrap the clamp around one
cable and pass the tip through
the innermost slot.
Wrap the clamp around the
rest of the cables and pass the
tip through the outermost slot.

16
6
Attaching the Combination LCD TV / DVD Player and
LCD TV to the wall mounting bracket B (wall side)
1Installing on the wall
Be sure to fit the two fall pre-
vention cords to the hangers
on wall mounting bracket B.
Hang the CombinationLCDTV
/ DVD Player and LCD TV on
wall mounting bracket B.
To prevent damage to the wall, make sure that the main unit is
securely mounted on the notches of wall mounting bracket B (wall
side) before letting go of the main unit. Installation of the televi-
sion on the wall should be performed by at least two people.
Caution

17
2Install at the desired angle.
5 ° upsweep
5 ° downsweep
10 ° downsweep
Vertical
Upper notch
Lower notch
Fixing
hole
Upper notch
Lower notch
Fixing
hole
Upper notch
Lower notch
Fixing
hole
Upper notch
Lower notch
Fixing
hole
This Combination LCD TV / DVD
Player and LCD TV wall mount-
ing bracket can be installed in 4
angles : 5°upsweep, vertical, 5°
downsweep and 10°downsweep.
Set the angle by adjusting the
notches of wall mounting bracket
B (wall side) and the concave sec-
tion of wall mounting bracket A
(main unit side) to the desired angle
by referring to the diagrams right.

18
7Wall mounting bracket fastening
To prevent the main unit from fall-
ing, fix the main unit using angle fix-
ing screws (2 units) from both sides
using the fixing holes located on
wall mounting brackets A and B
(main unit side and wall side). If the
fixing holes of the brackets do not
align, installation is insufficient.
Check the installation again and fix
so that screw holes are aligned. e.g. When adjusting the angle to 10°
downsweep.
Fixing hole
Angle fixing screw
(M4 ×12 mm)
Be sure to fit the angle fastening screws on the left and right to prevent the
Combination LCD TV / DVD Player and LCD TV from falling.
Caution

19
LCD television removal
Fixing hole
Angle fixing screw
(M4 ×12 mm)
Remove the angle fastening screws
(x2) fitted to the left and right sides of
the wall mounting bracket.
While lifting the Combination LCD
TV / DVD Player and LCD TV, pull
it away from the wall and remove.
Remove the two fall prevention
cords from the hangers on wall
mounting bracket B.

Wall mounting bracket dimesional drawings
164
135
55
5454 132
55
R2.025
6.05
t =2.0
t =1.2
41.5
39.5
27.2
14.5
32.5
163
129
135.2
Wall mounting bracket A (Main unit side)
Wall mounting bracket B (Wall side)
Vertical/10° downsweep
screw mounting hole
10° downsweep
fixing hole
5° downsweep
fixing hole
5° upsweep fixing hole
Vertical fixing hole
5° downsweep screw
mounting hole
5° upsweep screw
mounting hole
[ Unit: mm ]
MBS0303-0033 (MBS)
C 2003 Matsushita Electric Industrial Co., Ltd. All rights reserved
Printed in Japan