Panasonic WV-CP290 series User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
No model number suffix is shown in this manual.
Lens: Option
Operating Instructions
Color CCTV Camera
Model No. WV-CP290
WV-CP294
ENGLISHFRANÇAIS

2
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended
to alert the user to the presence
of uninsulated "dangerous
voltage" within the product's
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING:
• This apparatus must be earthed.
• Apparatus shall be connected to a mains
socket outlet with a protective earthing
connection.
• The mains plug or an appliance coupler shall
remain readily operable.
• To prevent fire or electric shock hazard, do not
expose this apparatus to rain or moisture.
• The apparatus should not be exposed to
dripping or splashing and that no objects filled
with liquids, such as vases, should be placed
on the apparatus.
• All work related to the installation of this
product should be made by qualified service
personnel or system installers.
• The connections should comply with local
electrical code.
This Class A digital apparatus complies with
Canadian ICES-003.
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area
is likely to cause harmful interference in which
case the user will be required to correct the
interference at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral
devices). Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
The model number and serial number of this product
may be found on the surface of the unit.
You should note the model number and serial
number of this unit in the space provided and retain
this book as a permanent record of your purchase
to aid identification in the event of theft.
Model No.
Serial No.
Power disconnection. Unit with or without ON-OFF
switches have power supplied to the unit whenever
the power cord is inserted into the power source;
however, the unit is operational only when the
ON-OFF switch is in the ON position. Unplug the
power cord to disconnect the main power for all
units.
For Canada
For U.S.A
For U.S.A

3
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
S3125A
ENGLISH

4
Limitation of Liability
THIS PUBLICATION IS PROVIDED "AS
IS" WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE,
OR NON-INFRINGEMENT OF THE THIRD
PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE
TECHNICAL INACCURACIES OR TYPOGRA-
PHICAL ERRORS. CHANGES ARE ADDED
TO THE INFORMATION HEREIN, AT
ANY TIME, FOR THE IMPROVEMENTS
OF THIS PUBLICATION AND/OR THE
CORRESPONDING PRODUCT (S).
Disclaimer of Warranty
IN NO EVENT SHALL Panasonic System
Networks Co., Ltd. BE LIABLE TO ANY
PARTY OR ANY PERSON, EXCEPT FOR
REPLACEMENT OR REASONABLE
MAINTENANCE OF THE PRODUCT, FOR
THE CASES, INCLUDING BUT NOT LIMITED
TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING
WITHOUT LIMITATION, DIRECT OR
INDIRECT, SPECIAL, CONSEQUENTIAL
OR EXEMPLARY, ARISING OUT OF OR
RELATING TO THE PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE
CAUSED BY INAPPROPRIATE USE OR
NEGLIGENT OPERATION OF THE USER;
(3) UNAUTHORIZED DISASSEMBLE,
REPAIR OR MODIFICATION OF THE
PRODUCT BY THE USER;
(4) INCONVENIENCE OR ANY LOSS
ARISING WHEN IMAGES ARE NOT
DISPLAYED, DUE TO ANY REASON OR
CAUSE INCLUDING ANY FAILURE OR
PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL
INCONVENIENCE, OR LOSS OR
DAMAGE, ARISING OUT OF THE
SYSTEM COMBINED BY THE DEVICES
OF THIRD PARTY.
(6) ANY CLAIM OR ACTION FOR DAMAGES,
BROUGHT BY ANY PERSON OR
ORGANIZATION BEING A PHOTOGENIC
SUBJECT, DUE TO VIOLATION OF
PRIVACY WITH THE RESULT OF THAT
SURVEILLANCE-CAMERA'S PICTURE,
INCLUDING SAVED DATA, FOR SOME
REASON, BECOMES PUBLIC OR IS
USED FOR THE PURPOSE OTHER THAN
SURVEILLANCE.

5
Contents
Important safety instructions.......................................................................................................... 3
Limitation of Liability ...................................................................................................................... 4
Disclaimer of Warranty .................................................................................................................. 4
Preface .......................................................................................................................................... 6
Features ........................................................................................................................................ 6
Precautions.................................................................................................................................... 6
Precautions for installation ............................................................................................................ 8
Major operating controls and their functions.................................................................................. 9
Installation and Connection ......................................................................................................... 12
Optional dedicated lens .......................................................................................................... 12
How to use a vari-focal lens.................................................................................................... 16
Troubleshooting........................................................................................................................... 17
Specifications .............................................................................................................................. 19
Standard Accessories.................................................................................................................. 19

6
Preface
The WV-CP290,WV-CP294 are surveillance color CCTV cameras equipped with a 1/3 inch CCD
solid-state image sensor with 752 of horizontal pixels.
Features
The WV-CP290,WV-CP294 are provided with the adaptive black stretch function, high resolution
of 540 TV lines (horizontal), and minimum luminance of 0.8 lx (C/L),0.05 lx (B/W), F1.4(WIDE)
thanks to the adoption of the newly developed digital signal processor.
Precautions
This product has no power switch.
Power is supplied from an external 12 V
DC/ 24 V AC (WV-CP294) or 120 V AC
(WV-CP290) power-supply device. Refer to
service personnel for how to turn on/off the
power.
Use this product for indoor use only.
Do not expose this product to direct sunlight
for hours and do not install the product near
a heater or an air conditioner, otherwise it
may cause deformation, discoloration and
malfunction. Keep this product away from
water.
To keep on using with stable performance
• Parts of this product may deteriorate and
it may shorten the lifetime of this product
when using in locations subject to high
temperatures and high humidity. Do not
expose the product to direct heat such
as from a heater.
• Use this product at temperature within
–10 °C - +50 °C {14 °F - 122 °F} and
humidity below 90 %. (When using this
product without turning the power off)
Do not attempt to disassemble this
product.
To prevent electric shock, do not remove
screws or covers.
There are no user-serviceable parts inside.
Ask qualified service personnel for servicing.
Handle the product with care.
Do not abuse the product. Avoid striking,
shaking, etc. The product could be damaged
by improper handling or storage.
Cleaning the product body
Turn the power off when cleaning the product.
Use a dry cloth to clean the product.
Do not use strong abrasive detergent when
cleaning the product. When the dirt is hard
to remove, use a mild detergent and wipe
gently. Then, wipe off the remaining detergent
with a dry cloth.
Otherwise it may cause discoloration. When
using a chemical cloth for cleaning, read
the caution provided with the chemical cloth
product.
Noise on monitor
This product is equipped with a super
sensitive CCD. Therefore, white dot noise
may appear on the monitor. This phenomenon
is not trouble.
Discoloration on the CCD color filter
When continuously shooting a bright light
source, such as a spotlight, the color filter of
the CCD may have deteriorated and it may
cause discoloration. Even when changing
the fixed shooting direction after continuously
shooting a spotlight for a certain period, the
discoloration may remain.

7
Do not aim the camera at strong light
sources.
A light source such as a spot light causes a
blooming (light bleeding) or a smear (vertical
lines).
Turn the circuit breaker off which supplies
this product with the power when
abnormal conditions are encountered.
Smear Bright subject
Blooming

8
Precautions for installation
This camera is designed to be used
indoors. This camera is not operable
outdoors.
Do not operate this product beyond the
specified temperature, humidity or power
source ratings.
Use this product at temperatures within
–10 °C to +50 °C {14 °F to 122 °F}, and
humidity below 90 %.The input power source
is 12 V DC/24 V AC (WV-CP294) or 120 V AC
(WV-CP290).
Installing place
Contact your dealer for assistance if you
are unsure of an appropriate place in your
particular environment.
• Make sure that the installation area is
strong enough to hold the camera, such
as a concrete ceiling.
• If a ceiling board such as plaster board
is too weak to support the total weight,
the area shall be sufficiently reinforced.
• Do not install this product in a humid or
dust-laden environment.
Otherwise, lifetime of the internal parts
may be shortened.
Avoid installing in the following locations.
• Locations where it may get wet from rain
or water splash
• Locations where a chemical agent is
used such as a swimming pool
• Locations subject to steam and oil
smoke such as a kitchen, Locations near
flammable gas or vapor
• Locations where radiation or X-ray
emissions are produced
• Locations subject to strong magnetic
field or radio waves
• Locations where it may be damaged by
briny air such as seashores
• Locations where the temperature is not
within –10 °C to +50 °C {14 °F to 122 °F}.
• Locations subject to vibrations (This
product is not designed for on-vehicle
use.)
• Locations subject to condensation as the
result of severe changes in temperature
Avoid installing the camera in a place with
a high level of noise.
Installation near an air conditioner, an air
cleaner, a vending machine, or the like
causes noise.
Avoid connections during a lightning
storm.
Otherwise, an electric shock may be caused.
Be sure to remove this product if it is not
in use.
Keep the camera cable away from the
lighting cable.
Failure to observe this may cause noise.
Radio interference
When the camera is used near TV/radio
antenna, strong electric field or magnetic
field (near a motor or a transformer), images
may be distorted and noise sound may be
produced.
Mounting screws
• Screws are not supplied with this
product.
• Prepare them according to the material
and strength of the area where the
product is to be installed.
• Do not use an impact driver. Use of an
impact driver may damage the screws.
• The screws and bolts must be tightened
with an appropriate tightening torque
according to the material and strength of
the installation area.
Power cord (only for WV-CP290)
Connect the power cord securely. Run the
power cord so that no load is applied to the
cord when panning or tilting the camera.
(Failure to observe this may disconnect the
power cord, and accordingly no image is
displayed.)

9
Major operating controls and their functions
Side view(WV-CP290,WV-CP294)
Rear view(WV-CP290) Rear view(WV-CP294)
WV-CP290/CH WV-CP294CH
12
3
5
4
WV CP294CH
24 VIN
~
1- L
12 VINNC
2- N
GND
INT
ATW
ON
ON
B. S.
ON
BLC
D/ N
LL
AW C
OF F
OF F
OF F
VIDEO OUT
9
7
8
120V
INT
ATW
ON
ON
..
ON
BLC
D/N
LL
AWC
OFF
OFFOFF
60Hz
a
VIDEOOUT
BS
9
6
8

10
AFlange-back adjustment ring
This ring adjusts the back-focal distance
or picture focus.
Important:
• When an object is out of focus
because it is too close to the camera,
focus on a darker object with the
aperture open.
BALC lens connector
Supplies power and control signals to an
auto iris lens (option).
CLens (option)
Important:
• The lens mount should be a CS mount
(1"-32UN).
DFlange-back lock screw [LOCK]
Loosen this screw with a screwdriver to
adjust the flange-back adjustment ring.
When completing the adjustment, tighten
this screw.
Recommended tightening torque:
0.05 N·m {0.04 lbf·ft}
Important:
• When the screw is tightened stronger
than the recommended tightening
torque, it may strip the thread or
cause focus misalignment.
ETripod mount base
This socket is used to mount the camera
mount bracket (option). The tripod socket
can be mounted on either top or bottom
of the camera head.(Tripod socket hole:
1/4-20 UNC for tripod)
FPower connector (only for WV-CP290)
The included power cord is connected to
this power connector.
GAC/DC power terminal (only for
WV-CP294)
The power supply of 24 V AC or 12 V DC
is connected to this terminal.
HVideo output connector [VIDEO OUT]
Composite video signals are transmitted.
If this unit is connected to the multiplex
unit, the multiplexed VD2 that is prioritized
over INT/LL is automatically selected.
IDip switch
Selects ON/OFF for white balance mode,
backlight compensation, Adaptive Black
Stretch, day/night mode, and INT/LL for
synchronization mode.
• Day/nightmodeselector[D/N]
ON: Switches from color to black-and-
white images when the ambient
brightness (illuminance) of the
camera is approx. 0.8 lx or less.
OFF: Color picture is displayed normally.
Default setting: ON
Note:
• To obtain color images, a sufficient
level of illuminance(approx.30 lx or
more) is required.
• The switching illuminance level varies
with subjects, light sources, and
lenses.
• The switching illuminances described
above are reference values. The
switching illuminance shall be
decided based on the actual
installation environment.
• AdaptiveBlackStretchSelector[B.S.]
ON: The dark area of the object is
automatically corrected to lighten it.
OFF: Does not compensate.
Default setting: ON
Important:
• In the case of "ON" setting, noise may
be increased in the dark area of the
object.
• In addition, darkness and brightness
may be emphasised in the vicinity of
the boundary between the dark and
bright areas.
INT
AT W
ON
ON
B. S.
ON
BLC
D/ N
LL
AWC
OF F
OFF
OF F

11
• Backlightcompensationselector[BLC]
ON: Compensates the background
automatically if it is brighter than the
object.
OFF: This mode is used when the front of
the object is extremely bright.
Default setting: OFF
Note:
• Under conditions such as extremely
strong backlight, the desired
compensation effect may not be
achieved even with this mode set to
ON to detect the backlight level.
• Whitebalanceselector[ATW/AWC]
ATW: Activates the automatic color
temperature tracking mode. The
camera continuously measures the
color temperature of the light source
and automatically adjusts the white
balance. The adjustment of the color
temperature ranges from approx.
2 700 K to 6 000 K.
AWC: Activates the automatic white
balance control mode. This
adjustment is suitable for a location
where a light source is stable. The
adjustment of the color temperature
ranges from approx. 2 000 K to
10 000 K.
Default setting:ATW
• Synchronizationmodeselector[INT/LL]
Selects the camera synchronization mode
as either internal sync mode (INT) or line-
lock mode (LL).
INT: Sets to internal 2:1 interlace
LL: Sets to line-lock mode
Default setting: INT
Note:
• Please use the INT setting when 12 V
DC is used (WV-CP294).

12
Installation and Connection
1Rotate the lens (option) clockwise slowly to mount the lens.
Important:
• For use of C-mount lens, use the C-mount adaptor (option).
• For prevention of damage to the camera body, use a lens with protrusion of 5.5 mm or less
from the flange surface.
Optional dedicated lens
Protrusion from flange:
5.5 mm or less
Protrusion from mount: ø20 mm or less
Cautions:
• ONLY CONNECT WV-CP294 TO 24 V AC OR 12 V DC CLASS 2 POWER SUPPLY.
• Be sure to connect the grounding lead to the GND terminal (WV-CP290).
Lens type Model No.
ALC lens for 1/3 inch CCD cameras 2x vari-focal WV-LZA61/2S
WV-LZA62/2

13
Pin No.
1 Dump
2 Dump
3 Drive
4 Drive
ALC lens connector
1 3
2 4
Screws (locally
procured) Screws (locally procured)
<Installation sample on a ceiling>
Camera mount
bracket (option)
2Connect the lens cable to the ALC lens connector of the camera.
3Secure the camera mount bracket (option)
to an installation position, and mount the
camera on the camera mount bracket.
Important:
• The camera mount bracket shall be mounted
on the foundation part of the construction or a
part with adequate strength.
• Recommended screw M6, minimum pull-out
strength196 N {44.06 lbf}.
• The other security measures to prevent
dropping also must be considered when the
total weight of camera and its lens is above
1 kg{2.2 lbs.} in addition to the fall protection
measure functioned by coaxial cable,
in order to strengthen the fall protection
countermeasure. (The fall protection measure
can be functioned through the coaxial cable
when the total weight is below 1 kg{2.2 lbs.}.)
Tripod socket
hole:
1/4-20 UNC
for tripod
Tripod mount base
Mounting screws
• When attaching an optional tripod mount
base on the bottom of the camera, use
the removed screws to attach the tripod
mount base. Use of longer or shorter
screws may cause drop or damage.
Recommended tightening torque:
0.39 N·m {0.29 lbf·ft}

14
4The coaxial cable(procured locally) is connected to this video output connector.
Important:
• Be sure to turn off the power of each device before connection.
• Be sure to secure the coaxial cable connectors.
Connect a coaxial cable to the video output connector.
5Use a cable tie (locally procured) to attach the coaxial cable to the camera mount
bracket.
Important:
• The cable tie shall be made of metallic or durable material to be strong enough because
the tie plays the role of camera drop prevention measures in case.
• When the camera mount bracket is mounted on a wall, be sure to observe the mounting
height described on the illustration below.
To video input
Coaxial cables
WV-CP290
120V
INT
ATW
ON
ON
..
ON
BLC
D/N
LL
AWC
OFF
OFF O FF
60Hz
~
VIDEO OUT
BS
Camera mount
bracket (option)
The cable shall be
tied to the camera
mount bracket to
avoid slack.
The cable shall be
tied to the camera
mount bracket to
avoid slack.
Camera mount
bracket (option) More than
270 cm
<Installation sample on a ceiling> <Installation sample on a wall>
Floor
_

15
120V ~ 60 Hz
INT
ATW
ON
ON
..
ON
BLC
D/ N
LL
AWC
OFF
OFF
OFF

VIDEO OUT
BS
Power cord (accessory)
120 V AC,
60 Hz
WV-CP294
Important:
• The power supply of 24 V AC/12 V DC shall
be insulated against 120 V AC.
• The power supply is automatically select-
ed either 24 V AC or 12 V DC. No setting is
required with this camera.
ALoosen the screw of the power cord plug
(accessory).
B Connect the power supply (option) of 24 V
AC or 12 V DC to the power cord plug.
Strip the end of the wire by 3 mm to 7 mm
{1/8" to 1/4"}, and twist the stripped part of
the wire sufficiently to avoid short circuit.
• Specification of cable (wire)
AWG #16 - #28, Single core, twisted
* Check whether the stripped part of the
wire is not exposed and is securely con-
nected.
<Ratings>
24 V AC 12 V DC
A2-N (GND)
B GND NC
C 1-L
CTighten the screw of the power cord plug.
D Connect the power cord plug to the AC/DC
power terminal on the rear side of the cam-
era.
* Make sure that the power cord plug is insert-
ed fully into the AC/DC power supply termi-
nal.
24 VIN
~
1- L
12 VIN
NC
2- N
GND
INT
ATW
ON
ON
B. S.
ON
BLC
D/ N
LL
AW C
OF F
OF F
OF F
VIDEO OUT
To 24 V AC/12 V DC
power supply
C B A
Power cord plug
(accessory)
Stripped
3 mm - 7 mm
{1/8" to 1/4"}
Caution:
• The camera shall be connected with cord set with plug.
Plug for respective country shall be mounted on the
Power cord by a qualified electrical.
6Turn on the power.
WV-CP290
The included power cord is connected to this power connector.
Connect between the power connector on the rear side of the camera and a plug socket
with the supplied power cord.

16
7Adjust the camera angle by loosening the screw of the camera mount bracket while
viewing the video monitor.
Be sure to loosen the screw of the camera mount bracket when the camera angle is adjust-
ed. If the camera angle is changed when the screw is tight, excessive force is applied to
the camera mount bracket and camera, and accordingly they may be damaged. Be sure to
tighten the screw securely after camera angle adjustment.
8Adjust the focus position.
Loosen the flange-back lock screw and rotate the flange-back adjustment ring to adjust the
focus position while monitoring the video monitor. When completing the adjustment, tighten
this screw.
Recommended tightening torque: 0.05 N·m {0.04 lbf·ft}
Important:
• When the screw is tightened stronger than the recommended tightening torque, it may strip
the thread or cause focus misalignment.
Notes:
• When using a fixed-focal lens featuring the focus adjustment, adjust the flange-back length
after setting the lens focus to the FAR end.
• When using a vari-focal lens featuring the focus adjustment, refer to the operating
instructions of the lens in use.
How to use a vari-focal lens
The following are descriptions of how to use a 2x vari-focal lens. Method of adjustment may be
different depending on the lens in use. For further information, refer to the operating instructions
of the lens in use.
A Loosen the zoom lock screw and slide it to the "T" end.
BRotate the focus ring to one step short of the "F" end.
CShoot an object which is located 10 m {33'} away or more, and
adjust the back focal length of the camera.
Important:
• Make sure that it is possible to focus on an object which is
located approx. 1.2 m {4'} away by rotating the focus ring when
the zoom lock screw is at the "W" end.
D Slide the zoom lock screw to an appropriate position and
tighten it.
ERotate the focus ring to bring the camera into focus.
Important:
• When changing the angular field of view, adjust focus by
changing the zoom lock screw position and rotating the focus
ring again.
Zoom lock screw
Focus ring
W
T
N
F
2X TV LENS
3.8~8mm 1:1.4
1
1
2
4
W
T
N
F
2X TV LENS
3.8~8mm 1:1.4
4
5

17
Troubleshooting
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution
in the table or a problem is not described below.
Symptom Cause/solution Reference
pages
No image displayed
• Are the power cord and coaxial cable
connected appropriately?
→Check whether the connection is
appropriately established.
–
• Is the monitor brightness
appropriately adjusted, or is the
contrast appropriately adjusted?
→Check whether the monitor
settings are appropriate.
–
• Is the lens cap detached?
→Check whether the lens cap is
removed.
–
Blurred image
• Is the lens of the camera soiled with
dirt or dust?
→Check whether the lens of the
camera is clean.
–
• Is the focus adjusted correctly?
→Check if the focus is adjusted
correctly.
–
Image Distortion
•Check if the DIP switch is set to “LL”
when the 12 V DC is used.
→Set the DIP switch to “INT”.
9, 11

18
Inspect the power cord, power plug and power connectors periodically.
Symptom Cause/solution Reference
pages
Damaged power cord
sheathing • The power cord, power connector, or
power plug is damaged.
Use of the damaged cord, connector,
or plug may cause electric shock or
fire.
Disconnect the power plug
immediately and request repair to
your dealer.
–
Heated portion of power
line consisting of power
cord, connector, and power
plug during use
The power cord gets hot
when bent or stretched.

19
Specifications
Power source and
power consumption: WV-CP290: 120 V AC 60 Hz, 2.5 W
WV-CP294: 24 V AC 60 Hz, 2.9 W, 12 V DC, 240 mA
Image sensor: 1/3 inch interline transfer CCD
Effective pixels: 768 (H) x 494 (V)
Scanning area: 4.9 mm (H) x 3.7 mm (V)
Scanning system: 2 : 1 interlace
Scanning frequency: Horizontal: 15.734 kHz
Vertical: 60 Hz
Scanning: 525 lines/60 fields/30 frames
Synchronization: Internal (INT), multiplexed vertical drive (VD2) or line-lock (LL)
Resolution: Horizontal: 540 TV lines (at centre)
Vertical: 400 TV lines (at centre)
Minimum illumination: 0.8 lx(C/L),0.05 lx(B/W),F1.4(wide)
Signal-to-noise ratio: 50 dB (equivalent to AGC Off, weight On)
Video output: 1.0 V[P-P] NTSC composite 75 Ω(BNC)
Lens mount: CS-mount
White balance: ATW/AWC
Switch function: White balance mode selector (ATW/AWC), Backlight
compensation selector (ON/OFF), Adaptive Black Stretch
selector (ON/OFF), Day/night mode selector (ON/OFF),
Synchronization mode selector (INT/LL)
Ambient temperature: –10 °C - +50 °C {14 °F - 122 °F}
Ambient humidity: Less than 90 %
Dimensions: 75 (W) x 65 (H) x 137 (D) mm
{2-15/16"(W) x 2-9/16"(H) x 5-3/8"(D)}
(excluding the lens connector)
Weight: WV-CP290: 365 g {0.8 lbs}
WV-CP294: 330 g {0.73 lbs}
Weights and dimensions indicated are approximate.
Operating Instructions (this book)..................1 pc.
CD-ROM*........................................................1 pc.
*The CD-ROM contains the operating instructions (PDF).
The following parts are used during installation procedures.
Power cord (approx.1.8 m)
(only for WV-CP290) .......................................1 pc.
Power cord plug (only for WV-CP294)............1 pc.
Standard Accessories

20