Panasonic WVCS564 - COLOR CCTV CAMERA User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Model No. WV-CS564
Color CCTV Camera
Operating Instructions

2
The serial number of this product may be found on the
top of the unit.
You should note the serial number of this unit in the
space provided and retain this book as a permanent
record of your purchase to aid identification in the event
of theft.
Model No.
Serial No.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOIS
TURE.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is
intended to alert the user to the pres-
ence of uninsulated "dangerous volt-
age" within the product's enclosure that
may be of sufficient magnitude to con-
stitute a risk of electric shock to per-
sons.
The exclamation point within an equilat-
eral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instruc-
tions in the literature accompanying the
appliance.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK), NO
USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ENGLISH VERSION
NOTE: This equipment has been tested and found to com-
ply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harm-
ful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC Caution: To assure continued compliance, (example
- use only shielded interface cables when connecting to
computer or peripheral devices). Any changes or modifica-
tions not expressly approved by the party responsible for
compliance could void the user’s authority to operate this
equipment.
For U.S.A
SA 1965
SA 1966

3
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not use near any heat sources such as radiators, heat registers, stoves or other apparatus (includ-
ing amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta-
cles and the points where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-overs.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not oper-
ate normally, or has been dropped.
S3125A
IMPORTANT SAFETY INSTRUCTIONS

4
• High quality picture of 768 x 494 pixels
• Minimum illumination of 2 lx (at AGC High)
• Protocol adaptability to Panasonic's protocol
• A run of manual operations is memorized in
the patrol learn mode for repetitive use in
future.
• 32 preset positions
FEATURES
Panasonic presents highly advanced CCTV tech-
nology that meets the demands of new and ever-
changing applications.
This high-performance color CCTV camera is uti-
lized as a video surveillance device.
PREFACE
The camera incorporates the Digital Signal
Processor, pan-tilt mechanism, x18 zoom lens
and RS485 communications in a compact enclo-
sure.
• 360° panning at a rotation speed of 300°/s
• Sync selection available from among inter-
nal, line-lock or VD2
• Automatic gain control circuit
• Image hold
• Digital noise reduction effect
PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
■Camera Cleaning . . . . . . . . . . . . . . . . . . 5
■Preset Data Uploading or Downloading . . . 5
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . 5
CONSTRUCTION . . . . . . . . . . . . . . . . . . . . . . 7
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
■Setup Menu . . . . . . . . . . . . . . . . . . . . . . . 8
■Setup Menu Description . . . . . . . . . . . . . 11
SETTING PROCEDURES . . . . . . . . . . . . . . . . 16
■Menu Display . . . . . . . . . . . . . . . . . . . . . 16
■Presetting . . . . . . . . . . . . . . . . . . . . . . . . 17
■Deleting Preset Positions . . . . . . . . . . . . 22
■Home Position Setting (HOME POSITION) . . . 22
■Self Return Setting (SELF RETURN) . . . . 22
■Auto Mode Selection (AUTO MODE) . . . 23
CONTENTS
■Auto Pan Key Setting (AUTO PAN KEY) . . . 25
■Local/Remote Setting (LOCAL/REMOTE) . 25
■Patrol Learn and Patrol Play
(PATROL LEARN and PATROL PLAY) . . 26
■Cleaning (CLEANING) . . . . . . . . . . . . . . 28
■Camera Setting . . . . . . . . . . . . . . . . . . . . 28
■RS485 Setup . . . . . . . . . . . . . . . . . . . . . . 40
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 43
CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . 48
SYSTEM CONNECTIONS . . . . . . . . . . . . . . . 50
PREVENTION OF BLOOMING AND SMEAR . . . . 51
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . 51
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . 52
OPTIONAL ACCESSORIES . . . . . . . . . . . . . . 52
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

5
■Camera Cleaning
Even if this function is used, noise may be produced on the monitor screen, or the preset position may be
deviated in the cause of prolonged use.
In such cases, set the refresh mode on the special menu. (See page 39.)
To use this camera with the WJ-SX550B Matrix Switcher, set the auto cleaning function on each unit side,
then clean WV-CS564 one time a day.
■Preset Data Uploading or Downloading
To download the preset data from the camera to the controller or upload the downloaded data to the
camera, set the following functions to OFF.
Downloading or uploading the data may not work normally if these functions are set to ON.
• Cleaning (See page 28.)
• Auto mode (See page 23.)
• Self return (See page 22.)
Aim the camera at a motionless object such as a wall if possible to download or upload the preset data.
Note: Take notice of the following cases when uploading the downloaded data to the camera.
• Preset positions may vary. If a preset position varies, delete the preset position and set the cor-
rect preset position newly.
• If a preset data of WV-CS564 is uploaded to other models (e.g. WV-CS854 series), an error may
occur and uploading may not be completed successfully.
1. Do not attempt to disassemble the cam-
era.
To prevent electric shock, do not remove
screws or covers.
There are no user-serviceable parts inside.
Ask a qualified service personnel for servic-
ing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be dam-
aged by improper handling or storage.
3. Do not expose the camera to rain or mois-
ture, nor try to operate it in wet areas.
This product is designed for indoor use or
locations where it is protected from rain and
moisture. Moisture can damage the camera
and also cause electric shock.
If the camera becomes wet, turn the power
off immediately and ask a qualified service
personnel for servicing.
PRECAUTIONS

6
4. Do not use strong or abrasive detergents
when cleaning the camera body.
Use a dry cloth to clean the camera when it
is dirty.
When the dirt is hard to remove, use a mild
detergent and wipe gently. Care should be
taken not to scratch the dome cover when
wiping it.
Afterwards, wipe off the remained part of the
detergent in it with a dry cloth.
5. Never face the camera towards the sun.
Whether the camera is in use or not, never
aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may
be caused.
6. Never face the camera at a place exposed
to light sources for a long time.
If light sources such as spot light cause
burn-in on the display screen, part of image
may discolor due to deterioration of color fil-
ter in CCD when changing aim of the cam-
era etc.
7. Do not install this camera upside down.
This camera is designed for mounting on the
ceiling or wall. Using this camera installed
upside down, for example, mounted on the
floor, may cause malfunction.
8. If “OVER HEAT” sign appears on the mon-
itor screen.
The temperature inside the camera exceeds
the normal level because of a malfunction of
the cooling fan etc. If it happens, turn the
power off immediately and refer servicing to
qualified service personnel.
9. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Do not use the camera in an extreme envi-
ronment where high temperature or high
humidity exists. Do not place the camera
near heat sources such as radiators, stoves
or other units that produce heat.
Use the camera under conditions where
temperatures are between –10°C and +50˚C
(14˚F - 122°F) [Recommended temperature:
+40˚C (104˚F)], and humidity is below 90%.
The input power source is 24 V AC.
10. Do not install the camera near the air out-
let of an air conditioner.
The lens may become cloudy due to con-
densation if the camera is used under the
following conditions.
• Rapid temperature fluctuations by
switching the air conditioner on and off.
• Rapid temperature fluctuations due to
frequent door opening and closing.
• Use in an environment where eyeglass-
es become foggy.
• Use in a room filled with cigarette smoke
or dust.
If the lens becomes cloudy due to conden-
sation, remove the dome cover and wipe
all moist surfaces with a soft cloth.
11. Consumables
Parts having contacts such as the lens-drive
motors, cooling fan motor and slip-rings
inside the camera are subject to wear with
time. About replacement and maintenance
of such parts, please ask the nearest service
center.
12. Do not aim the camera at the same object
for a long time.
Burn-in of an image may be caused on the
fluorescent screen of CRT.
• Matsushita Electric Industrial Co., Ltd. here-
with declares that it will not be liable for any
damage, whether direct or indirect, caused
by using for business transaction or security,
or malfunctioning of this product.

7
yCamera Mounting Base
uPanning Starting Point
iFall Prevention Wire
oDecoration Cover
!0 Dome Cover
qNot Used
wNot Used
eVideo Output Connector
rData Port
tPower Cable
CONSTRUCTION
w
e
r
t
q
yu
o
i
!0

98
SETUP
Setup
Menu
Home
Position
Selection
Self
Return
Setting
Auto Pan
Key
Setting
Local/
Remote
Selection
Shutter
Speed
Selection
WHITE
BAL
AWC ATW
BLC
OFF
Light
Control
ALC/MANUAL
BLC
ON
Manual
Level
Adjustment
(Contrast)
Manual
Mask
Area
Selection
INT
Manual
Selection
VD2
Automatic
Selection
Manual
Level
Adjustment
Manual
Level
Adjustment
V-phase
Manual
Adjustment
LL
Manual
Selection
PRESET
Menu
Camera
Menu
CAMERA ID
Editing
CAMERA ID
Display
Position
Auto Pan
Setting
Menu Image Hold
ON/OFF
Cleaning
Display
Cleaning
ON/OFF
Learning
Display
Patrol Learn
Play/Stop
Sync
INT/LL
Auto
Mode
Selection
Position
Setting Light
Control
ALC/MANUAL
Dwell Time
Setting
MAP
Menu
Preset
No. SET
Menu
Preset
ID
Setting
Preset
ID
Editing
Scene File
Setting
Manual
Iris
Adjustment
BLC
ON
BLC
OFF
Manual
Mask
Area
Selection
Manual
Level
Adjustment
White
Balance
AWC ATW
Shutter
Speed
ON/OFF
AGC Mode
Selection
LOW/MID/
HIGH/OFF
AF Mode
Selection
Preset
Setting
Menu
Manual
Level
Adjustment
Manual
Level
Adjustment
Camera
Reset
Pedestal
Adjustment
AP
Gain
Adjustment
Chroma
Gain
Adjustment
Stop
Bit
Selection
Parity
Check
Selection
Data
Bit
Selection
BAUD
Rate
Selection
Sub-
Address Delay Time
Selection
Xon/Xoff
Selection
Wait
Time
Selection
RS-485
Setup
Unit
Number
Selection
RS-485
Setup
To A
A
Special
Refresh
To
B
AF MODE
Selection
B
AGC Mode
Selection
LOW/MID/
HIGH/OFF
HUE
Adjustment
EL-ZOOM
ON/OFF
■Setup Menu
Setup menus are shown in the diagram below. Various kinds of setup are available to have the camera
fulfill your requirements. Menus are built in a hierarchical structure from the Setup menu at the top to
Manual Mask Area Selection at the bottom.
These menus are described in the following pages for reference prior to setup.
Switches, keys and the joystick are used for setup operations.

10
Open special F2 key
The keys (switches) to use for setup are shown in the table below. The joystick on the connected con-
troller may also be used for setup. The table also shows the functions versus the operations of the individ-
ual controllers. For details, see the manual for the controller to be used. The switches and controls are
abbreviated as SW and CTRL respectively in the table.
OPERATE LOGIN ALARM
FUNCTION
SX
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELE
FOCUS
ZOOM
AUTOFOCUS
IRIS RESET
HOME
SET UP
ALM RECALL
CAM SETUP CAM FUNCTION
MULTISCREEN
DEF
WIPER
EL-ZOOM
SHIFT
ALM RESET
VTR CAM
STILL
-1 CAM/DEC
ALM SUSPEND
+1 CAM/INC
PATR OLSTOP
AUX 1
AUX 2
B/W UNIT
SEQ PAUSE
BOOST
SEQUENCE AUTO
PRESET
POSI
FS
MON CAM
LOGOUT
ESC SET
CAMERA SITE CONTROL
UP
LR
DOWN
BUSY PROHIBITED
MONITOR
UNIT CAMERA
System Controller WV - CU
360
1 2 3
4 5 6
7 8 9
MON CAM
ESC SET
0
ACK
RESET BACK SEQ FORWARD SEQ ALT
DEC
–1CAM INC +1CAM STOP
12
AUX
CLOSE OPEN
IRIS
PRESET
FOCUS
NEAR
ZOOM
TELE
FARWIDE
System Controller WV-CU 550550B
LEFT RIGHT
UP
DOWN
ALARM BUSY
F3 F4F2F1
AF
[WV-CU550B]
[WV-CU161]
[WV-RM70]
Joystick
CAM (SET)
Key
MON (ESC)
Key
CAM (SET)
Key
MON (ESC)
Key
SET Key
CAM (SET) Key
OPERATE REMOTE
NORMAL PROG ALARM
RESET
SYSTEM
ALARM OFF
Camera Controller WV-RM 7070
Up Switch
Set Switch Right
Switch
Left Switch Down
Switch
[WV-CU360] Joystick
Joystick
FOCUS Switch
ZOOM Switch
FOCUS Switch
ZOOM Switch
Up Switch
R
System Controller WV-CU
1 2 3
4 6
7 8 9
0
5
SHIFT
OPERATE ALARM
RESET
RESET
SUSPEND
CAMERA
SETUP
PATROL
PAY
PROGRAM
PRESET
CAMERA
FUNCTION
SERUP
ESC
HOME
SET
PRESET WIDE TELE
NEAR
AUX1
B/W
AUTO
WIPER
AUX2
DEF
UP
DOWN
L
FAR
FOCUS
IRIS
CLOSS OPEN
PROGRAM
ALARM
IRIS RESET
AUTOFOCUS
Left Switch
Right Switch
Down Switch
Function/Controller WV-CU550B WV-CU360 WV-CU161 WV-RM70
Open CAM SETUP See page 16 CAM SETUP key (for 2 sec-
onds or more)
CAMERA SETUP
key (for 2 seco-
nds or more) See page 16
Close CAM SETUP F4 key CAM SETUP key (for 2 sec-
onds or more)
CAMERA SETUP
key (for 2 seco-
nds or more) PROG SW
Move the cursor Joystick
(←, ↑, ↓, →)Joystick (←, ↑, ↓, →)Direction SW (←, ↑, ↓, →)Direction SW (←, ↑, ↓, →)
Select a parameter Joystick
(←, →)Joystick (←, →)Direction SW (←, →)Direction SW (←, →)
Adjust the level Joystick
(←, →)Joystick (←, →)Direction SW (←, →)Direction SW (←, →)
Move the camera
direction Joystick
(←, ↑, ↓, →)Joystick (←, ↑, ↓, →)Joystick (←, ↑, ↓, →)Direction SW (←, ↑, ↓, →)
Zoom & Focus ZOOM CTRL &
FOCUS CTRL ZOOM CTRL & FOCUS CTRL ZOOM CTRL & FOCUS CTRL Direction SW
(←, ↑, ↓, →)
Enter the setting CAM (SET) key CAM (SET) key CAM (SET) key SET SW
Open a submenu CAM (SET) key CAM (SET) key CAM (SET) key SET SW
Enter CAM ID &
PRESET ID
display position MON (ESC) key MON (ESC) key MON (ESC) key SET SW
(for 2 seconds
or more)
Enter MASK
setting MON (ESC) key MON (ESC) key MON (ESC) key SET SW
(for 2 seconds
or more)
All Reset F3 key 4+5+6 key (for 2 seconds
or more)
4+5+6 key
(for 2 seconds
or more)
R+SET+L SW
(for 2 seconds
or more)
4+6 key
(for 2 seconds
or more)
4+6 key
(for 2 seconds
or more)
R+L SW
(for 2 seconds
or more)
Notes:
• A changed parameter is entered only when you move the cursor to
another item or open a new menu.
A changed parameter will not be entered if the setup menu is closed
without taking either of the above steps.
• Setting procedures in the following pages are described on the assump-
tion that the camera is used with WJ-SX550B Matrix Switcher and WV-
CU550B System Controller.

11
■Setup Menu Description
●Presetting
(1) Position (POSITION SET)
Aligns the camera position and focal point by panning, tilting, zooming and focusing.
See page 17 for the setting.
(2) Preset Identification (PRESET ID)
Assigns the name for preset IDs (identification of up to 16 alphanumeric characters) and can be
switched on or off on the monitor screen.
See page 19 for the setting.
(3) Light Control (ALC/MANUAL)
Selects the ALC or MANUAL mode for adjust the lens iris.
See page 20 for the setting.
(4) Dwell Time (DWELL TIME)
Displays the picture of each camera position in the selected duration.
You can select a preset duration from the menu.
See page 21 for the setting.
(5) Scene File (SCENE FILE)
Stores up to 10 files.
Each file has a set of detailed parameters for the shutter speed, AGC, white balance, and AF mode.
The scene files can be recalled later to reproduce the parameter settings under the same conditions
as stored in the files.
See page 21 for the setting.
● Home Position (HOME POSITION)
A home position is the camera’s basic position.
It returns to this position automatically when a specific time has elapsed after a manual operation. This
setting functions only when AUTO MODE is OFF.
See page 22 for the setting.
●Self Return (SELF RETURN)
Self-return is the time-out parameter for returning to the home position.
The camera returns to AUTO MODE if it is set to ON when a specific time has elapsed after a manual
operation.
See page 22 for the setting.
●Auto Mode (AUTO MODE)
The auto mode is used for setting the movement of the camera.
You can select one from four automatic operation modes and one manual operation mode as follows:
OFF: No automatic operation. The camera can be operated only manually.
SEQ: The camera operates in the sequence of preset positions in numerical order.
SORT: The camera operates in the sequence of preset positions counterclockwise from Pan
Starting Point.
AUTO PAN: The camera automatically turns within the preset panning range.
PATROL: The camera operates in the patrol learn function.
See page 23 for the setting.

12
●Auto Pan Key (AUTO PAN KEY)
This setting assigns the SEQ, SORT, AUTO PAN or PATROL (PLAY) mode to the AUTO key on the con-
troller.
After setting this, the AUTO key performs as assigned.
Note: The AUTO PAN LED on the controller does not light if the mode other than the AUTO PAN mode is
assigned.
●Local/Remote (LOCAL/REMOTE)
This setting determines whether the camera continues or stops the ongoing auto operation when the con-
troller is turned off.
LOCAL: The camera continues operating in the auto mode when the controller is turned off.
REMOTE: The camera stops operating in the auto mode approx. 1 minute after the controller is turned
off.
See page 25 for the setting.
●Patrol Learn and Patrol Play (PATROL)
A set of manual operations is stored (LEARN), reproduced (PLAY) or turned inactive (OFF). Patrol
operation stops if SEQ, SORT or AUTO PAN is set to AUTO MODE on the SETUP menu. See page 26
for details.

13
●Cleaning (CLEANING)
This is used for refreshing the electric-mechanical contacts built in the camera. Use this function for
maintenance when the camera has been directed to a specific spot or panned over a specific range
for a long time.
●Image Hold (IMAGE HOLD)
The camera picture remains a still image on the monitor screen or until the camera reaches the pre-
set position. This function is useful for surveillance via a local area network.
●Camera
(1) Camera Identification (CAMERA ID)
You can use the camera identification to assign a name to the camera. The camera ID consists of up
to 16 alphanumeric characters. You can select whether to have the camera ID displayed on the moni-
tor screen or not. See page 28 for the setting.
(2) Light Control (ALC/MANUAL)
You can select the mode for adjusting the lens iris. There are two modes as follows:
ALC: The lens iris is automatically adjusted according to the brightness of the object.
You can select one of two modes (BLC ON or BLC OFF) of backlight compensation.
Backlight compensation is available for the ALC mode. It eliminates strong background light
which makes the camera picture dark such as a spotlight.
MANUAL: The lens iris is fixed at the value that you have set regardless of the brightness of the
object.
• ALC Mode with BLC ON
An important object in a scene is usually placed in the center of the monitor screen. By the setup,
more photometric weight is given to the center of the screen than to the edge of the screen (where
bright backlight would most likely be located). In such a case, the object at the center of the screen
can be still clearly seen even though the backlight may vary.
See page 30 for the setting.
• ALC Mode with BLC OFF
This mode is effective when a main object in the scene is not located in the center of the screen but a
source of bright light is located near the center of the scene. In this mode, the picture is divided into
48 areas that mask the light to keep the clarity of the picture.

14
Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lens
iris control in ALC mode.
(3) Shutter Speed (SHUTTER)
You can select a shutter speed of 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, and
1/10 000 seconds.
See page 32 for the setting.
(4) Gain Control (AGC)
You can set the gain (brightness level portion of an image) to automatic adjustment [Automatic Gain
Control ON (LOW, MID, HIGH)] or fixed (Automatic Gain Control OFF).
See page 32 for the setting.
(5) Synchronization (SYNC)
You can select the internal sync (INT) mode or the line-lock sync (LL) mode. Additionally, this model
accepts the VD2 signal (multiplexed vertical drive signal with the composite video output signal) from
a specified component. Whenever the VD2 signal is supplied to this camera, the camera automatical-
ly switches to the VD2 sync mode.
When you select the line-lock sync (LL) mode, you can set vertical phase adjustment.
See page 33 for the setting.
Important Notices:
The priority of sync modes is given as follows:
1. Multiplexed vertical drive (VD2) (highest)
2. Line-lock (LL)
3. Internal sync (INT) (lowest)
Note: The priority of the automatic sync mode is the same as shown above.

15
(6) White Balance (WHITE BAL)
You can select one of two modes for white balance adjustment as follows:
• Auto-Tracing White Balance (ATW)
In this mode, the color temperature is monitored continuously and thereby white balance is set auto-
matically. The color temperature range for the proper white balance is approx.2 600 - 6 000 K. Proper
white balance may not be obtained under the following conditions:
1. The color temperature is out of the 2 600 - 6 000 K range.
2. When the scene contains mostly high color temperature (bluish) objects, such as a blue sky.
3. When the scene is dim.
In these cases, select the AWC mode.
• Automatic White Balance (AWC)
In this mode, accurate white balance is obtained within a color temperature range of approx. 2 300 -
10 000 K.
See page 34 for the setting.
(7) Auto Focus (AF MODE)
The camera adjusts the focus automatically by sensing sharpness in the center of the picture. S, M
and L stand for the breadth of the sensing area: Small, Middle and Large.
See page 36 for details.
MANUAL S, M, L: Auto-focus is activated when the AF key on the controller is pressed.
AUTO S, M, L: Auto-focus is activated automatically while operating manually: pan, tilt or zoom.
(8) Electronic Zoom (EL-ZOOM)
Up to 2-fold electronic zooming is available besides 18-fold optical zooming.
(9) Image Hold (IMAGE HOLD)
The camera picture remains a still image on the monitor screen until the camera reaches the preset
position. This function is useful for surveillance via a local area network.
(10)Special Menu (SPECIAL)
This menu allows you to adjust and set up the following items and functions: chroma level, aperture
level, pedestal level, hue adjustment and refresh function.
You can also reset your parameters to the values preset at the factory.
See page 38 for the setting.
●RS485 communication
Camera communication parameters
See the following items pages for the setting.
• Full/Half duplex (page 46)
• Transmission Speed (2 400 - 19 200 bps) (page 40)
• Parity bit, Stop bit, Flow control (pages 40 and 41)
• Wait time, Delay time (page 41)
• Camera units (96 units max.) (page 44)
• Termination ON/OFF (page 46)
• Reset parameters (page 43)

16
SETTING PROCEDURES
The following setting procedures are described on the assumption that this model is used in combination
with the WJ-SX550B Matrix Switcher and WV-CU550B System Controller. In case of using a controller
other than the WV-CU550B, refer to the table on page 10.
■Menu Display
●Setup Menu Display
WV-CU550B
1. Select the camera number you want to set up and a monitor to
display the SET UP MENU.
2. Display the D4 menu on the LCD by pressing the appropriate cur-
sor buttons.
3. Press the F1 button.
The SET UP MENU appears on the monitor screen.
4. To close the SET UP MENU, press the F4 button.
WV-CU360
Press the CAM SETUP key for 2 seconds or more to open the
SETUP menu.
WV-CU161
Press the CAMERA SETUP key for 2 seconds or more to open the
SETUP menu.
WV-RM70
1. Turn the MODE SELECTION switch to NORMAL or ALARM OFF.
2. Press the PROG switch for 2 seconds or more to open the
Program Menu.
3. Move the cursor to Camera Set Up Menu, and press the SET
switch to open the SETUP MENU.
●Submenu Display
The items marked can be selected/changed on the submenu.
• Move the cursor to an item with the mark and press the CAM
(SET) key. The submenu appears.
D4 menu
F1
F1 F2 F3 F4
Camera Set Up Menu
Res A.Res Exit
F2 F3 F4
Camera Set Up Menu
On Exit
** RS485 SET UP **
UNIT NUMBER
SUB ADDRESS
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET
1
-----
19200
8
NONE
1
NOT USE
OFF
---
---
Submenu
(for RS485 setup)
** SET UP MENU **
PRESET 1
MAP
HOME POSITION
SELF RETURN
AUTO MODE
AUTO PAN KEY
LOCAL/REMOTE
PATROL
CLEANING
CAMERA
RS485 SET UP
OFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu

17
■Presetting
●Preset Menu Display
1. Displaying the preset menu directly
(1) Move the cursor to PRESET 1 and move the joystick to the
right or left to select the position number to be set.
(2) Press the CAM (SET) key.
The preset setting menu appears on the monitor screen.
2. Displaying the preset menu from the PRESET NUMBER SET menu
(1) Move the cursor to MAP and press the CAM (SET) key.
The PRESET NUMBER SET menu appears on the monitor
screen.
(2) Move the cursor to the position number to be set and press
the CAM (SET) key.
Notes:
• The * mark means that the position number has been preset.
• The character H means the home position.
• On the second bottom line, the preset ID appears respective
to the selected number. “DOOR” next to “ID” is for preset
position number 1 in the example shown right.
●Position Setting (POSITION SET)
1. Move the cursor to POSITION SET on the preset setting menu and
press the CAM (SET) key.
The position setting menu appears.
2. To Set Panning/Tilting Positions
(1) Move the cursor to PUSH SET for PAN/TILT and press the
CAM (SET) key. The PAN/TILT setting menu appears.
(2) Select panning/tilting positions by moving the joystick up and
down, right and left, and press the CAM (SET) key.
The positions are set and the screen returns to the position
setting menu.
** SET UP MENU **
PRESET 1
MAP
HOME POSITION
SELF RETURN
AUTO MODE
AUTO PAN KEY
LOCAL/REMOTE
PATROL
CLEANING
CAMERA
RS485 SET UP
OFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
** PRESET NUMBER SET **
2
6
10
14
18
22
26
30
1
5
9
13
17
21
25
29
ID:DOOR
RET
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
PRESET NUMBER SET menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET DEL
ON
ALC
10S
OFF
••••••••|
L H
Preset setting menu
→ PUSH SET
→ PUSH SET
** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←− 0.0 →
RET
FLOOR1
DOOR
Position setting menu
→ PUSH SET
→ PUSH SET
** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
U TILT D/L PAN R
PAN OFFSET SET ←− 0.0 →
RET
FLOOR1
DOOR
** SET UP MENU **
PRESET 1*
MAP
HOME POSITION
SELF RETURN
AUTO MODE
AUTO PAN KEY
LOCAL/REMOTE
PATROL
CLEANING
CAMERA
RS485 SET UP
OFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
PAN/TILT setting menu

18
3. Pan Offset
If the camera is replaced with a new one, the pan offset function
is used to adjust its positions to be the same as before except
patrol setting.
The controller can be downloaded or uploaded the preset posi-
tion data.
Caution: The preset data for other camera models (WV-CS650 for
example) is incompatible with WV-CS564's. WV-CS564's pre-
set data will be destroyed if you upload the conventional
data. If this happened, reset the WV-CS564 to the default set-
tings. Download the factory settings into the controller and
upload the correct preset data newly to the initialized WV-
CS564.
(1) Display the PRESET NUMBER SET menu.
(2) Select a position number for the picture to be most enlarged
among the numbers by using the joystick. Then press the
CAM (SET) key. The position setting menu appears.
(3) Move the cursor to PAN OFFSET SET and select the right or
left arrow by moving the joystick.
(4) Press the CAM (SET) key until the desired offset value
appears.
(5) Move the cursor to other than PAN OFFSET SET, and press
the MON (ESC) key.
Notes:
• Further adjustment of the other positions is unnecessary. This
adjustment applies to all other positions.
• Make sure to move the cursor before pressing the key in step
5. Otherwise the settings will be ignored.
• Retry when the camera fails to upload or download the data.
4. To Set the Lens Zoom and Focus Positions
(1) Move the cursor to PUSH SET for ZOOM/FOCUS and press
the CAM (SET) key. The ZOOM/FOCUS setting menu
appears.
(2) Select a zoom position by moving the zoom control up and
down, and a focus position by moving the focus control up
and down, and then press the CAM (SET) key.
The positions are set and the screen returns to the position
setting menu.
Notes:
• When the camera is used at a nearly horizontal angle, the
focus may not be adjustable to a high level of accuracy.
• If you move the cursor to the position number and move
the joystick right or left, the position number can be
selected.
The selected preset position number can also be set after
pressing the CAM (SET) key.
• The preset and camera IDs appear at the lower-left cor-
ner of the position setting menu after setting them.
5. Move the cursor to RET and press the CAM (SET) key to return to
the preset setting menu.
→ PUSH SET
→ PUSH SET
** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←− 0.0 →
RET
FLOOR1
DOOR
Position setting menu
** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
U ZOOM D/L FOCUS R
PAN OFFSET SET ←− 0.0 →
RET
FLOOR1
DOOR
→ PUSH SET
→ PUSH SET
→ PUSH SET
→ PUSH SET
** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←− 0.0 →
RET
FLOOR1
DOOR
Position setting menu
** PRESET NUMBER SET **
2
6
10
14
18
22
26
30
1
5
9
13
17
21
25
29
ID:DOOR
RET
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
PRESET NUMBER SET menu
→ PUSH SET
→ PUSH SET
** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←− 0.0 →
RET
FLOOR1
DOOR
Position setting menu
ZOOM/FOCUS setting menu

19
●Preset Identification Setting (PRESET ID)
1. Move the cursor to PRESET ID on the preset setting menu and
select ON or OFF by moving the joystick to the right or left.
The factory default setting is OFF.
ON: Preset ID appears on the monitor screen.
OFF: Preset ID does not appear.
2. Press the CAM (SET) key to display the preset ID setting menu.
To Enter a New Preset ID
(1) Move the cursor to the desired character using the joystick,
and press the CAM (SET) key.
(2) The selected character appears in the editing area. (The
pointer in the editing area moves to the right automati-
cally at this moment.) To enter a blank, select SPACE.
(3) Repeat the above procedure until all characters are
entered.
To Copy a Preset ID from Another Position
(1) Move the cursor to COPY and press the CAM (SET) key. The
preset ID in the preceding position is immediately shown.
Each consecutive pressing of the CAM (SET) key displays the
ID preceding the one currently displayed.
(2) Display the most prospective ID.
(3) Follow the step “To Change an Entered Preset ID” if neces-
sary.
To Change an Entered Preset ID
(1) Move the pointer to the character to be edited in the editing
area by using the joystick.
(2) Select a new character by using the joystick.
(3) Press the CAM (SET) key to determine the Preset ID.
To Delete an Entered Preset ID
Move the cursor to RESET and press the CAM (SET) key.
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET DEL
ON
ALC
10S
OFF
••••••••|
L H
Preset setting menu
Command
Editing
Area
Character
Area
Pointer
Character Cursor
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
SPACE
COPY POSI RET RESET
DOOR............
Preset ID setting menu
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
SPACE
COPY POSI RET RESET
DOOR............
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
SPACE
COPY POSI RET RESET
DOOR............
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
SPACE
COPY POSI RET RESET
DOOR............

20
To Set a Display Position for a Preset ID
(1) Move the cursor to POSI and press the CAM (SET) key. The
display position set menu appears.
(2) Using the joystick, move the ID to the desired position on the
monitor screen, and press the MON (ESC) key. The display
position is set and the monitor screen returns to the preset ID
setting menu.
To Enter the Next ID without Returning to the Preset Setting
Menu
(1) In the preset ID setting menu, move the cursor to the top line
and select the desired position number by moving the joy-
stick to the right or left.
(2) Enter, copy, change or delete the ID as described above.
To Return to the Preset Setting Menu
Move the cursor to RET and press the CAM (SET) key.
●Light Control Setting (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL and select ALC or MANUAL by
moving the joystick to the right or left.
The factory default setting is ALC.
ALC: The lens iris is automatically adjusted to suit the brightness
of the object.
MANUAL: The lens iris is fixed at the set value regardless of the
brightness of the object.
2. In case of ALC
Press the CAM (SET) key. The backlight compensation menu
appears on the monitor screen. See page 30 for the setting.
3. In case of MANUAL
Press the CAM (SET) key. The setting menu appears on the moni-
tor screen. Set the lens iris level as desired by moving the joystick
to the right or left.
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
SPACE
COPY POSI RET RESET
DOOR............
FLOOR 1
DOOR
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
SPACE
COPY POSI RET RESET
DOOR............
Display position set menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET DEL
ON
ALC
10S
OFF
••••••••|
L H
Preset setting menu
** MANUAL CONT **
IRIS
RET
••••|••••
CLOSE OPEN
Manual setting menu

21
●Dwell Time (DWELL TIME)
• Move the cursor to DWELL TIME and set a dwell time by moving
the joystick to the right or left. The factory default setting is 10S.
Dwell time changes as follows:
S stands for second(s), and MIN stands for minute(s).
●Scene File Setting (SCENE FILE)
1. To set a scene file number
Move the cursor to SCENE FILE and select a scene file number (1
to 10, or OFF) by moving the joystick to the right or left. The facto-
ry default setting is OFF. No scene file is selected at OFF.
2. To set scene file details
Move the cursor to a scene file number and press the CAM (SET)
key. The setting menu appears.
See the pages below for the setting.
Shutter speed: page 32
AGC: page 32
White balance: page 34
Auto focus: page 36
●Preset Speed Setting (PRESET SPEED)
• Move the cursor to PRESET SPEED and select a speed by moving
the joystick to the right or left.
●To Return to the Preset Number Set Menu
• Move the cursor to RET and press the CAM (SET) key. The PRE-
SET NUMBER SET menu appears with the * mark on the right of
the preset position number.
●To Return to the Setup Menu
• Move the cursor to RET and press the CAM (SET) key.
2S 3S 5S 10S 30S 1MIN 2MIN 3MIN 4MIN
** SCENE FILE 1 **
SHUTTER
AGC
WHITE BAL
AF MODE
RET
OFF
ON(MID)
ATW
MANUAL S
Scene file setting menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET DEL
ON
ALC
10S
1
••••••••|
L H
Preset setting menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET DEL
ON
ALC
10S
OFF
••••••••|
L H
Preset setting menu
** PRESET NUMBER SET **
2
6
10
14
18
22
26
30
1*
5
9
13
17
21
25
29
ID:DOOR
RET
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
PRESET NUMBER SET menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET DEL
ON
ALC
10S
OFF
••••••••|
L H
Preset setting menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET DEL
ON
ALC
10S
OFF
••••••••|
L H
Preset setting menu