Panasonic GA-AS16TPoE+ User manual

WEB
Reference
Layer 2 Switching Hub
Model No. PN25161/PN25168
PN25241/PN25248
PN25481/PN25488

2
The target model for this document is as follows.
Model name Model number Firmware version
GA-AS16TPoE+
PN25168-TH
PN25168-MY
PN25168-ID
PN25168-SG
1.0.0.07 and above
GA-AS24TPoE+
PN25248-TH
PN25248-MY
PN25248-ID
PN25248-SG
PN25248-NZ
1.0.0.07 and above
GA-AS48TPoE+
PN25488-TH
PN25488-MY
PN25488-ID
PN25488-SG
1.0.0.10 and above
GA-AS16T
PN25161-TH
PN25161-MY
PN25161-ID
PN25161-SG
1.0.0.07 and above
GA-AS24T
PN25241-TH
PN25241-MY
PN25241-ID
PN25241-SG
PN25241-NZ
1.0.0.07 and above
GA-AS48T
PN25481-TH
PN25481-MY
PN25481-ID
PN25481-SG
1.0.0.07 and above

3
Table of Contents
1. Product Outline .......................................................................................... 5
1.1. Features ................................................................................................. 5
1.2. LED Behavior .......................................................................................... 6
1.2.1.LED Behavior during Start-up ............................................................. 6
1.2.2.LED Behavior while Operating ........................................................... 7
1.2.3.Operation Overview of PoE Power Supply Function ........................... 9
2. Installation ............................................................................................... 10
3. Connection .............................................................................................. 11
3.1. Connecting a Twisted Pair Port ............................................................. 11
3.2. Connecting to Power ........................................................................... 12
4. Web Browser-based Control ..................................................................... 13
4.1. Operating Environment ........................................................................ 13
4.2. IP Address Configuration ...................................................................... 14
4.3. Access to Web Control Function ........................................................... 15
4.4. Displaying Basic Information ................................................................. 17
5. Switch Configuration ............................................................................... 19
5.1. Basic Config ......................................................................................... 19
5.1.1.Administration Config ..................................................................... 19
5.1.2.IP Config ......................................................................................... 20
5.1.3.Basic Port Config ............................................................................. 21
5.1.4.Extend Port Config .......................................................................... 23
5.1.5.Power Saving Config ....................................................................... 24
5.1.6.System Security ............................................................................... 25
5.1.7.Syslog Transmission Config ............................................................. 26
5.1.8.ID/Password Change ....................................................................... 27
5.1.9.FDB Table ........................................................................................ 28
5.1.10.Time Config .................................................................................. 29
5.1.11.Static ARP Table ............................................................................ 30
5.1.12.ARP Table ..................................................................................... 31
5.2. Advanced Switch Configuration ........................................................... 32
5.2.1.VLAN Management ........................................................................ 32
5.2.1.a. VLAN Modification ............................................................... 34
5.2.2.VLAN Creation ................................................................................ 35
5.2.3.VLAN Port Config ............................................................................ 36
5.2.4.Traffic Class Config .......................................................................... 37
5.2.5.Diffserv Config ................................................................................ 38
5.2.6.Link Aggregation Config ................................................................. 39
5.2.6.a. Link Aggregation Modification ............................................. 40
5.2.7.Storm Control Config ...................................................................... 41
5.2.8.Port Monitoring Config ................................................................... 42
5.2.9.Static Multicast Address Config ....................................................... 44

4
5.2.10.PoE Port Config ............................................................................. 45
5.2.11.PoE Global Config ......................................................................... 47
5.2.12.Loop Detection Config .................................................................. 48
5.2.13.Loop History Info ........................................................................... 50
5.2.14.Port Group Config ......................................................................... 51
5.3. System Tools ........................................................................................ 52
5.3.1.Software Update ............................................................................. 52
5.3.2.Reboot ............................................................................................ 53
5.3.3.Save Current Config ........................................................................ 54
5.3.4.Statistics .......................................................................................... 55
5.3.5.System Log ..................................................................................... 58
5.3.5.a. System Log Config ............................................................... 62
5.3.6.Config File Transfer ......................................................................... 63
5.3.7.Ping Execution ................................................................................ 64
5.3.8.Exception Handler ........................................................................... 65
5.3.9.Watchdog Timer ............................................................................. 66
6.Appendix ...................................................................................................... 67
6.1. Specifications ....................................................................................... 67
6.2. Easy IP Address Setup Function ............................................................ 70
6.3. Network Configuration Example and Notes Using Loop Detection and
Blocking Function 71

5
1. Product Outline
GA-AS16TPoE+/AS24TPoE+/AS48TPoE+/AS16T/AS24T/AS48T are Ethernet
Switching Hubs that feature the Web control function and 10/100/1000BASE-T
ports.
The downlink ports support the PoE power supply function for IEEE802.3at/af
compatible devices.
1.1. Features
・ All ports (twisted pair ports) are 10/100/1000BASE-T ports that support auto-
negotiation.
Speed and communication mode can be switched by configuring the settings.
・ The downlink ports can provide PoE power supply to IEEE802.3at and
IEEE802.3af compatible devices.
A single port can supply power by PoE up to 30 W.
The total number of ports, number of downlink ports, and amount of power
supply by the whole unit are shown below for each model.
・ All twisted pair ports support the auto sensing function of a straight/cross cable.
You can simply connect devices with the straight cable, whether the target is a
terminal or a network device. (By factory default, downlink ports are fixed to
MDI-X.)
・ The IEEE802.3az (LPI) compatible Energy Efficient Ethernet (EEE) function is sup-
ported, allowing reduction of power consumption of each port by automatically
switching to a power saving state when there is no data communication at link
up.
・ The power saving mode automatically detects the connection status, and
reduces power consumption to a minimum.
・ The IEEE802.1Q compatible tag VLAN is supported, allowing registration of up
to 256 VLANs.
・ The Internet Mansion function is supported, allowing to ensure security of each
room in a building.
・ The IEEE802.1p compatible QoS function is supported.
・ The IEEE802.3ad compatible link aggregation function is supported, allowing
aggregation up to 8 ports.
Model name Total number of ports
Number of downlink
ports
(PoE power supply
supported)
Power supply by the
whole unit
GA-AS16TPoE+ 18 (port 1 to 18) 16 (port 1 to 16) 112W
GA-AS24TPoE+ 26 (port 1 to 26) 24 (port 1 to 24) 168 W
GA-AS48TPoE+ 50 (port 1 to 50) 48 (port 1 to 48) 336 W

6
1.2. LED Behavior
1.2.1. LED Behavior during Start-up
When you turn on this switch, all LEDs are lit momentarily.
Then, self-diagnosis of the hardware is conducted. When the self-diagnosis is com-
pleted, the STATUS LED is lit in green, and the hardware starts operation as a
switching hub.

7
1.2.2. LED Behavior while Operating
Each switch has system LEDs and a set of LEDs for each port. These LEDs indicate
the operation status of the switch and each port.
・ System LEDs
Figure 1-1 System LEDs
LED names Behavior Description
POWER LED Green light Power On.
Off Power Off.
STATUS LED Green light System operating normally.
Orange light System starting-up.
Orange blink System failure.
PoE LIM. LED
* PoE supported devices
only
Off Supplies power in the range of:
GA-AS16TPoE+: 0 to 105 W
GA-AS24TPoE+: 0 to 161 W
GA-AS48TPoE+: 0 to 329 W
Green light Supplies power in the range of:
GA-AS16TPoE+: 105 to 112 W
GA-AS24TPoE+: 161 to 168 W
GA-AS48TPoE+: 329 to 336 W
Green blink When power supply by the whole
unit exceeds:
GA-AS16TPoE+: 124 W
GA-AS24TPoE+: 168 W
GA-AS48TPoE+: 336 W

8
・ Port LEDs
Figure 1-2 Port LEDs
Port LEDs Behavior Description
Left LINK/ACT Green
light
Link established.
Green
blink
Transmitting data.
Off No device connected.
Right PoE Green
light
Supplying power normally.
Green
blink
The whole unit or the single port is overloaded.
Off Not supplying power, or no PoE power receiving
device connected.
Port LED (Left)
Port LED (Right)

9
1.2.3. Operation Overview of PoE Power Supply Func-
tion
The downlink ports can provide PoE power supply for IEEE802.3at/af compatible
devices. A single port can supply power up to 30 W.
The number of downlink ports and amount of power supply by the whole unit are
shown below for each model.
・ Power supply operation when the PoE LIM. LED is orange blink (the whole unit
is overloaded)
When the whole unit is overloaded due to a power request exceeding the limit,
you can check which port has stopped supplying power, by checking whether
the port LED (right) is green blink. To keep power request less than maximum
power supply on the whole unit, unplug the cable connected to the port green
blink.
Priority control of the power supply can be set and changed from the web con-
trol screen. (By factory default, the priority of all downlink ports is set as the
same.)
・ Power supply operation when a single port is overloaded
When power request exceeds the maximum on a single port, the port is over-
loaded and stops supplying power. You can check which port has stopped sup-
plying power, by checking whether the port LED (right) is green blink. Unplug
the cable on the port green blink.
Note: Power consumption may be greatly different between during normal opera-
tion and during maximum power consumption depending on the PoE power
receiving device. Configure the switch not to exceed the limit.
Note: When priority control is not set or the priority is set as the same for all ports,
the port with the smallest port number will be given priority for power supply.
(If power request exceeds the limit of the whole unit, a port with a larger port
number is blocked to stop supplying power.)
Model name Number of downlink ports
(PoE power supply supported)
Power supply by the
whole unit
GA-AS16TPoE+ 16 (port 1 to 16) 112 W
GA-AS24TPoE+ 24 (port 1 to 24) 168 W
GA-AS48TPoE+ 48 (port 1 to 48) 336 W

10
2. Installation
For the installation methods for each model, refer to the operating instructions.

11
3. Connection
3.1. Connecting a Twisted Pair Port
・ Connection Cable
Use a CAT5E or higher straight cable (twisted pair cable) with 8P8C RJ45 modu-
lar plugs.
・ Network Configuration
Figure 3-1 Connection configuration example
The length of the cable connecting this switch and a device must be 100 m or
shorter. When a terminal or a LAN device with auto-negotiation function is con-
nected to a port, the port is automatically configured to the most appropriate per-
formance mode. When a terminal or a device without auto-negotiation function is
connected to a port, this switch automatically determines and sets the communica-
tion speed; however, the full-duplex/half-duplex configuration is set at half-duplex
because the full-duplex/half-duplex capability cannot be determined. When con-
necting a terminal or a device without auto-negotiation function, set the connec-
tion mode of the port to Fixed. For detailed configuration procedure, refer to
Section 5.1.3.
Note: If connection mode is set to a fixed value, Auto-MDI/MDI-X function does not
work. Therefore, you need to use a cross cable for connections between
switches.
Within 100 m
Within 100 m
Within 100 m

12
3.2. Connecting to Power
Connect the supplied power cord to the power port of this switch, and connect
the power plug into an electric outlet.
The switch operates at AC 100-240 V (50/60 Hz).
It does not have a power switch. When you connect the power plug, the switch
turns on and starts operating.
To power off, unplug the power plug from the electric outlet.

13
4. Web Browser-based Control
With the web browser-based control function (hereinafter referred to as the "Web
control function"), you can configure the settings for this switch from a web
browser's user interface via the network.
The letters, numbers, and symbols that can be used for setting are as follows.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
1234567890
-._
The example setting screen used in this document may differ from the actual
screen.
4.1. Operating Environment
The recommended web browser is Microsoft Internet Explorer 11.
Note: When you use a proxy, the active window may not be displayed properly;
direct access without using a proxy is recommended.

14
4.2. IP Address Configuration
The IP address of this switch is not set as factory default. To access the Web con-
trol function screen for this switch, you need to use the ZEQUO assist Plus applica-
tion that can be downloaded from HP with the switch to set the IP address.
For details, refer to the operation instructions for ZEQUO assist Plus.

15
4.3. Access to Web Control Function
To use the Web control function, enter the IP address for this switch in the web
browser's URL field ("location:", "address:", etc.) and press "Enter." Then, a login
screen for this switch shown in Figure 4-1 is displayed. Enter the user name and
password.
The factory default user name is "manager" and password is "manager."
Figure 4-1 Login Screen
Note: If the login screen is not displayed, check the following:
(1) Are the IP address, subnet mask, and default gateway of this switch
properly configured?
(2) Is the IP address entered on the web browser the same as the IP
address of this switch?

16
When the above information has been authenticated properly, the screen shown
in Figure 4-2 will appear for selecting a display language.
Select the type of the language in which you want to show menus, and press "OK."
Figure 4-2 Select Display Language
The left side of the screen shows a list of actions that you can perform on this
screen.
(1) General Information:
Displays a list of basic information of this switch.
(2) Basic Config:
Configure the basic settings such as IP address and port settings.
(3) Advanced Config:
Configure the advanced function settings such as VLAN, QoS, and port moni-
toring.
(4) System Tools:
Management tools to update the firmware and browse system logs.
To conduct operation management, it is recommended that you first configure
settings for the "Basic Config" and then configure other advanced settings.

17
4.4. Displaying Basic Information
Select "General Info" to open the screen shown in Figure 4-3. This screen displays a
list of this switch's basic information.
Figure 4-3 General Info

18
Screen Description
System Informa-
tion
Displays the operating time and firmware version of this switch.
Operating Time Displays the cumulative time since the power on of this
switch.
Boot Code Ver-
sion
Displays the firmware version of this switch. * The firmware
update described in Section 5.3.1 is available only for run-
time codes.
Runtime Code
Version
Hardware Displays the hardware information.
Serial Number Displays the serial number of this switch.
Hardware Ver-
sion
Displays the hardware version.
DRAM Size Displays the size of the installed DRAM.
Flash Size Displays the size of the installed Flash memory.
Management Configure the items shown here in accordance with Section 5.1.1 "Administra-
tion Configuration."
Host Name Displays the switch name. The factory default setting is
blank. For configuration details, refer to Section 5.1.1.
System Address Configure the items shown here in accordance with Section 5.1.2 "IP Config."
MAC Address Displays the MAC address of the switch. This value is
uniquely assigned to each device and cannot be changed.
IP Address Displays the switch's current IP address. The factory default
setting is "0.0.0.0". For configuration details, refer to Section
5.1.2.
Subnet Mask Displays the switch's current subnet mask. The factory
default setting is "0.0.0.0". For configuration details, refer to
Section 5.1.2.
Default Gate-
way
Displays the IP address of the router for the default gate-
way. The factory default setting is "0.0.0.0". For configura-
tion details, refer to Section 5.1.2.

19
5. Switch Configuration
After completing configuration, you must save the configuration information in
accordance with Section 5.3.3. Unless you save the configuration information, the
settings configured so far will not be reflected upon restart.
5.1. Basic Config
5.1.1. Administration Config
Select "Basic Config" and then "Administration Config" to open the screen shown
in Figure 5-1. Select this screen to display this switch's information. On this screen,
you can set administrative information, such as device name.
Figure 5-1 Administration Configuration
Screen Description
Product Name Displays the system information. This item is not editable.
Host Name Displays the system name. The factory default setting is blank.

20
5.1.2. IP Config
Select "Basic Config" and then "IP Config" to open the screen shown in Figure 5-2.
On this screen, you can configure the IP address of this switch.
Figure 5-2 IP Config
Screen Description
Note: All IP addresses on the local network must be unique, and no duplications are
allowed. In addition, you need to set the subnet mask and the default gate-
way, which are the same for other devices on the same subnet using this
switch. If you are unsure, consult the network administrator.
MAC Address Displays the MAC address of this switch. This value is uniquely assigned to each
device and cannot be changed.
IP Address Displays the current IP address. The factory default setting is "0.0.0.0".
Subnet Mask Displays the current subnet mask. The factory default setting is "0.0.0.0".
Default Gateway Displays the IP address of the router, set as the current default gateway.
The factory default setting is "0.0.0.0".