Panasonic AV-HS300 User manual

Before operating this product, please read the instructions carefully and save this manual for
future use.
Operating Instructions
Multi-Format Compact Live Switcher
Model No. AV-HS300

2
indicates safety information.
This class A digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe A
est conforme à la norme NMB-003 du
Canada.
For CANADA
Safety precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (service) instructions in the
literature accompanying the appliance.
WARNING:
• TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
• THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING AND THAT
NO OBJECTS FILLED WITH LIQUIDS, SUCH
AS VASES, SHALL BE PLACED ON THE
APPARATUS.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE,
USE THE RECOMMENDED ACCESSORIES
ONLY.
FCC Note:
This equipment has been tested and found
to comply with the limits for a class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when
the equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy, and
if not installed and used in accordance with
the instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
Warning:
To assure continued FCC emission limit
compliance, the user must use only shielded
interface cables when connecting to external units.
Also, any unauthorized changes or modifications
to this equipment could void the user’s authority to
operate it.
CAUTION:
In order to maintain adequate ventilation, do
not install or place this unit in a bookcase,
built-in cabinet or any other confined space.
To prevent risk of electric shock or fire hazard
due to overheating, ensure that curtains
and any other materials do not obstruct the
ventilation.
Note:
The rating plate (serial number plate) is on
the bottom of the unit.
The socket outlet shall be installed near the
equipment and easily accessible or the mains
plug or an appliance coupler shall remain readily
operable.
A warning that an apparatus with CLASS I
construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
WARNING:
TO PREVENT INJURY, THIS APPARATUS
MUST BE SECURELY ATTACHED TO THE
FLOOR/WALL IN ACCORDANCE WITH THE
INSTALLATION INSTRUCTIONS.

3
indicates safety information.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install
in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources
such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding-type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord form being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
Read these operating instructions carefully before using the unit. Follow the safety instructions on the
unit and the applicable safety instructions listed below. Keep these operating instructions handy for future
reference.
IMPORTANT SAFETY INSTRUCTIONS
Safety precautions

4
Contents
Description .............................................. 5
Features ................................................... 5
1. Parts and their functions ................... 6
1-1 Control panel ................................................. 6
1-2 Crosspoint area ............................................. 7
1-3 Wipe area ...................................................... 8
1-4 Transition area ............................................... 9
1-5 LCD menu area ........................................... 10
1-6 Rear panel connections area ...................... 11
2. Basic operations ............................... 12
2-1 Transitions ................................................... 12
2-1-1 Selecting the bus ................................... 12
2-1-2 Selecting the bus mode ......................... 12
2-1-3 Selecting the transition mode ................ 13
2-1-4 Manual transition
(using the fader lever) .......................... 13
2-1-5 Auto transition ........................................ 13
2-2 Wipe ............................................................ 14
2-2-1 Selecting the wipe pattern ..................... 14
2-2-2 Selecting the wipe direction ................... 14
2-2-3 Wipe decorations
(border, soft effect)
............................... 14
2-3 Key .............................................................. 16
2-3-1 Selecting the key source ....................... 16
2-3-2 Setting the key ....................................... 17
2-3-3 Key adjustments .................................... 17
2-3-4 Selecting key fill ..................................... 18
2-3-5 Key decorations ..................................... 19
2-4 Color background ........................................ 21
2-5 Freezing the input signals ........................... 22
2-6 Frame memory ............................................ 23
2-7 Preset memory ............................................ 24
3. Setup .................................................. 26
3-1 Setting the input signals .............................. 26
3-1-1 Setting the input signals (IN 1 to 5) ....... 26
3-1-2 Setting the input signal frame
synchronizer ........................................ 26
3-1-3 Setting the DVI input signals .................. 27
3-2 Setting the output signals ............................ 29
3-2-1 Types of output signals .......................... 29
3-2-2 Selecting the AUX signals ..................... 29
3-3 Selecting the video format ........................... 30
3-4 Setting the crosspoints ................................ 31
3-4-1 Assigning signals to the crosspoints ...... 31
3-4-2 Setting the crosspoint switching ............ 32
3-5 Setting the sync signals .............................. 33
3-6 Adjusting the output signal phase ............... 34
3-7 Network settings .......................................... 36
3-8 Other settings .............................................. 38
3-8-1 LCD backlight ........................................ 38
3-8-2 Setting the ancillary data ....................... 38
3-8-3 BB signal setup level ............................. 38
3-9 Status displays ............................................ 39
3-10 Initialization ................................................. 39
4. Setting menu table ............................ 40
5. Image transmission functions ......... 45
6. External interfaces ........................... 49
6-1 RS-422 connector ....................................... 49
6-2 GPI connector ............................................. 49
6-3 Tally connector ............................................ 49
7. Connections ...................................... 50
8. Appearance ....................................... 52
Specifications and
standard accessories ........................... 53
Appendix (glossary) ............................. 55

5
Description
This unit is a single-ME digital video switcher which supports multiple HD and SD formats. While featuring
compact dimensions, it can optionally support HD analog component inputs (5) in addition to the five SDI inputs
and one DVI-I input. Since a frame synchronizer is incorporated for each of the inputs, signals can be switched
without “shocking” or “freezing” non-synchronized video signals. Furthermore, the images created by a PC can be
imported via Ethernet.
Features
 Six inputs, three outputs supported despite its compact size
The standard configuration consists of six inputs (five SDI inputs and one DVI-I input) and three SDI outputs
(PGM, PVW and AUX). Optionally, the unit is also capable of supporting HD analog component inputs (5).
The SDI inputs support active through outputs. Key inputs can be selected from the six video inputs for use.
 Multiple formats supported
HD formats (1080/59.94i, 1080/50i, 720/59.94p and 720/50p), SD formats (480/59.94i and 576/50i) and DVI-I
(input only) are supported as the signal formats.
 Frame synchronizer system and external sync system supported
The unit contains a high-performance 10-bit frame synchronizer to enable non-synchronized images to be
input. By using the BB signal output, a system can be configured using the switcher’s sync signals as a
reference. Gen-lock is also possible with external sync signals (BB or TRI signals).
 Built-in effects and key combination functions
The unit provides nine different waveform patterns as wipe patterns to add borders or soft effects.
Key combination supports self keys and linear keys, and key inversion is also possible.
 Ethernet and control interfaces supported
The unit can import images created on a PC into its frame memory over Ethernet (100 Mbps or 10 Mbps) and
use them as background images or key input signals.
External control using RS-422 or GPI signals is also supported. In addition, the unit comes with six tally
outputs.
 External power supply system
The unit is powered by an external DC 12 V power supply so it can be used not only indoors but in the field as
well. (However, the unit is not constructed to be rain-proof or drip-proof so keep it away from rain or moisture.)
 Easy operability
The simple panel layout which enables the functions to be operated directly enables speedy live transmissions.
Preset-like operations can be performed on the LCD panel using a menu-driven format.

6
1. Parts and their functions
1-1. Control panel


    

 


     

 Power indicator [POWER]
This lights when the power switch () is set to ON while power is supplied to the DC power socket.
It goes off when the power switch () is set to OFF.
 Power switch
When this switch is set to “ I ” while power is supplied to the DC power socket, the unit’s power is turned
on, and the power indicator () lights. When it is set to “O”, the unit’s power is turned off, and the power
indicator () goes off.
 Alarm indicator [ALARM]
This lights when the fan has stopped running or when something is wrong with the DC power (such as a drop
in voltage). Which type of trouble has occurred can be checked on the LCD’s status menu. Contact your dealer
if the indicator remains lighted.

7
1. Parts and their functions
1-2. Crosspoint area
 PGM/A bus crosspoint switches [PGM/A 1 to 7]
These are used to select the PGM/A bus video signals. In the case of the flip-flop system, the main line video
(PGM) signals are always selected.
 PST/B bus crosspoint switches [PST/B 1 to 7]
These are used to select the PST/B bus video signals. In the case of the flip-flop system, the images inserted
next (PST) are always selected. When a B bus crosspoint switch is pressed while one of the source selector
switches () is held down, key signals or AUX signals are selected.
 Source selector switches [SOURCE SELECT/AUX, KEY-S, KEY-F]
When a B bus crosspoint switch () is pressed while the [AUX] source selector switch is held down, the AUX
signals are selected, and when a B bus crosspoint switch () is pressed while the [KEY-S] or [KEY-F] source
selector switch is held down, the key signals are selected.
While a switch is held down, its indicator lights in amber.
In addition, if the [CLN], [PVW] or [PGM] wipe pattern selector switch () is pressed while the [AUX] switch is
held down, the switch will operate as an AUX bus selector switch.
[CLN]: Clean signals are output to the AUX bus.  See 3-2-2
[PVW]: PVW signals are output to the AUX bus.  See 3-2-2
[PGM]: PGM signals are output to the AUX bus.  See 3-2-2

8
1. Parts and their functions
1-3. Wipe area
 Wipe pattern selector switches [WIPE PATTERN / FUNC]
These are used to select the wipe patterns. Each switch is used to select one
of the nine wipe patterns.
The indicator of the switch for the selected pattern lights (in amber).
When the [FUNC] switch () has been pressed and its indicator is lighted, the
function setting menu is selected, and the indicator lights up green.
 Wipe direction selector switch [N N/R R]
This is used to select the wipe direction.  See 2-2-2
[N]: For setting the wipe direction to the normal direction.
[N/R]: To switch the wipe direction between normal and reverse when the execution of the transition has
been completed.
[R]: For setting the wipe direction to the reverse direction.
 [FUNC] switch
When this switch is pressed, its indicator lights up green. If a wipe pattern selector switch is pressed while
its indicator is lighted, the wipe pattern selector switch lights up green, and the setting menu of the function
indicated underneath the switch appears on the LCD display.
[TIME]: For setting the auto transition time.  See 2-1-5
[WIPE]: For setting the wipe border and soft effect.  See 2-2-3
[CBGD]: For setting the color background.  See 2-4
[KEY]: For setting the key.  See 2-3
[EDGE]: For setting the key edge.  See 2-3-5
[FRZ]: For displaying the freeze status display and setting freezing.  See 2-5
[MEM]: For setting the preset memory or frame memory.  See 2-6, 2-7
[XPT]: For displaying and setting the crosspoint assignment.  See 3-4
[SETUP]: For performing the system settings.  See 3
 Freeze status indicator LED
When this LED is lighted, it means that one of the input signals is frozen.
When the [FUNC] switch () is pressed and its indicator is lighted and then the [FRZ] switch is pressed, the
freeze status is indicated for each input. (An asterisk ( ) appears above the name of a frozen crosspoint.)
Bear in mind that since the signals are frozen while the indicator is lighted, the unit’s output will remain
unchanged even if the input images change.
(When crosspoints 3 and 5 are frozen)
ＦＲＺ
１／２
ＦＲＺ： ＊ ＊
ＸＰＴ： １２３４５６７

9
1. Parts and their functions
1-4. Transition area
 [BKGD] switch
This executes the background transition when the [AUTO] switch () or fader lever
() has been operated.
When the [BKGD] switch is pressed and it is selected, its indicator is lighted in red.
If the [KEY] switch () is now pressed, the indicator goes off, and the de-selected
status is established.
However, when the [BKGD] switch and [KEY] switch () are pressed at the same
time, both switches are set to the selected status.
The selection status cannot be changed while a transition is being executed or
suspended.
 [KEY] switch
This executes the key transition (MIX) when the [AUTO] switch () or fader lever () has been operated.
When the [KEY] switch is pressed and it is selected, its indicator is lighted.
When a transition is executed and the key ON status is established, the [KEY] switch lights in red. When
another transition is executed and the key OFF status is established, it lights in amber.
If the [BKGD] switch () is now pressed, the indicator goes off, and the de-selected status is established.
However, when the [BKGD] switch () and [KEY] switch are pressed at the same time, both switches are set to
the selected status.
The selection status cannot be changed while a transition is being executed or suspended.
 KEYON status indicator LED
This lights in red when the key ON status is established.
 [MIX] switch
This is used to switch the A and B bus images while making them overlap.
During the transition, the A and B bus output total is kept at 100 %.
When the [MIX] switch is pressed and it is selected, its indicator lights in amber.
If the [WIPE] switch () is now pressed, it goes off, and the de-selected status is established.
 [WIPE] switch
This is used to execute the transition using the pattern selected by the wipe pattern selector switch ().
When the [WIPE] switch is pressed and it is selected, its indicator lights in amber.
If the [MIX] switch () is now pressed, it goes off, and the de-selected status is established.
 [AUTO] switch
This is used to automatically execute transitions (auto transition) using the transition time which has been set.
During auto transition its indicator lights in red. When the switch is pressed again during auto transition, the
auto transition operation is suspended, and the indicator lights in green. When it is pressed again while auto
transition is suspended, the remaining transition is executed.
The indicator goes off when auto transition is completed.
When the [AUTO] switch is pressed while the fader lever () is at an interim position, the remaining transition
is executed using the transition time which has been set.

10
1. Parts and their functions
 Fader lever
This is used to execute background or key transitions. When it is moved as far as it will go, the transition
is completed. When it has been operated during auto transition, auto transition will be switched to manual
operation as soon as the fader position overtakes the amount of the transition being executed.
 Bus tally LEDs
These indicate the output statuses of the A bus and B bus. The LED corresponding to the bus whose program
signals (PGM) are being output lights.
1-5. LCD menu area
 LCD
The setting menus are displayed on the LCD.
When the [FUNC] switch () is pressed and its indicator is lighted and then one of the wipe pattern selector
switches () is pressed, the setting menu for the function concerned is displayed.
 Rotary encoders [F1] to [F4]
These are used to set the parameters displayed on the menu.
Menu items are selected and parameters set by rotating [F1] to [F4]. For details on their operation, refer to the
items in “2. Basic operations”.
When the [F1] to [F4] switches are held down, the parameters are returned to their default status.
(Numerical value setting items only)
(Initial screen)
＜ＡＶ－ＨＳ３００＞
ＶＥＲ１．００