Panasonic TC-51PM10ZQ User manual

Panasonic
Operating Instruction
Coiour Television
TC-51PM10ZQ
Please read the operating instructions completely before operating this set.
TQB4G2053@

(Pear Panasonic customer)
Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new colour television.
(Safety Instructions^
The TV set can be operated on
AC AUTO 110-240V. 50/60Hz.
The cabinet and picture tube can
be kept in good condition by
simply wiping with a clean, soft
cloth moistened with miid
detergent and water. Do not use
solutions containing benzol,
petroleum or a chemical cloth.
For safety, remove the plug from
the wall outlet.
To prevent damage which may
result In fire or electrical shock,
do not expose the TV set to rain
or excessive moisture.
Adequate ventilation is essential
to prevent failure of electrical
components.
Do not remove the rear cover, as
live parts are accessible when It
Is removed.
Avoid exposing the TV set to
direct sunlight and other source
of heat.
Remove the plug from the wall
outlet (Power point) when the TV
set is not used for a prolonged
period of time.
Do not use this set If abnormal
operation occurs.
EX; smoke, odd sounds or
smells, turn the power switch off
and disconnect the AC power if
you notice any unusual
operation.
2

(Before Operating This Set)
Connect the Aerial Cable to the RF In Terminal
VHF Aerial
To obtain the best quality picture and sound, an external antenna, the correct cables (75 Ohm coaxial) and
the correct terminating plug will be required.
If a communal antenna system is used, you may require the correct connection cable and plugs between
the wall antenna socket and your television receiver.
Your local Television Service Deafer may be able to assist you in obtaining the correct antenna system for
your particular area and accessories required.
Any matters about antenna installation, upgrading of existing systems or accessories required, and the
cost incurred, are the responsibility of the customer.
Note :
if your existing antenna system uses 300 Ohm to 75 Ohm Baiun, see Below.
3

Batteries: Us® two “R6 (AA)” size batteries.
Insert the batteries ensuring correct polarity.
This is identifiable by the “+” and symbols on both the
batteries and inside the battery compartment.
Do not use rechargeable (Ni-Cd) batteries.
They are different in shape and perfomnance and may fail to ensure correct operation.
A Battery cautions
The incorrect use of batteries can cause electrolyte leakage which will corrode the Remote Control or
cause the batteries to burst.
Old Batteries New Batteries
Replacement both batteries at the same time. Don’t mix battery types Don’t Recharge,
(alkaline with cartKin zinc, etc.)
4

To watch the VCR picture :
Connect the VCR cable to the AUDIO INPUT and VIDEO INPUT
terminals at the rear of TV.
Press the TV/AV selection button, set the VCR to the playback mode.
To watch or to return to the TV programme, press the TV/AV selection
button again.
If both AV IN terminals are connected at the same time, only front
AV input terminal can operate.
RF OUT
AUDIO VIDEO
_(Rea_rofTy)
o o
o o
OUTPUT INPUT
VIDEO >

FoNow the connection shown below w
You can either use the AV input at the
RF OUT AUDIO VIDEO
you want to copy a programme from another tape (VCR)
k or the front of the TV.
Recording equipment
(recording)
tl—^
0
0
0
0
0
0
Panasonic
i----1
AUDIO VIDEO

Preset TV / AV
button button
Volume Up and
Down Buttons
Channel Up and Headphones AV IN
Down Buttons
Model Name Plate
Connecting Headphones
When a headphones plug is inserted into the Headphones socket all
disconnected: only the Headphones will function.
speakers will be automatically
^ jniAV IN«>g
VIDEO AUDIO
N
?(oo )
(Optional)
(not supplied)

Flow Chart of Mam Menu )
When the "MAIN MENU" button is pushed at the main menu screen, the screen display will return to the normal viewino
PrLelwh is pushed at each MENU screen {Picture. Sound, Features, Language
Preset), the screen display will return to the Main Menu screen.
8

1 .
To Switch Power on/off
The TV set must be switched on at the wall outlet and at the Main power switch.
Press this button to turn the TV set ON, from stand-by mode. Press it again to turn off.
Note:
When in the stand-by condition, it is possible to turn the TV set on by pushing the
Direct Programme Number Selection button (0-9) or the Programme Number up and
Down button.
Programme Number Selection
Press the programme number Up
* ■ A" or down " v “ Button to select
the next higher or lower
programme number.
Direct Programme Number Selection
(0-9)
6. g. To select programme number "1",
press the "1* button.
Two Digit Programme Number Selection
e.g. To select Programme Number “24".
Push the 0 button.
Push the 0 button.
Push the © button.
9

TV / AV Selection
Push the • TV/AV ” button to select TV
and AV input signal modes
sequentially.
Sound Mute Button
Push this button to mute the Sound
completely.
Push the button once again to restore
the previous sound level, and cancel
the mute.
The " Mute" symbol w/il! appear.
_I (Colour changes to Red)
^ 5 VOLUME
III-
Recall Button
Push the RECALL button to display the
current system status. Press this
button until display is cancelled.
Off Timer Button
The TV set may be preset to
switch to stand-by after a fixed
period.
By pressing "Off-Timer" button,
you can select the preset time either
30, 60, or 90 minutes.
030— ► Q e o
pio-*—P~| a uto^
1
030
1
When the off-timer
reaches its last 3
minutes, it starts blinking
before going to stand-by
condition.
Note:
Setting Off-timer to AUTO mode. If the set is not switched off, when the TV station ends broadcasting, it will automati¬
cally go to the stand-by condition after 5 minutes. This AUTO mode will not operate when the TV receiver is in AV mode.
How to cancel the OFF*timer setting;
1, Set the preset time condition to "0" mode by pressing the Off -timer button.
2. Turning the TV set off.
10