Panduit Atlona OmniStream AT-OMNI-311 User manual

Atlona Manuals
Networked AV
AT-OMNI-121
AT-OMNI-122
AT-OMNI-111
AT-OMNI-112
AT-OMNI-311
AT-OMNI-324
AT-OMNI-232
Solutions Setup and Conguration Guide
Single-Channel / Dual-Channel
Networked AV Encoder / Decoder
OmniStream™

OmniStream 2
Version Information
Version Release Date Notes
1 Feb 2019 Initial release
2Mar 2019 Audio added
3Mar 2019 USB added
4 May 2019 Added Network Switch Configuration, IR Control
5 Sept 2019 Updated AMS, Updating Device Firmware, and Configuring OmniStream Devices
sections with firmware 2.5 screenshots
6Aug 2020 Updated for AMS integration into Velocity with firmware version 2.1.0
7Oct 2020 Updated for Velocity with Integrated AMS firmware version 2.2.0

OmniStream 3
Introduction 4
Getting Started 5
Selecting a Network Switch 5
Velocity with Integrated AMS - Purchase or Download 5
Recommendations 5
Connections 6
Network Switch Conguration 7
Getting Started 7
VLAN Setup 9
IPv4 Interface and DHCP Setup 12
Port Mapping 18
Conguring IP Multicast 20
Creating User Accounts 24
Velocity with Integrated AMS 26
Getting an IP Address 26
Login 26
Updating 27
Discovery 29
Updating Device Firmware 31
Conguring OmniStream Devices 32
Testing Connectivity 37
IR Control 38
Controlling the Display using the Display’s IR Remote 38
Required Equipment 39
Connecting the IR Receiver to the Encoder 39
Connecting the IR Emitter to the Decoder 40
Identifying the Encoder using Velocity with Integrated AMS 41
Conguring the Encoder Serial Port 42
Conguring the Encoder Session 43
Conguring the Decoder Serial Port 45
Testing IR Functionality 48
Controlling the Display using a Control System 49
USB to IP Adapter 50
IP to Analog Audio Bridge 53
Video Walls 56
Table of Contents

OmniStream 4
Introduction
HDMI
HDMI
Encoder
Media Player
BluRay Player
AMS
Decoder
Decoder
Display
Display
4
media4
1 2
ID
PWR LINK
TM
O
MNI
S
TREAM
1 2
ID
PWR LINK
TM
O
MNI
S
TREAM
LAN
Network Switch
HDMI
HDMI
Ethernet
Ethernet
Ethernet
Ethernet
HDMI
PWR LINK
TM
O
MNI
S
TREAM
VOLUME
DISPLAY
INPUT
ID
1 2 1 2
This guide provides a base for setting up and conguring a small OmniStream™-based solution. The setup
instructions will provide information for building a system capable of sending and receiving audio and video through
OmniStream™ encoders and decoders, as well as a simple way to set up video walls and audio routing.

OmniStream 5
Getting Started
A network switch will be needed to power and pass IP trac. A list of certied switches is provided below with
download links for prebuilt congurations. Atlona recommends using a switch from the certied list to ensure
compatibility.
For conguration of the OmniStream devices with this guide, Velocity with integrated AMS (Atlona Management
System) will be needed. AMS has two options: AT-VGW-HW-3/AT-VGW-HW-10/AT-VGW-HW-20 hardware (with
integrated AMS) or AT-AMS-SW free software. AT-VGW-HW-3/10/20 can be purchased at: https://atlona.com/
product/vgw-hw/ or AT-AMS-SW free software can be downloaded from https://atlona.com/product/at-ams-sw/.
AMS will be needed before progressing further into this setup and conguration guide.
• When using multiple of the same OmniStream devices, or for reference, labeling can be used. It’s best to place
the label on the front of the device for visibility. When labeling, notate the last 4 numbers of the MAC address,
found on the bottom of the unit on the label, for easier IP discovery and notation later.
• Use a component surge suppressor with line conditioning for best results.
Certied Switcher Download Conguration
Cisco SG300-10MPP Box Download Link The default configuration can be found within the
OmniStream Certified Network Switches document
that can be found at https://atlona.com/pdf/
OmniStream_Certified_Switches.pdf.
Cisco SG300-28MP Box Download Link
Cisco SG300-52MP Box Download Link
Cisco SG350-10MP Box Download Link
Cisco SG350-28MP Box Download Link
Cisco SG350-52MP Box Download Link
Cisco SG550X-24MP Box Download Link
Cisco SG550X-48MP Box Download Link
Pakedge S3L-24P Box Download Link
Luminex GigaCore 26i Box Download Link
Ruckus ICX 7150-48ZP Box Download Link
Ubiquiti ES-48-500W /ES-48-750W Box Download Link
Selecting a Network Switch
Velocity with Integrated AMS - Purchase or Download
Recommendations
IMPORTANT: Atlona’s warranty does not cover damage due to electrical disturbances. A component
surge suppressor with line conditioning is highly suggested, especially in areas with electrical storms.

OmniStream 6
Initial connections can be done without installing the devices in their nal locations. Have at least one source and
display available to ensure video is passing between OmniStream devices. It is recommended these steps be
followed in the order they are written.
1. Connect all devices to the network switch using a CAT5e or higher cable. OmniStream devices will need to be
plugged into the PoE ports.
2. Have at least one source and display ready to connect to any of the OmniStream devices.
3. Once all the devices are connected to the network switch, connect the switch power supply to the power strip.
4. *Optional* If using the AT-OMNI-311, connect the USB B to USB A cable to the USB port of the PC, that will
provide the 5V power.
5. *Optional* If using the AT-OMNI-324, connect the power supply from the unit to the power strip.
6. *Optional* If using the AT-VGW-HW, connect it to the network switch.
7. *Optional* Connect the power supply to the AT-VGW-HW and power strip.
Connections

OmniStream 7
Network Switch Conguration
Getting Started
1. Connect a PC or laptop to the network switch. It is best to use the port that will remain on VLAN1 of the switch to
avoid the PC losing connection when settings are changed on the switch.
2. Go into the computer settings and change the IP of the PC to be on the same range as the switch.
Before working with the OmniStream devices, the network switch must be set up. This guide will provide instructions
for conguring a Cisco SG350X-24MP switch. The following steps will be the similar for most Cisco switches.
However, there may be small variations, depending on the switch model. Consult the switch User Manual for more
information.
NOTE: If the IP address of the network switch is 192.168.1.254, then the computer should be set
to 192.168.1.xx, where xx represents values from 1 to 253, as long as that IP address is not already
assigned on that network. The default IP address for all Cisco switches is 192.168.1.254/24.
3. Launch the desired web browser and enter the IP address of the network switch into the address eld, then
press [ENTER].
4. Enter the username and password. The default login credentials are as follows:
Username: cisco
Password: cisco
• VLAN Setup
• IPv4 Interface Setup
• Setting IP Multicast
• Setting up User Accounts
IMPORTANT: The Network Switch Conguration chapter is divided into ve sections. Each section
must be followed in the order listed below. Deviating from this order, or skipping steps within a
section, may result in unpredictable switch operation.

OmniStream 8
Network Switch Conguration
5. Click the Login button.
The switch will most likely require a new password to be assigned, before going further. This step may vary
depending on the network switch. Enter the desired password, as required.
6. Click the Apply button to commit changes.
7. The Getting Started page will be displayed.

OmniStream 9
Network Switch Conguration
8. Click the Display Mode drop-down list, near the upper-right hand corner of the screen, and select Advanced.
VLAN Setup
9. Select VLAN Management from the menu on the left side of the screen. The VLAN Management menu will
expand and the VLAN Settings page will be displayed. If the VLAN Setting page is not displayed, click VLAN
Management >VLAN Setting to display the page.
By Default, VLAN 1 is active. If the network is self-contained, skip to 15. Otherwise, continue with the next step.
10. Click the Add... button. The Add VLAN dialog will be displayed.
The purpose of creating a VLAN is to separate a network into separate logical areas / broadcast domains. In this
case, the VLAN is created to isolate AV-over-IP trac from normal network trac.

OmniStream 10
Network Switch Conguration
NOTE: VLAN 1 is the Cisco default VLAN. This VLAN can be used, but it cannot be modied or
deleted.
11. Enter the numerical ID of the VLAN in the VLAN ID eld. This value is required and must be within the range of 2
to 4094.
12. OPTIONAL: Enter a name for the VLAN in the VLAN Name eld. For example, the name of the VLAN could
be used to identify a department, within a company, which uses that broadcast domain. In this example,
“OmniStream” has been assigned as the name of VLAN 5.
13. Click the Apply button to commit changes. If the VLAN was successfully created, the dialog box will display a
“Success” message.

OmniStream 11
Network Switch Conguration
14. Repeat steps 11 through 13 to create as many VLANs as needed. If no additional VLANs are required, click the
Close button to dismiss the Add VLAN dialog box.
15. Click Administration, in the left-hand menu bar and select File Operations. The File Operations page will be
displayed.
16. Click the Duplicate radio button, next to Operation Type.
17. Click the Apply button to commit changes.

OmniStream 12
Network Switch Conguration
18. Click IP Conguration in the left-hand menu bar and select IPv4 Interface. The IPv4 Interface page will be
displayed.
19. Click the check box next to VLAN 1 (DHCP) and then click the Delete button.
IP Interface and DHCP Setup
The OmniStreams come with DHCP enabled. This section will congure the switch to become a DHCP server.

OmniStream 13
Network Switch Conguration
a. Click the check box next to VLAN 1.
b. Click the Edit button.
c. The Edit IP Interface dialog will be displayed.
d. Make make the required changes, then click the Apply button to commit changes.
e. Click the Close button to dismiss the Edit IP Interface dialog box.
20. Check the IP settings for VLAN 1. If no changes are required, continue with Step 21. However, if a dierent IP
address or subnet mask need to be specied, then follow the steps below:

OmniStream 14
Network Switch Conguration
NOTE: It is recommended that a static IP address be assigned to a VLAN, to avoid IP changes.
21. Click the Add... button. The Add IP Interface dialog box will be displayed.
22. Click the VLAN radio button, then click the drop-down list to select the VLAN that was created under VLAN
Setup (page 9).
23. Click the Static IP Address radio button.
24. Enter the IP address of the VLAN, in the IP Address eld. In the example below, 10.1.1.254 is used. However,
any available IP address in the pool may be used.
25. Click the Network Mask radio button and enter the subnet mask. In this example, 255.255.254.0 is used.
However, depending upon the requirements, any valid network mask may be used.
26. Click the Apply button to commit changes. Repeat Steps 21 through 25 for each additional VLAN, as necessary.
27. After all VLANs have been set up, click the Close button to dismiss the Add IP Interface dialog box.

OmniStream 15
Network Switch Conguration
28. Click DHCP Server in the left-hand menu bar under IP Conguration and select Network Pools. The Network
Pools page will be displayed.
29. Click the Add... button. A new pop up will appear.
30. Enter the Pool Name, Subnet IP Address, and Network Mask.
31. Enter starting and ending IP addresses in to the Address Pool Start and Address Pool End elds.
32. Select the Apply button. The pop up window will close.
NOTE: Steps 33 through 36 are optional and should only be used if there is a set of IP addresses that
need to be excluded from the server. If unneeded, skip to Step 37.
33. Select Excluded Addresses from under DHCP servers in the left side menu. The new page will open.

OmniStream 16
Network Switch Conguration
34. Enter any IP address range that the DHCP server will NOT assign to devices.
35. Press the Apply button.
36. Repeat for any/all IP ranges that should be excluded.
37. Click Properties in the left-hand menu bar from the DHCP Server menu. The new page will open.
38. Check the box next to Enable and press Apply to turn the unit into a DHCP server.

OmniStream 17
Network Switch Conguration
41. Click the Apply button to commit changes.
39. Click Administration, in the left-hand menu bar and select File Operations. The File Operations page will be
displayed.
40. Click the Duplicate radio button, next to Operation Type.

OmniStream 18
Network Switch Conguration
42. Click Port to VLAN from the VLAN Management menu. By default, the Membership Type, for each physical
port (interface), is assigned as Untagged.
43. Click VLAN ID equals to drop-down list and select the VLAN ID that was created under VLAN Setup (page
9).
44. Leave the AND Interface Type equals to drop-down list as Port of Unit 1. Click the Go button.
Port Mapping
45. The Membership Type, for the VLAN, will automatically be assigned as Excluded for each physical port on the
switch.

OmniStream 19
Network Switch Conguration
NOTE: If the port the PC is connected to is moved o VLAN1 to another VLAN (say VLAN5), then the PC
will need to be set to the IP settings of the new VLAN to continue.
46. Determine which physical ports will use the selected VLAN. Click the Membership Type drop-down list for each
physical port that will use the VLAN, and set its value to Untagged. For example, if physical ports 6 and 7 will be
used for VLAN 5, then set the Membership Type for these two ports to Untagged.
47. Scroll to the bottom of the list of ports and click the Apply button. Success messages will appear at the top and
bottom right of the screen.

OmniStream 20
Network Switch Conguration
48. Click Multicast from the menu bar on the left side of the screen. The Properties window will automatically be
displayed.
49. Click the Enable box, next to Bridge Multicast Filtering Status, to enable this feature.
50. Click the IP Group Address radio button, under both Forwarding Method for IPv6 and Forwarding Method for
IPv4.
51. Click the Apply button to commit changes.
52. Repeat steps 38 and 39 for each VLAN.
53. Click IGMP Snooping, under IPv4 Multicast Conguration, from the menu bar on the left side of the screen.
Conguring IP Multicast