Panduit Atlona AT-HDVS-CAM User manual

Installation Guide
AT-HDVS-CAM
1
PTZ Camera for HDVS-300 Soft Codec Conferencing System
AT-HDVS-CAM
The Atlona AT-HDVS-CAM is an enterprise-grade PTZ camera designed for use in video
conferencing and other applications such as lecture capture and distance learning. It features
a USB 2.0 interface for video and camera control. The HDVS-CAM seamlessly integrates
with the Omega™ Series, AT-OME-MS42-KIT, and OmniStream™ for a complete, automated
conferencing system that includes AV and USB extension. The HDVS-CAM delivers high
performance, professional-quality imaging with video resolutions up to 1080p @ 30 Hz, as well
as fast and accurate auto-focusing, and a fast yet quiet pan and tilt mechanism. Also available is
H.264 or H.265 streaming over IP with support for RTMP and RTSP protocols. This PTZ camera
is ideal for a wide range of small to medium-sized meeting spaces, classrooms, and training
rooms. The HDVS-CAM is available in black or white.
1 x AT-HDVS-CAM
1 x Wall mounting plate
1 x 1/4-20 UNC screw
1 x IR Remote Control
1 x USB A cable (2 meters)
1 x VISCA to RS-232 DB-9 adapter
2 x AAA battery
1 x 12 V DC Power Supply
1 x Installation Guide
Package Contents

Installation Guide
AT-HDVS-CAM
2
1 RS-232
Connect included VISCA to RS-232
adapter here to control the camera with a
third party software or hardware controller.
2 USB
Connect the included USB A cable from
this port to the USB port of the AT-OME-
MS42, AT-OME-EX-RX, or similar product.
3 LAN
Connect to a network switch to control
the unit via TCP/IP or webGUI.
4 DC 12V
Connect the included 12V power supply
to this port.
Panel Descriptions
1
0
X
Z
o
o
m
F
1
.
6
-
F
3
.
0
f
4
.
7
m
m
-
f
4
7
m
m
1
0
X
Z
o
o
m
F
1
.
6
-
F
3
.
0
f
4
.
7
m
m
-
f
4
7
m
m
IN
RS-232
OUT
USB LAN
DC 12V
USB
AT-HDVS-CAM
1 2 3 4

Installation Guide
AT-HDVS-CAM
3
Mounting Instructions
The AT-HDVS-CAM has two installation options, wall mount (included) and ceiling mount
(purchased separately).
Wall Mount installation
The install the AT-HDVS-CAM, 4 M6 swelling bolts, 1 1/4-20 UNC screw, 4 M6 nuts and shims,
the included wall mount bracket, and the AT-HDVS-CAM are required.
1 Install the M6 swelling bolts in a rectangular pattern on the wall, 100 mm wide and 50 mm
high.
2 Attached the wall mount bracket onto the wall, by placing them on the M6 swelling bolts
and securing it with the M6 nuts and shims.
3 Once the wall mount bracket is secure on the wall, place the camera on the top of the wall
mount bracket and secure it with the 1/4-20 UNC screw.
1
0
X
Z
o
o
m
F
1
.
6
-
F
3
.
0
f
4
.
7
m
m
-
f
4
7
m
m
1
0
X
Z
o
o
m
F
1
.
6
-
F
3
.
0
-
f
4
7
m
m
1
0
X
Z
o
o
m
F
1
.
6
-
F
3
.
0
f
4
.
7
m
m
-
f
4
7
m
m
1
0
X
Z
o
o
m
F
1
.
6
-
F
3
.
0
-
f
4
7
m
m

Installation Guide
AT-HDVS-CAM
4
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
1 Position part Aat the desired position on the ceiling / surface. Attach part Ato the ceiling /
surface by positioning screws (not provided) through the arc-shaped holes (1), as required.
2 Attach part Bto the bottom of the AT-HDVS-CAM using the included 1/4-20 UNC screw.
3 Attach part Ato part B, as shown below. Make sure the swivel joint on part Ais positioned
in the swivel notch on part B. Attach each of the four included screws, as shown, to secure
both parts of the mounting xture.
4 The completed assembly.
1 2
3
4
Ceiling Mount Installation
NOTE: The ceiling mount is sold separately.
Refer to https://atlona.com/product/at-hdvs-cam-cmnt/.

Installation Guide
AT-HDVS-CAM
5
ON KE
1 2
ON KE
1 2
NOTE: The camera picture will need to be inverted for video to be viewed
correctly. View the AT-HDVS-CAM manual for instructions on how to invert
video.
Ceiling Mount installation (Legacy Mount)
To install the AT-HDVS-CAM, 4 PA3X30 self-tapping screws, 4 PM3X6 screws, 4 screw stoppers,
1 1/4-20 UNC screw, the optional ceiling upper and lower covering plates, and the AT-HDVS-
CAM are required.
1. Install the 4 screw stoppers in the ceiling.
2. Connect the upper ceiling covering plate to the screw stoppers using the PA3X30 self-
tapping screws.
3. Connect the lower ceiling covering plate to the bottom of the AT-HDVS-CAM using the 1/4-
20 UNC screw.
4. Mount the lower ceiling covering plate to the upper ceiling plate using 3 PM3X6 bolts.

Installation Guide
AT-HDVS-CAM
6
Web Server
Installation
GND
RXD
CTS
TXD
RI
DSR
DSR
RTS
DCD
NC
TXD
DSR
DTR
GND
IR OUT
GND
RXD
VISCA VISCA
RS-232 RS-232
DTR
DSR
TXD
GND
RXD
GND
IR OUT
NC
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
NOTE: Atlona strongly discourages the use of USB cables beyond 12 feet
(3.5 meters) in length.
The AT-HDVS-CAM includes a built-in web server, which allows easy management and control of
all features. Follow the instructions below to access the web server.
1. Power the AT-HDVS-CAM by connecting the included power supply from the 12V power
receptacle on the camera to an available electrical outlet.
2. Connect a category cable (CAT-5e or better) from the network switch to the LAN port on the
camera.
3. Launch a web browser and enter the IP address of the AT-HDVS-CAM.
4. The AT-HDVS-CAM Registration page will be displayed.
5. Enter the username, password, and conrm the password on the registration page to
register the device. The password must contain a minimum of 8 characters, including 1
uppercase, 1 lowercase, and 1 numeric character.
6. Click on Register button.
7. The AT-HDVS-CAM Login page will be displayed.
8. Enter the username and password login credentials that were entered during the registration
process.
9. Click the Login button.
1. Connect the included power supply to the 12V power receptacle on the AT-HDVS-CAM.
2. Connect an Ethernet cable from the network to the LAN port on the back of the AT-HDVS-
CAM.
3. Connect a USB cable from the USB port to a conferencing system or to an extender, such
as the AT-OME-EX-RX.
4. OPTIONAL: Connect the VISCA to RS-232 cable to the RS-232 port for control. Note that
RS-232 can also be connected to an AT-OME-RX11 or other receiver that supports RS-232
for remote control.

Installation Guide
AT-HDVS-CAM
7
IR Remote
HOME
SET
F1 F2 F3 F4
1
AUTO
MANUAL
FOCUS ZOOM
2 3
123
456
789
*8 #
+
_ _
+
4
CAMERA SELECT
SET
PRESET
CLEAR
PRESET
BLC
ON/OFF MENU
The AT-HDVS-CAM comes with an IR remote control for full control of the camera and use of the
OSD menu. See the user manual for full information on the remote buttons, OSD, and presets.

Installation Guide
AT-HDVS-CAM
8
Troubleshooting
Problem Cause Solution
Why can I not get any
picture from my camera?
Camera lens is covered,
USB cables are faulty, or
the PC is not set up to
receive the video feed from
the camera.
• Remove the camera lens
cover from the unit.
• Try switching out the USB
cables for new ones.
• Bypass the HDVS-300 to
verify the unit isn’t having
compatibility issues.
• Check the device manager of
the PC to ensure the camera
USB device is discovering
correctly. If the device is
discovered, ensure the
camera is selected within the
video recording program (e.g.
Skype).
Why isn’t my video showing
correctly?
Resolution, focus, color,
and/or refresh rate may be
set incorrectly.
• Use the one of the control
interfaces (IR, RS-232,
or webGUI) to adjust the
resolution, focus the camera,
switch between 50 and 60
Hz, and many other settings.
Why is my IR remote not
working?
There is no power or too
much sunlight.
• Ensure there are fresh
batteries in the IR remote
control.
• Move the camera, so the
front panel IR window is out
of direct light.

Installation Guide
AT-HDVS-CAM
9
Notes

Installation Guide
AT-HDVS-CAM
10
Notes