Panduit ATLONA Opus AT-OPUS-RX41 User manual

1
Installation Guide
AT-OPUS-RX41
Opus 4K/UHD Three-Input HDMI Switcher
with HDBaseT input Auto-Switching
AT-OPUS-RX41
The Atlona AT-OPUS-RX41 is a 4×1 switcher and receiver for 4K high dynamic range (HDR) for-
mats. It features three HDMI inputs, plus an HDBaseT input for receiving video, embedded audio,
control signals, power, and Ethernet over distances of up to 330 feet (100 meters). Supporting
4K/UHD @ 60 Hz with 4:4:4 chroma sampling, as well as HDMI data rates up to 18 Gbps, the
OPUS-RX41 is the perfect complement to an Atlona Opus™ Series matrix switcher in whole-
house AV applications allowing display of 4K HDR content from either the matrix or one of the
connected local sources.
The OPUS-RX41 includes a number of key features to help simplify residential deployments.
Extension of CEC as well as bidirectional IR and RS-232 signals over HDBaseT allows a control
system connected to the OPUS-RX41 to select inputs on the matrix or control its sources, and
allows the matrix to control the local room display. A handheld IR remote control is included for
power and input selection on the OPUS-RX41. Advanced HDMI Audio Return Channel (ARC)
routes audio from a smart TV to both the local TOSLINK connection as well as HDBaseT. EDID
management, selectable 4K to 1080p downscaling, and HDCP 2.2 support with selectable
down-conversion to HDCP 1.4 ensures compatibility with legacy displays. Remote power allows
the device to be powered by an Opus matrix switcher, for installation exibility at a display or
projector.
IMPORTANT: Visit http://www.atlona.com/product/AT-OPUS-RX41 for the latest rm-
ware updates and documentation.
Package Contents
1 x AT-OPUS-RX41
1 x IR remote control
2 x Mounting brackets
4 x Mounting screws
1 x 5-pin captive screw connector
1 x 4-pin captive screw connector
1 x 5 V DC power supply
1 x Installation Guide

2
Installation Guide
AT-OPUS-RX41
OPTIONAL
RX TX TX RX
INPUT 4321 HDMI OUT DC 5VLAN
RX STX
RS-232 IR IN
OPTICAL
HDBaseT
RS-232 IR
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUSTM
Panel Descriptions
Front
1 2 3 4 5
1 IR window
Receives IR signals from the included IR remote control unit.
2 INPUT
Displays the active input. The active input will be indicated with a solid green light.
3 POWER
This LED indicator glows solid green when the unit is powered.
4 INPUT
Press and release this button to cycle through each of the four inputs. Each LED indicator
corresponds to each of the numbered inputs on the rear panel of the unit. The INPUT LED
indicators will indicate the active input with a solid green light.
5 FW
Connect a USB to mini-USB cable from this port to a computer to updated the rmware.
Refer to the User Manual for more information. USB cable not included.

3
Installation Guide
AT-OPUS-RX41
1 INPUT (HDBaseT)
Connect a category cable (CAT-5e or better) from this port to a compatible HDBaseT
transmitter. This category cable provides both data transfer and is used to power the AT-
OPUS-RX41.
2 INPUT (HDMI)
Connect an HDMI cable from each of these ports to an UHD/HD source.
3 OUTPUT (HDMI)
Connect an HDMI cable from this port to a display device.
4 OPTICAL
Connect a S/PDIF optical cable from this port to the TOSLINK port on an audio output
device.
5 HDBaseT RS-232 / IR
Connect a controller to this port to control a headend matrix (transmitter) over HDBaseT.
Refer to RS-232 Control (page 5) and IR Control (page 6) for wiring information.
6 RS-232 / IR IN
Connect a controller or PC to control the AT-OPUS-RX41 through RS-232 or IR. Refer to
RS-232 Control (page 5) and IR Control (page 6) for wiring information.
7 LAN
Connect an Ethernet cable to this port to control the AT-OPUS-RX41 using the built-in web
server or to control a sink device using pass-through IP control.
8 DC 5V
Connect the optional locking 5 V DC power supply to this power receptacle.
OPTIONAL
RX TX TX RX
INPUT 4321 HDMI OUT DC 5VLAN
RX STX
RS-232 IR IN
OPTICAL
HDBaseT
RS-232 IR
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUSTM
Panel Descriptions
Rear
21 3 4 5 6 7 8

4
Installation Guide
AT-OPUS-RX41
The AT-OPUS-RX41 includes an IR remote control
that can be used to operate the unit from a remote
location.
IR Remote Control
SW-R1
Video 1
Video
Video 2
All On
Power
Vol +
Vol
-
Mute
1
3
2
4
5
Input Audio
On Off
On Off
On Off
1 On / O
Press the On button to power-on the unit.
Press the O button to power-o the unit.
2 Input
Press these buttons (1 - 4) to select the desired
input.
3 Vol+ / Vol-
Press these buttons to increase or decrease the
volume level on the HDMI OUT port.
4 Mute
Press this button to toggle audio muting on the
HDMI OUT port.
1
4
2 3
Front Panel LED Indicators
The LED indicators on both the front and rear of the unit provide basic information on the current
status of the unit.
1, 2, 3, 4 Description
Solid green The input is the active input.
O The input is not selected.
POWER Description
Blue backlight Unit is powered.
O Unit is not powered.
IP MODE Description
Blue ashing
backlight (4x)
Flashes four times to indicate that the unit is set to DHCP mode.
Refer to IP Conguration (page 8) for more information.
Flashes blue (2x) Flashes two times to indicate that the unit is set to static
IP mode. Refer to IP Conguration (page 8) for more
information.
Solid blue Normal operating mode.

5
Installation Guide
AT-OPUS-RX41
The 5-pin HDBaseT RS-232/IR port provides bidirectional RS-232 control of a headend matrix
(transmitter) over HDBaseT. The 4-pin RS-232/IR IN port allows RS-232 control of the AT-OPUS-
RX41. Refer to the User Manual for more information.
Figure 1.1 - Wiring the 5-pin HDBaseT
RS-232/IR captive screw block for RS-232
control of a source device connected to
headend matrix.
Figure 1.2 - Wiring the 4-pin RS-232/IR IN
captive screw block for RS-232 control of the
AT-OPUS-RX41.
NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for
ground. On some devices functions of pins 2 and 3 are reversed.
RS-232 Control
1. Locate the required captive screw connector (included in the box).
2. Use wire strippers to remove a portion of the cable jacket.
3. Remove at least 3/16” (5 mm) of insulation from each of the wires.
4. Insert the wires into correct terminal. Refer to Figure 1.1 or Figure 1.2, below.
5. Connect the captive screw block to the proper port.
OPTIONAL
RX TX TX RX
INPUT 4321 HDMI OUT DC 5VLAN
RX STX
RS-232 IR IN
OPTICAL
HDBaseT
RS-232 IR
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUSTM
GND to control system
RX
TX
GND to control system
RX
TX

6
Installation Guide
AT-OPUS-RX41
The 5-pin HDBaseT RS-232/IR port can be used to either control a display device or a source
device over HDBaseT. The 4-pin RS-232/IR IN port allows IR control of the AT-OPUS-RX41.
Refer to the User Manual for more information.
1. Locate the required captive screw connector (included in the box).
2. Use wire strippers to remove a portion of the cable jacket.
3. Remove at least 3/16” (5 mm) of insulation from each of the wires.
4. Insert the wires into correct terminal. Refer to Figure 2.1, Figure 2.2, or Figure 2.3, below.
5. Connect the captive screw block to the proper port.
IR Control
OPTIONAL
RX TX TX RX
INPUT 4321 HDMI OUT DC 5VLAN
RX STX
RS-232 IR IN
OPTICAL
HDBaseT
RS-232 IR
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUSTM
Figure 2.1 - Wiring the 5-pin HDBaseT
RS-232/IR captive screw block to have a
controller at the viewing location send IR
commands over HDBaseT to an IR emitter
Figure 2.3 - Wiring the 4-pin HDBaseT RS-
232/IR IN captive screw block to control the
AT-OPUS-RX41 over IR.
Figure 2.2 - Wiring the 5-pin HDBaseT
RS-232/IR captive screw block to send IR
commands out over an IR emitter, from
a control system placed remotely at the
transmitter side.
TX
GND to control system
Sto control system
GND
RX
GND to IR emitter

7
Installation Guide
AT-OPUS-RX41
OPTIONAL
RX TX TX RX
INPUT 4321 HDMI OUT DC 5VLAN
RX STX
RS-232 IR IN
OPTICAL
HDBaseT
RS-232 IR
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUSTM
1. Connect up a category cable (CAT-5e or better) from the HDBaseT INPUT port to a
compatible HDBaseT transmitter.
2. Connect an HDMI cable from each of the HDMI INPUT ports to a UHD/HD source.
3. Connect an HDMI cable from the HDMI OUT port to a display device.
4. OPTIONAL: Connect a S/PDIF optical audio cable from the OPTICAL port to the TOSLINK
port of an audio output device.
5. OPTIONAL: Connect a control system to the HDBaseT RS-232 / IR port to control a
headend matrix (transmitter) or send/receive IR signals over HDBaseT. Refer to RS-232
Control (page 5) and IR Control (page 6) for wiring information.
6. OPTIONAL: Connect a control system to the RS-232 / IR IN port to control the AT-OPUS-
RX41. Both RS-232 and IR protocols are supported. Refer to RS-232 Control (page 5)
and IR Control (page 6) for wiring information.
7. Connect an Ethernet cable to the LAN port to control the AT-OPUS-RX41 using the built-in
web server or to control a sink device using pass-through IP control.
8. OPTIONAL: Connect the included 5 V DC power supply (Atlona part no. AT-PS-54-C)
to the DC 5V power receptacle. This step is only required if the AT-OPUS-RX41 will not be
powered by a compatible PoE transmitter.
Installation
1 3 4 5 6 7 82
Refer to the tables below for recommended cabling when using Altona products with HDBaseT
technology. The green bars indicate the signal quality when using each type of cable. Higher-
quality signals are represented by more bars. These tables are for guidance, only. Performance
may vary, based on environmental factors.
Cable Recommendation Guidelines
Core Shielding CAT5e CAT6 CAT6a CAT7
Solid UTP (unshielded) N/A
STP (sheilded)
Performance Rating (MHz) 350 500 600 800

8
Installation Guide
AT-OPUS-RX41
Web GUI
The AT-OPUS-RX41 includes a built-in web server, which allows easy management and control
of all features. Refer to the User Manual for routing and conguration information. Follow the
instructions below to access the web server.
1. Set the IP mode of the unit. Refer to the above instructions for more information.
2. Connect an Ethernet cable from the LAN port on the AT-OPUS-RX41, to the Local Area
Network (LAN).
3. Use an IP scanner to determine the IP address of the AT-OPUS-RX41.
4. Launch a web browser and enter the IP address of the unit.
5. The AT-OPUS-RX41 Login page will be displayed.
6. Enter the following information on the Login page.
Login: admin
Password: Atlona
7. Click the Login button.
For easy conguration of Atlona devices, AMS 2.0 is available from https://atlona.com/AMS for
free. Once AMS has been setup, following the instructions below.
1. Open a browser on the same network as AMS 2.0 and go to the IP of AMS 2.0. View the
AMS 2.0 installation instructions on how to nd the IP of the software, if necessary.
2. Enter the login information on the AMS 2.0 web page, then click the Login button.
3. View the AT-OPUS-RX41 manual for routing and conguration information.
AMS 2.0
IP Conguration
By default, the AT-OPUS-RX41 is set to DHCP mode, allowing a DHCP server (if present) to
assign the unit an IP address. To switch between DHCP and static IP mode, following the steps
below.
1. Make sure the unit is powered.
2. Press and hold the INPUT button for approximately 10 seconds.
3. Release the button once the POWER button begin to ash. The number of ashes will
indicate the currently selected IP mode. After the button stops ashing, the AT-OPUS-RX41
will be set to the selected IP mode.
POWER button ashes Description
Two Static IP mode IP address: 192.168.1.254
Subnet mask: 255.255.0.0
Gateway: 192.168.1.1
Four DHCP mode

9
Installation Guide
AT-OPUS-RX41
The AT-OPUS-RX41 includes two mounting
brackets, which can be used to attach the unit
to any at surface. Use the two enclosure
screws, on the sides of the unit to attach the
mounting brackets.
1. Using a small Phillips screwdriver, remove
the two screws from the left side of the
enclosure.
2. Position one of the mounting brackets, as
shown below, aligning the holes on the
side of the enclosure with one set of holes
on the mounting bracket.
3. Use the screws from Step 1 to attach the
mounting bracket.
4. Repeat steps 1 and 2 to attach the
second mounting bracket to the opposite
side of the unit.
5. Mount the unit to a at surface using the
oval-shaped holes, on each mounting
bracket. If using a drywall surface, a #6
drywall screw is recommended.
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUS
TM
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUS
TM
1 2 3 4
INPUT INPUTPOWER FW
AT-OPUS-RX41
OPUS
TM
NOTE: Mounting brackets can
also be inverted to mount the
unit under a table or other at
surface.
Mounting Instructions

10
Installation Guide
AT-OPUS-RX41
Notes

11
Installation Guide
AT-OPUS-RX41
Notes

12
Installation Guide
AT-OPUS-RX41
Version 2
© 2020 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Toll free US International
atlona.com •877.536.3976 •41.43.508.4321
English Declaration of Conformity
Chinese Declaration of Conformity 中国RoHS合格声明
The English version can be found under the resources tab at:
https://atlona.com/product/at-opus-rx41/.
由SKU列出於:
https://atlona.com/about-us/china-rohs/.
®
The terms HDMI, HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI licensing Administrator, Inc.