Panorama Antennas DMM-6-60 User manual

Installation
Instructions
Ultra Wideband 4G/5G MiMo Antenna
DMM-6-60
SW3-043 - v1.1

Installation Instructions
Contact Information
Content
3
EN
4-6
7

1. Introduction
4
The DMM antenna is a 2x2 MIMO (multiple input multiple output) / diversity capable accessory antenna
designed to improve reception for 2G / 3G/ 4G and some 5G modem devices.
2.1. Desk mounting
The DMM can mounted to any non-conductive surface using the supplied adhesive pad see fig. 2.
Ensure the area where you wish to mount the antenna is flat and level and free of grease and dirt. The
adhesive pad should be placed centrally and can be fitted on either side of the antenna by removing the
carrier film and pressing firmly. Once mounted to the antenna follow the same process to mount to the
mounting panel. For optimal pad adhesion the ambient temperature should be 10°C - 30°C (50°F -86°F).
2.2. Adhesive pad mounting
The DMM can be suction mounted to a window or other smooth surface utilising the supplied suction cup.
Simply screw the suction cup to the top most mounting position as shown in fig. 3. Proceed to mount the
antenna by pressing it firmly onto the desired surface until a firm grip is acheived. To dismount the
antenna hold the antenna firmly and unscrew the antenna from the suction cup. The suction cup can
then be removed from the mounting surface with ease.
2.3. Suction cup mounting
The DMM can be easily desk mounted using the integrated fold out feet as shown at fig. 1. Simply fold
out both feet and position the antenna as desired. The feet can then be re-stowed for transport.
2. Positioning the Antenna
The DMM is designed to operate with MIMO enabled modems which are able to take advantage of the
scattered signal paths which exist in everyday indoor environments. For this reason the user can be
very flexible about where they position the antenna. The antenna is omni-directional and does not need
to be facing any particular direction to operate. The antenna should not be positioned too close to metal
objects as this may affect performance.
2.4. Screw mounting
The antenna can be mounted to appropriate surfaces using the supplied self-tapping screws and wall
plugs as per fig. 4. Check for obstructions under the mounting panel and then drill appropriate holes using
the antenna as a template if required. Take care not to over-tighten screws when mounting as this may
break the mounting tabs- using the supplied spacers will help avoid over tightening.

Installing using screws
5
Installing using suction cups
3. Routing the cables
Route the dual coaxial cables from the antenna to the modem. The cables should not remain bunched
or tightly wound as this may affect performance.
1
3
2Installing using adhesive pad
4
Fold out desk stand feet

6
This accessory is guaranteed to be free from defects in the material and workmanship for 12 months
from the date of purchase. If your accessory is found to be faulty please return the product to Panorama
Antennas with proof of purchase. This warranty excludes normal wear and tear. This does not affect
your statutory rights.
THIS WARRANTY DOES NOT APPLY IN AUSTRALIA.
5. Important safety notes
RF Safety Note -Ensure that the antenna is mounted in such a way that no person is likely to be within
a distance of 30cms (12”) from the antenna during use. Ensure that the antenna is used only as supplied
the co-axial cables should not be cut shorter or otherwise modified.
General Safety Note - Make sure that the product is mounted so that it cannot fall and cause injury. Do
not chew the product or put it in your mouth. Do not leave children unsupervised with the product or
packaging.
Waste electrical products should not be disposed of with household waste. All electronic products with
the WEEE logo must be collected and sent to approved operators for safe disposal or recycling. Please
recycle where facilities exist. Many electrical/electronic equipment retailers facilitate “Distributor
Take-Back scheme”for household WEEE. Check with your Local Authority or electronic retailers for
designated collection facilities where WEEE can be disposed of for free.
RoHS 2 compliance is declared per Directive 2011/65/EU and its subsequent amendments with
exemption 6.c applied. This product contains lead as an alloying element in a copper alloy containing up
to 4% lead by weight.
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals, EC 1907/2006) This
product contains Lead (CAS No. 7439-92-1) which is classified as an SVHC (Substance of Very High
Concern) as being toxic to reproduction under Article 57c. of REACH.
Do not chew parts or put them in mouth, keep away from unsupervised children.
Dispose of parts as WEEE waste do not send to landll.
4. Warranty

Contact Information
7
Panorama Antennas Ltd
Panorama Antennas Inc
[e-mail]
61 Frogmore, Wandsworth, London, SW18 1HF
[phone]
USA
[email protected]om
[phone]
1551 Heritage Parkway, Suite 101, Mansfield, TX, 76063
Panorama Antennas Pty Ltd
Panorama Antennas SAS
Unit 1, 5 Jaggs Way, Kardinya, WA 6163
Australia
[phone]
[email protected]
France
[email protected]
[phone]
16 Allée des Acacias, 33700 Mérignac
Panorama Antennas Pte Ltd
Singapore
[email protected]
[phone]
Space@ Tampines, 18 Tampines Industrial Crescent, 528605
Panorama Antennas Ltd
Germany
[email protected]
[phone]