Panorama Antennas SW3-665 WMMG Original instructions

Ultra Wideband MiMo Antenna
Installaon Guide & Safety Informaon
Maximise your Connectivity, Minimise your Antennas

www.panorama-antennas.com
A.1
A.1 - Check that all the contents are in the box - This should include:
1 x Antenna 1 x U-Bolt 4 x Plain Washers
1 x Desk Stand 1 x U-Bolt Plate 4 x Spring Washers
2 x Wall Bracket Plates 4 x Screws 2 x Nuts
A.2 - Select Position
For a good installation the antenna should
be directed towards the strongest network
signal. In order to achieve this follow the
guide below.
1. Connect the antenna to your router
or modem with the antenna adapter (if
applicable) and coaxial cable provided.
2. Ensure that your device is connected
to the network and displaying the signal
strength indicator.
3. With the antenna at selected location, rotate it in approximately 45 degree steps – in
each position, you may need to wait for up to one minute to allow the signal strength
indicator to update.
Note: Signal strength indication may be displayed either:
a. Graphically with bars, (where more bars is a better signal), or
b. As a signal level value in dBm (e.g. -80) - in this case, the lower the negative number,
the better the signal, (i.e. -71 is stronger signal than -83).
A.2
SELECTING A POSITION
A.

EN
A.3. Mounting the Antenna
Mounting the antenna internally
To mount the antenna internally use the supplied desk stand and follow the instructions
at B. DESK MOUNTING INSTRUCTIONS
Mounting the antenna externally
Mounting the antenna outside will provide optimum signal strength and data rates.
Begin by following the instructions at A.1 & A.2 concerning position and orientating
the antenna. Then follow C. MAST MOUNTING INSTRUCTIONS or D. WALL MOUNTING
INSTRUCTIONS depending upon the equipment you have available.
IMPORTANT SAFETY INFORMATION
SELECTING A POSITION
A.
RF Safety Note – Ensure that the antenna is mounted in such a way that no person is likely to be
within a distance of 30cms (12”) from the antenna during use. Ensure that the antenna is used only
as supplied the co-axial cables should not be cut shorter or otherwise modied.
General Safety Note - Make sure that the product is mounted so that it cannot fall and cause
injury. Do not chew the product or put it in your mouth. Do not leave children unsupervised with the
product or packaging.
Waste electrical products should not be disposed of with household waste. All electronic products
with the WEEE logo must be collected and sent to approved operators for safe disposal or recy-
cling. Please recycle where facilities exist. Many electrical/electronic equipment retailers facilitate
“Distributor Take-Back scheme”for household WEEE. Check with your Local Authority or electronic
retailers for designated collection facilities where WEEE can be disposed of for free.
RoHS 2 compliance is declared per Directive 2011/65/EU and its subsequent amendments with
exemption 6.c applied. This product contains lead as an alloying element in a copper alloy contain-
ing up to 4% lead by weight.
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals, EC 1907/2006)
This product contains Lead (CAS No. 7439-92-1) which is classified as an SVHC (Substance of Very
High Concern) as being toxic to reproduction under Article 57c. of REACH. Do not chew parts
or put them in mouth, keep away from unsupervised children. Dispose of parts as WEEE
waste do not send to landll.
Electrical Caution - Parts of this antenna are an electrical conductor. Contact with power lines
can result in death or serious injury. The antenna and supporting mast must not be close to any
power lines during installation, use or removal. If the antenna is elevated and at risk from lightning
strike it must be ensured that the antenna is mounted and earthed appropriately by a trained
professional in accordance with the relevant standards.

www.panorama-antennas.com
B.1 B.2
1 - To Desk Mount this antenna you will need:
1 x Antenna 1 x Desk Stand
2 - Desk Mounting the antenna - Internal use only
Gently press the base of the antenna onto the desk stand ensuring that a ‘Click’
sound is made when the pegs are engaged. Store any excess cable safely out of the
way. Do not tightly wrap or bunch the cable.
DESK MOUNTING INSTRUCTIONS
B.

EN
C.1 C.2
1 - To Mast Mount this antenna you will need:
1 x Antenna 1 x U-Bolt 1 x U-Bolt Plate
2 x Washers 2 x Spring Washers 2 x Nuts
2 - Mast Mounting the antenna externally
Ensure that the selected mounting location can be safely accessed with the equipment
that you have available and mount the antenna so that it has at least 1 metre (3.3’) of
clearance from all obstructions if possible. The antenna should not be mounted directly
on to metal masts or poles. If the antenna must be mounted to such a surface it must
be mounted at the lip of the roof or the very top of the pole such that the body of the
antenna is elevated clear of the metal surface.
3 - Ensure a safe connection
Secure the antenna in place and waterproof the exposed connections. Fully tighten
the mounting hardware. If exposed the RF connector joint should be waterproofed with
a weatherproof electrical tape (self amalgamating type is recommended) allowing a
significant overlap of each turn and ensuring that the overlap is in the opposite direction
to predicted water fall.
C.3
MAST MOUNTING INSTRUCTIONS
C.