Panorama Antennas LPA-7-42 Series User manual

Installation Instructions
LPA[P]-7-42 Series
SW3-1029 - v1
1. Introduction
The LPA[P]-7-42 antenna series is a range of low profile, high performance SiSo IOT antennas covering 698-960/1427-4200MHz. Designed for situations
where a highly efficient antenna is needed the LPA[P]-7-42 can be installed on conductive or non-conductive surfaces.
The LPA-7-42 version can be wall or panel mounted via an adhesive pad and/or mounting screws or mast mounted using the supplied cable ties. The
LPAP-7-42 version is designed for panel mounting using the mounting bush on the base plate.
Both versions of the antenna are supplied with integral flame retardant RG174 cable (compliant to UN ECE R118), and are suitable for many installation
environments.
2. Mounting requirements and selecting location
The antenna can be mounted in a horizontal or vertical orientation. If the LPA-7-42 version is mounted vertically, the antenna cable exit should be orien-
tated facing downwards.
If utilising the adhesive pad it is recommended that the installation is carried out when the temperature is higher than 50°F (10°C) - the ideal temperature for
the pad bonding is in the range of 70°F (21°C) to 100°F (37°C).
For the panel mount version, or if using the mounting screw positions, ensure that there is adequate under panel clearance and that there are no objects
or obstructions under the panel where you need to drill. Measure to check for central position if applicable.
For optimal performance the antenna should, if possible, be mounted at least 300mm (1ft) away from other conductive objects on the mounting panel.
3. Panel mounting (LPAP-7-42 variant)
The LPAP-7-42 version can mount to panels 1-15mm (0.03-0.59”) thick via a
12mm (1/2”) mounting hole (Fig 1.) and to panels 15-25mm (0.69-1”) thick
via an 18mm (3/4”) hole (Fig 2.).
Mask panel area around hole position to protect the surface. Drill a pilot hole,
and then increase to 12mm (1/2”) or 18mm (3/4”), ensuring that drill/ cutter
bit does not contact any objects under the panel. Clean area around the
hole, carefully removing any swarf.
If also using the mounting screw positions then drill two additional pilot holes
to suit No.8 (4.2mm) screws. The antenna can be used as a drilling template.
Remove protective backing from underside of antenna and feed coaxial
cable through panel. Position the antenna over the hole and stick to panel
by applying firm downward pressure. Assemble top hat nut from underside in
correct orientation for mounting hole size and tighten.
If also using the mounting screw positions then make sure to position the
supplied sealing washers in the screw mount recesses before tightening the
screws. Do not over-tighten the screws as this may damage the antenna
housing.
Fig 1. Panel mounting to 1-15mm panel
Fig 2. Panel mounting to 15-25mm panel

4. Adhesive mounting (LPA-7-42 variant)
When using the screw positions (Fig 3.), drill two pilot holes to suit No.8
(4.2mm) screws. The antenna can be used as a drilling template.
Make sure that the selected mounting surface is clean and dry. De-
grease suface with 70% isopropyl alcohol (allowing time to dry) if
required. Remove protective backing from supplied adhesive pad and
adhere to underside of antenna, position the antenna over desired
location, remove remaining protective backing and stick to panel by
applying firm downward pressure.
If also using the mounting screws, ensure that the supplied sealing
washers are positioned in the hole recesses before inserting the screws.
Do not over-tighten the screws as this may damage the antenna hous-
ing.
7. Commission and test
●Check the VSWR measures as per specifications on relevant datasheet.
8. Notices
DO NOT
• operate the equipment in an explosive atmosphere.
• attempt to install the antennas without the proper safe equipment to access the install location.
• install the antenna in such a way that it may fall and cause injury.
• chew parts or put them in mouth, keep away from unsupervised children.
European Waste Electronic Equipment Directive 2002/96/EC
Waste electrical products should not be disposed of with household waste. All electronic products with the WEEE logo must be
collected and sent to approved operators for safe disposal or recycling. Please recycle where facilities exist. Many electrical/electronic
equipment retailers facilitate “Distributor Take-Back scheme”for household WEEE. Check with your Local Authority or electronic
retailers for designated collection facilities where WEEE can be disposed of for free.
Waiver: This document represents information compiled to the best of our present knowledge. It is not intended to as a representation or warranty of fitness of the products described for any particular pur-
pose. This document details guidelines for general information purposes only. Always seek specialist advice when planning installations and ensure that antennas are always installed by a properly qualified
installer in compliance with local laws and regulations.
6. Routing and terminating coaxial cables
Route the coaxial cable to the equipment, ensuring that the cable is se-
cured and protected from subsequent damage during access. The cable
should be routed observing the minimum bend radius of 13mm (1/2”).
If cable ties are used, they should not be overtightened, as this could
distort the cable profile and affect the antenna performance.
5. Pole / mast mounting (LPA-7-42 variant)
The antenna can be mounted to poles up to 25mm (1”) diameter using
the supplied cable ties (Fig 4.). First feed the cable ties through the slots
in the screw mounting recesses. Next position the antenna in the de-
sired location on the pole with the cable exiting downwards, engage and
pull the cable ties tight. It may be advisable to take additional measures
to ensure that the antenna cannot slide down the pole.
If alternative cable ties are used to secure the antenna, then please
ensure that they are made of UV resistant material.
Fig 3. Installing mounting screws
Fig 4. Pole mounting with cable ties