Paragon Pro Telpro The Troll 112 User manual

Model 112
53.5 In.
overall
height
28.5 - 51 In.
18 In. overall width
2 Inch shoe
Slide clamp will
handle a load
size from 28.5
to 51 inches.
The Troll® Panel Handler Model 112 makes light work of hustling drywall,
plywood and other heavy building panels around the work site. Its unigue
design locks the load vertically for easy mobility. Patented omni-directional
design makes fast, safe handling of building loads in tight quarters a snap.
The 250 lb. capacity hauls 4 sheets of half-inch board as well as large
banquet tables and solid core doors.
Position the Troll® in the middle of the
load with the SLIDE CLAMP up and
the LEG PIPE down. Lift one end of the
load and place it in the shoe of The
Troll®.
Move the SLIDE CLAMP down on the
SLIDE POLE to secure the load.
Hold the SLIDE CLAMP down with
one hand and use your other hand
to pull up on the SLIDE POLE. This
raises the stand.
Using the Troll® Model 112
SAVES YOUR BACK +
SPEEDS YOUR WORK =
MAKES YOU MONEY!
If you have questions about your Troll®
Model 112, please call us toll free at 1-
800-448-0222. We can also be reached
on the web at www.telproinc.com or by
mail at Telpro Inc., 7251 South 42nd
Street, Grand Forks, ND 58201. Thank
you for choosing the Troll®,
we hope you’re happy with
your purchase.
Step 1
Step 2
Step 3
Just tilt the Troll® back on the swivel
caster, pull it away from the wall and
you’re off. You can use this same tilting
action to position the Troll® for easy
off-loading when you reach your
destination.
Step 5
You’re now ready to roll.
Step 4
Form 42-12-00-00.07-10-02 © 2019 Paragon Pro Manufacturing Solutions All Rights Reserved.

Parts Breakdown
1. 45-00 UPRIGHT FRAME
2. 45-01 WHEEL BASE ASSEMBLY
(with fasteners)
3. 45-02 FLOOR PLATE(with fasteners)
4. 45-03 LEG PIPE
5. 45-04 SLIDE PIPE (with knob)
6. 45-05 SLIDE CLAMP (with fasteners)
7. 45-06 5” WHEEL (with fasteners)
8. 45-07 5” CASTER (with fasteners)
1
6
5
4
7
2
3
8
Attach the FLOOR PLATE to the
WHEEL BASE.
Fasten the wheeel base to the UP-
RIGHT FRAME using three 1/4” x 3/4”
bolts and 1/4” lock nuts. Finger tighten
only at this time.
Fasten the FLOOR PLATE to the
UPRIGHT FRAME using four 1/4” x 1/2”
bolts and 1/4” lock nuts. Inserting the
bolts will be easier if done in the order
shown. Tighten these bolts securely
using wrenches and do the same for
all other bolt assemblies that are still
only fi
nger tightened.
1st
2nd
2nd
Fasten the FLOOR PLATE to the
WHEEL BASE using two 1/4” x 3/4”
bolts and 1/4” lock nut. Inserting the
bolts will be easier if done in the order
shown. Finger tighten only at thie time.
1st
2nd
Attach the WHEEL BASE, aligning the
holes as shown.
Unpack box and check for assembly
components. (You will need two 7/16
wrenches)
1.UPRIGHT FRAME
2. WHEEL BASE
3. FLOOR PLATE
4. LEG PIPE
5. SLIDE PIPE with SLIDE CLAMP
ASSEMBLY
6. HARDWARE
(5) 1/4” x 1/2” (1 extra)
(6) 1/4” x 3/4” (1 extra)
(11) 1/4” locknut (2 extra)
4
5
3
2
1
6
Insert the SLIDE PIPE assembly into
the UPRIGHT FRAME with the KNOB
and CLAMP at the handle end of the
UPRIGHT FRAME.
Retract the LEG ASSEMBLY into the
UPRIGHT FRAME before proceeding to
the next step.
1ST
2ND
Begin by clipping
the LEG PIPE onto
the SLIDE PIPE in the
UPRIGHT FRAME assembly.
Clip the two pieces fully together and
slide the leg assembly fully into the
UPRIGHT FRAME.
the LEG PIPE onto
the SLIDE PIPE in the
3RD
4TH
5TH
6TH
7TH
8TH
9TH

Parts Breakdown
1. 45-00 UPRIGHT FRAME
2. 45-01 WHEEL BASE ASSEMBLY
(with fasteners)
3. 45-02 FLOOR PLATE(with fasteners)
4. 45-03 LEG PIPE
5. 45-04 SLIDE PIPE (with knob)
6. 45-05 SLIDE CLAMP (with fasteners)
7. 45-06 5” WHEEL (with fasteners)
8. 45-07 5” CASTER (with fasteners)
1
6
5
4
7
2
3
8
Attach the FLOOR PLATE to the
WHEEL BASE.
Fasten the wheeel base to the UP-
RIGHT FRAME using three 1/4” x 3/4”
bolts and 1/4” lock nuts. Finger tighten
only at this time.
Fasten the FLOOR PLATE to the
UPRIGHT FRAME using four 1/4” x 1/2”
bolts and 1/4” lock nuts. Inserting the
bolts will be easier if done in the order
shown. Tighten these bolts securely
using wrenches and do the same for
all other bolt assemblies that are still
only fi
nger tightened.
1st
2nd
2nd
Fasten the FLOOR PLATE to the
WHEEL BASE using two 1/4” x 3/4”
bolts and 1/4” lock nut. Inserting the
bolts will be easier if done in the order
shown. Finger tighten only at thie time.
1st
2nd
Attach the WHEEL BASE, aligning the
holes as shown.
Unpack box and check for assembly
components. (Yow will need two 7/16
wrenches)
1.UPRIGHT FRAME
2. WHEEL BASE
3. FLOOR PLATE
4. LEG PIPE
5. SLIDE PIPE with SLIDE CLAMP
ASSEMBLY
6. HARDWARE
(5) 1/4” x 1/2” (1 extra)
(6) 1/4” x 3/4” (1 extra)
(11) 1/4” locknut (2 extra)
4
5
3
2
1
6
Insert the SLIDE PIPE assembly into
the UPRIGHT FRAME with the KNOB
and CLAMP at the handle end of the
UPRIGHT FRAME.
Retract the LEG ASSEMBLY into the
UPRIGHT FRAME before proceeding to
the next step.
1ST
2ND
Begin by clipping
the LEG PIPE onto
the SLIDE PIPE in the
UPRIGHT FRAME assembly.
Clip the two pieces fully together and
slide the leg assembly fully into the
UPRIGHT FRAME.
the LEG PIPE onto
the SLIDE PIPE in the
3RD
4TH
5TH
6TH
7TH
8TH
9TH

Model 112
53.5 In.
overall
height
28.5 - 51 In.
18 In. overall width
2 Inch shoe
Slide clamp will
handle a load
size from 28.5
to 51 inches.
The Troll® Panel Handler Model 112 makes light work of hustling drywall,
plywood and other heavy building panels around the work site. Its unigue
design locks the load vertically for easy mobility. Patented omni-directional
design makes fast, safe handling of building loads in tight quarters a snap.
The 250 lb. capacity hauls 4 sheets of half-inch board as well as large
banquet tables and solid core doors.
Position the Troll® in the middle of the
load with the SLIDE CLAMP up and
the LEG PIPE down. Lift one end of the
load and place it in the shoe of The
Troll®.
Move the SLIDE CLAMP down on the
SLIDE POLE to secure the load.
Hold the SLIDE CLAMP down with
one hand and use your other hand
to pull up on the SLIDE POLE. This
raises the stand.
Using the Troll® Model 112
SAVES YOUR BACK +
SPEEDS YOUR WORK =
MAKES YOU MONEY!
If you have questions about your Troll®
Model 112, please call us toll free at 1-
800-448-0222. We can also be reached
on the web at www.telproinc.com or by
mail at Telpro Inc., 7251 South 42nd
Street, Grand Forks, ND 58201. Thank
you for choosing the Troll®,
we hope you’re happy with
your purchase.
Step 1
Step 2
Step 3
Just tilt the Troll® back on the swivel
caster, pull it away from the wall and
you’re off. You can use this same tilting
action to position the Troll® for easy
off-loading when you reach your
destination.
Step 5
You’re now ready to roll.
Step 4
Form 42-12-00-00.07-10-02 © 2002, Telpro Inc. All Rights Reserved

Chemical Hazard CAS# % By Weight
Arsenic Cancer 7440-38-2 Trace
Cadmium Develpmental 7440-43-9 Trace
Chromium Cancer, Developmental 7440-47-3 Trace
Ethylbenzene Cancer 100-41-4 Trace
Lead Cancer 7439-92-1 Trace
Methanol Developmental 67-56-1 Trace
Methylene Chloride (Dichloromethane) Cancer 75-09-2 Trace
Nickel Cancer 7440-02-0 Trace
Propylene glycol monobutyl ether Cancer 5131-66-8 Trace
Toluene Developmental 108-88-3 Trace
This product contains trace amounts of the following items which are known to cause
cancer and/or developmental harm in the state of California.
These chemicals are not hazardous under product's intended use.
Please review CAS# for more information.