Paramount Fitness FR1010-T-72H Quick start guide

FP-541 HB
FR1010-T-72H

15
16 19

Bolt (8*40mm)
Qty. 8
Hook
Qty.1
J
G
H
I
K
A
B
C
D
E
F
G
H
I
J
K
11
Protective Cover
2
Gas Tank Bracket
Gas Tank Support
1
1
LMO
PQR
Qty. 8
N
Bolt(6*20mm)
Washer

Bolt 6*20mm
G
ED
F
M
M
O
NOTE: It is best to use TWO PEOPLE for assembly of this gas
fire pit table.
Connect Side Panels (D,E,F,G) at top and bottom of each panel
with Bolt , Washer (M) as shown in Figure 1 using Allen Wrench.
NOTE: Do not over tighten all bolts.
H
N
N
N
O
M6
Connect Gas Tank Bracket (H) to the holes located at the bottom
of Side Panels (E,G) using 2 Bolts and Washer (N).
Then slide ends of Gas Tank Support (I) onto the right side of the
Gas Tank Bracket (H) and align the 2 holes on the front of the Gas
Tank Support (I) with the 2 holes in the Door Frame (F) and secure it
to the bottom piece of the Door Frame using 2 Bolts and Washer (N).
I

B
B
burner control knob
F
C
L
L
Attach the 4 Bolt(8*40mm) (L) to the corners of the Table Top (C).
Then align the Bolts with the holes in the Burner Bracket and
assembled panels and insert the Bolts through the holes. Secure the
Table Top to the Burner Bracket and assembled panels with
4 Washer,Spring Washer and Nuts (L).
Bolt 8*40mm
L
P
Q
4
4
Put the Burner (B) on the table top and the burner control knob
face the side panel (F)

K
J
5
6
Pour the Fire Glass (K) around the burner.
Be careful not to obstruct pilot light housing.
Put the Removable Burner Cover (A) on the burner when the fire
pit is not in use or after use when the fire pit has cooled.
When the fire pit has cooled completely, cover it with the
Protective Cover (J).
DO NOT PUT THE PROTECTIVE COVER ON A HOT FIRE PIT.
6

8
8
R
R
E
E

11
OPERATING INSTRUCTIONS
CAUTION
Do not attempt to operateuntil you
have read and understand all General
Safety Information in this manual and
all assembly is complete and leak
test has been performed.
BEFORE TURNINGGAS SUPPLY ON:
Your appliance was designed and
approved for outdoor use only.
Do NOT use it inside a building, garage, or any other enclosed area.
2. Make sure surrounding areas are free of combustible materials, gasoline, and
3. Ensure that there is no obstruction to air ventilation. Be sure all gas connections
are tight and there are no leaks.
4. Be sure the cylinder is clear of debris. Be sure any component removed during
assembly or servicing is replaced and fastened prior to starting.
1.
2.
BEFORE LIGHTING:
The appliance should be thoroughly inspected before each use, and by a qualified service person at least annually.
If relighting a hot appliance, always wait 5 minutes with tank valve closed.
Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. If the
hoseleaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by manufacturer.
DANGER!
FOR OUTDOOR USE ONLY
CARBON MONOXIDE HAZARD
Never use thisinside a house, or other
unventilated or enclosed areas. This appliance
consumes air (oxygen). Do not use in
unventilated or enclosed areas to avoid
endangering your life.
WHEN FIRE PIT IS ON:
Burner will display tongues of blue and
not be yellow or produce thick black
smoke, indicating an obstruction of
should be blue with straight yellow
tops. If excessive yellow flame is
detected, turn off fire pit and consult
the “Troubleshooting” section near the
end of this manual.
LIGHTING:
1. Turn the control knob to “OFF” position. (Figure A)
2. (Natrural Gas skip to Step 3) Fully open LP cylinder valve. Note: For initial start or after any cylinder change, hold
Control Knob IN for 2 minutes to purge air from gas lines before proceeding.
3. Push in gas control knob and turn counterclockwise to “HIGH” (Figure B). Press igniter button. If needed, return gas control
knob to “OFF” and repeat these steps until the fire pit lights (you should hear a clicking sound each time).
4. After the appliance lights, release control knob If you want a lower temperature push in the control knob and turn.
counterclockwise to the “LOW” Position (Figure C).
NOTE: If burner fails toremain lit, close all valves and wait at least 5 minutes for accumulated gas to dissipatebefore
attemptingto light.
OPERATING INSTRUCTIONS
WARNING
Very hot while in operation!
Do not touch Table Top or Burner
afteruse before placing Lid on Table Top
or touching any surfaces. Failure to comply
with these instructions may result in
serious bodily injury.
a
Electronic igniter
requires AAA battery
Standard igniter,
no battery required
NOTE：Some models have an Electronic
Igniter and will require installation of 1-AAA
battery.The battery should be installed by
unscrewing the RED IGNITER BUTTON.
CerugiF
Figure A Figure B
Contact us for assistance: cust[email protected] | [phone]

16

17

Contact us for assistance: [e-mail] | [phone] 18
GAS CONVERSION FROM LP TO NG
7. Connect NG hose to the burner control with a wrench. Connect the quick connect adapter to the NG supply
valve.
5. Reconnect the brass coupler on the stainless steel flex connector to the air shutter. Tighten using 2 wrenches.
6. Turn all knobs to OFF. Remove propane regulator and hose with brass adapter from the burner control
(manifold) with a wrench.
Propane Regulator
& Hose
Burner Control (Manifold)
Quick Connect Natural Gas (NG) Hose
(Not Included)
Quick Connect Natural Gas Adapter
(Not Included)
9. Fill out the conversion label included with your burner and apply it to the inside of the control panel
access door.
8. Place the burner back into the enclosure. Connect the NG hose to the Quick Connect adapter.
PART# NL-NGHOSE
www.paramountathome.com

19