Parker Healthcare ATOM V-808 Configuration guide

ATOM V-808
Cleaning Instructions
w w w . p a r k e r h e a l t h . c o m . a u
P a r k e r H e a l t h c a r e P t y L t d
Head Oce & International Department:
16 Redland Drive, MitchamVIC 3132 Australia
Ph: [phone] Fax: [phone]
Email: [e-mail] 2014 Rev. 1.

I M P O R T A N T
Please ensure
all steps of the
cleaning regime
are followed
after each use.

STEP 1 STEP 2 STEP 3
LINEN
Strip the linen from the
incubator and process
as per hospital protocol .
Open the head end
admiƩance panel
located on the leŌside
of the hood, draw out
the maƩress plaƞorm
toward you unƟl the
stopper is engaged.
To fully remove the
maƩress plaƞorm, press
the stopper to disengage
the lock and remove.
Wipe the maƩress
plaƞorm with a soŌcloth
moistened with hospital
grade detergent.
MATTRESS
PLATFORM
Remove the maƩress and
wipe over with a damp
cloth of warm water &
hospital grade detergent.
DO NOT fully emerse
maƩress in cleaning
soluƟon.
MaƩress
MaƩress
MaƩress
Page 1
Incubator
Incubator
Head End
Head End
Incubator
Head End
Mattress Platform
Mattress Platform
Mattress Platform
Stopper
Stopper
Position
Position
Stopper
Position
Stopper
Stopper
Stopper
PLEASE FOLLOW HOSPITAL PROTOCOL
FOR LINEN PROCESSING.

Remove the iris access
port cover.
Immerse and clean in a
hospital grade detergent.
Remove the rubber
packing from the snap-
open access ports.
Immerse and clean
in a
hospital grade
detergent.
Remove the rubber
packing from the
admiƩance panels.
Immerse and clean
in a
hospital grade
detergent.
TUBE INLET
Remove the packing
from the tube inlets.
(both sides of incubator)
Immerse and clean
in a
hospital grade
detergent.
AdmiƩance
AdmiƩance
panel packing
panel packing
AdmiƩance
panel packing
Tube inlet
Tube inlet
Tube inlet
Iris
Iris
Access
Access
Port
Port
Iris
Access
Port
SNAP-OPEN
ACCESS PORT
PACKING
ADMITTANCE
PANEL
PACKING
Snap-open Access
Snap-open Access
Panel Packing
Panel Packing
Snap-open Access
Panel Packing
ACCESS PORT
STEP 5 STEP 4STEP 6
Page 2

STEP 7 STEP 8
Page 3
1. Open the front
admiƩance panel.
Loosen the fixing screws
for each inside panel
(i.e. front, rear, top and
right) and remove the
inner panels.
2. Clean both sides of
each inside panel with
a soŌcloth moistened
with a hospital grade
detergent.
INSIDE PANEL
(FRONT, REAR,
TOP, RIGHT)
Front
Front
AdmiƩance
AdmiƩance
Panel
Panel
Front
AdmiƩance
Panel
Fixing Screws
Fixing Screws
Fixing Screws
Fixing Screw PosiƟons
Fixing Screw PosiƟons
Fixing Screw PosiƟons
REMOVING
THE LIGHT
Light release buƩons
Light release buƩons
Light release buƩons
Gently press the light
release buƩons on
both sides of the light
housing and liŌin an
upward direcƟon.

STEP 9
Page 4
REMOVING
THE HOOD
NOTE: THE FOLLOWING OPERATION
WILL REQUIRE TWO (2) PEOPLE.
1. Unclip the front metal
side clips (L & R) to
release the hood from
the base.
2. Pull the release screw
at the back of the hood
on both sides of the
incubator.
NOTE: Removal of the
hood will require two (2)
people to complete.
Using one person on
each side of the hood,
liŌup evenly and
parallel to the base
unƟl the hood has been
cleared from the
incubator body.
Place on a flat surface
and wipe over with a
soŌcloth dampended
with hospital grade
detergent.
1.
1.
Metal side clips
Metal side clips
(2 clips - L & R)
(2 clips - L & R)
2.
2.
Release screw
Release screw
(2 screws - L & R)
(2 screws - L & R)
1.
Metal side clips
(2 clips - L & R)
2.
Release screw
(2 screws - L & R)

STEP 10 STEP 11
Page 5
Fixing Screw
Fixing Screw
Fan
Fan
Fixing Screw
Fan
Middle Deck
Middle Deck
Middle Deck
Fan Cover
Fan Cover
Fan Cover
AŌer removal of the fan
cover, clean it with a soŌ
cloth moistened with a
hospital grade detergent.
To remove the fan, turn
the fixing screw clockwise.
Once the fixing screw
has been removed, use
2 hands to liŌthe fan.
Immerse and clean in a
hospital grade detergent.
Hold both sides of the
middle deck and liŌ.
Wipe over middle deck
plaƞorm with a soŌ
cloth moistened with
hospital grade detergent
Hold both sides of the
fan cover and liŌ.
FAN COVER
& FAN
REMOVAL
MIDDLE DECK
PLATFORM
Fan Cover
Fan Cover
Fan Cover

STEP 12STEP 13
Page 6
The condiƟoning chamber
will appear when all the
components menƟoned
previously have been
removed.
Clean thoroughly with a
soŌcloth moistened with
hospital grade detergent.
Ensure all parts are
completely dry before
undertaking re-assembly.
Re-assemble all removed
parts in the reverse order
of dis-assembly.
Check all parts are
aƩached correctly.
Once re-assembled and
checked, please ensure
the incubator is plugged
in, switched ON and the
incubator temperature is
set to 33 degrees.
Wipe the enƟre probe
(including thermostat)
with a soŌcloth
moistened with hospital
grade detergent between
use.
Thermostat
Thermostat
Thermostat
CondiƟoning
CondiƟoning
Chamber
Chamber
CondiƟoning
Chamber
SKIN
TEMPERATURE
PROBE
CONDITIONING
CHAMBER

This page is intentionally left blank.

w w w . p a r k e r h e a l t h . c o m . a u
P a r k e r H e a l t h c a r e P t y L t d
Head Oce & International Department:
16 Redland Drive, MitchamVIC 3132 Australia
Ph: [phone] Fax: [phone]
Email: [email protected]om.au
Distributed by: