Parsec Technologies ROTTWEILER User manual

ROTTWEILER
Installation Instructions
The Rottweiler antennas are high-performance, 5G,
CAT18 antennas, available with MIMO LTE, CBRS, Up to
3X WiFi, and GPS. The Doberman Series antennas are
perfect for mobile and xed wireless applications.
REQUIRED TOOLS
OPTIONAL ACCESSORIES
Hammer / Rubber Mallet
PTA0251 - 1 inch Star Lock Washer
Drill and 0.1in Drill Bit
PTA0346 – Heavy Duty Hardware Kit ( Nut, Lock Washer and Flat Washer)
PTA0339 – Gasket Adapter for 2020 Charger (Roof Mounting)
PTA0340 – Gasket Adapter for 2020 Explorer (Roof Mounting)
1 in Hole Saw
Phillips Screwdriver
SMA Wrench
Mounting Options
Step 1.
Step 2.
Select a mounting location where there is no obstructions within a radius of
24in. and is easily accessible.
Select one of the mounting options below, depending on your use.
- Roof Mount (Included)
Rottweiler antennas can be mounted on an automobile roof or any at
surface using the hardware provided with it.
- Magnetic Mount (Optional Part Number: PTA0330)
For temporary use. Doberman antennas can be mounted on any ferrous
metal surface using magnetic mount brackets.
- Pole Mount (Optional Part Number: PTA0149)
Antennas can be mounted on a pole with an optional bracket. For more
information on mounting, view the pole mount instructions listed on our website.

Roof Mount Instructions
Step 1.
Step 2.
Step 3.
After selecting the location to mount the Antenna, mask the mounting location to avoid paint damage. Mark the hole
center with ink or scribed cross hairs.
Use a center punch to make a dimple on the marked location to avoid drill bits from walking across the sheet metal.
Use a Twist drill of diameter about 0.1” and drill a pilot hole. Using a 1.0” diameter sheet metal hole saw, drill the hole.
The hole saw will cut the required diameter hole with less risk of stretching and distorting the vehicle surface. Clean up
any metal shavings from the hole cutting process. (Figure 1)
FIGURE 1
Preparing the Hole
Step 1.
Step 2.
Feed the coaxial cables from the antenna through the hole from the outside surface to the inside surface and thread
the entire length of the cable through the hole.
Clean debris off the vehicle surface and then mark the desired antenna orientation by placing the antenna at on the
vehicle surface.
Mounting the Antenna

Step 3.
Step 4.
Step 5.
Lift the antenna and remove the protective backing from the underside of the antenna and place the antenna back in
the desired position. Apply downward pressure on the antenna to stick it to the panel. This step is optional if you plan
on mounting the antenna magnetically.
To avoid the gap between the antenna and panel, it is reccomenended to use neutral cure silicon sealant around the
base of the mounting boot to fully compress the antenna to the mounting panel.
A split at washer and a split hex nut are provided in the kit for easy installation.
(Star washer is optional and not supplied. Part Number: PTA0251)
On the inside of the vehicle, thread the at washer over the cable, followed by star washer (if applicable) and then hex
nut. (Figure 2 & 3)
Slide the washers and nut to the threaded ange of the antenna and tighten the hex nut until antenna compresses at
with the surface of the vehicle.
(Figure 4)
FIGURE 3
FIGURE 4
FIGURE 2
Roof
Split Washer
Split Hex Nut
Step 1.
Step 2.
Route the cable from the antenna to the router by maintaining a minimum bend radius of 0.5in. Avoid sharp bends.
Run the cables adjacent to existing wiring.
Waterproof the RF connectors using electrical tape or a heat shrink tube, if required.
Routing the Cables

Step 1.
Step 2.
Step 3.
Choose a mounting location. The magnetic mount can be mounted on ferromagnetic metals like iron, steel, nickel etc
but not aluminum, copper etc.
Magnetic Mount Instructions (PTA0330)
Make sure the antenna is mounted at least 18 inches or as far as possible from the other roof mounted items like
antennas, light bars etc. to avoid any de-tuning or interference issues.
Make sure all of the magnets stick rmly to the base. If the surface is a curve adjust the magnets heights using washer.
Step 1.
Step 2.
Route the cable from the antenna to the router by maintaining a minimum bend radius of 0.5in. Avoid sharp bends.
Run the cables adjacent to existing wiring.
Waterproof the RF connectors using electrical tape or a heat shrink tube, if required.
Routing the Cables

Step 1.
Step 2.
Clean the connector such that there is no dust in the terminals.
Connect the cables from the antenna to the designated connector on the router as shown in the table below.
Cable Connection Instructions
LTE1 & LTE2
WIFI 1 & WIFI 2
WIFI 3
S.No CABLE FROM ANTENNA CONNECTOR ON ROUTER
1 LTE 1 MAIN0
2 LTE 2 AUX0
3 GPS GPS
4 WIFI 1 2.4/5GHz, LEFT GOLD
5 WIFI 2 2.4/5GHz, RIGHT GOLD
6 WIFI 3 5GHz, LEFT GOLD
For best MIMO performance use the following in pairs:
Commission and Testing
Check Coaxial Cables
Conrm Connection to Cellular Network
Check each coaxial cable connector and conrm it can’t be easily unscrewed with two ngers. Visually inspect coaxial
cable run for proper mechanical support.
Use a cellular device’s built in diagnostics to conrm t0he RSSI is better than -75dB. Conrm the cellular connection
supports communications at required data rates.
Connect the GPS / GNNS cable to the GPS / GNNS receiver and check for satelite acquisition.
Connect the Cellular / LTE & WLAN cables or stow unused pigtails.
Note: SMA connectors have a maximum torque of 3-5 inch lbs.
972-804-4600
Parsec Technologies
[email protected]
Last Revised: 3.9.2021