Parsec Technologies ST. BERNARD User manual

ST. BERNARD
Installation Instructions






REQUIRED TOOLS
REQUIRED ACCESSORIES (PRO9SB4L4WG-L OR PRO9SB4L4WG-A)
REQUIRED ACCESSORIES (PRO9SB4L4WG-G)
Router: CRADLEPOINT IBR1700-1200M
Router: CRADLEPOINT IBR1700-1200M
Battery: Chargetech 54k AC Battery Pack (OPTIONAL)
Ethernet Cords: 4pc (Length as required by the customer)(Not required for A version)
Ethernet Cords: 4pc (Length as required by the customer)
USB Cords - 1 pc (length as required by the customer)
Power Supply (required for router)
Power Supply (required for router)
Extension Cord (NEMA 5-15 Plug to NEMA 5-15 Socket)
Extension Cord (NEMA 5-15 Plug to NEMA 5-15 Socket)
Phillips Screwdriver
9” Zip Ties
Scissors

Router Installation:
Step 1.
Step 2.
Step 3.
Check the power options available on the case.
- For PRO9SB4L4WG-G: Install the battery on the top cover plate as directed in the “Router Power Options” step.
- For PRO9SB4L4WG-L or PRO9SB4L4WG-A: No Battery Option.
Install an activated SIM into the Router.
Thread the cables through the top cover plate. Make sure to not bend the cables when closing the box. (Figure 1)
FIGURE 1

Step 4.
Connect the Antenna cables to the router. Clean all connectors so there is no dust in the terminals. Follow the chart to
connect the cables. (Figures 2-4)
FIGURE 2
FIGURE 3
FIGURE 4

Step 5.
Step 6.
Choose the right AC power supply unit for the router and connect it to the router. (Figure 5)
Match the mount holes on the router to the mounting holes on the router mount base plate. Fasten the router to the
base using the four 1/4-20, 1/4 inch screws provided in the kit. (Figure 6)
FIGURE 6
FIGURE 5

Step 1.
Step 2. (PRO9SB4L4WG-G ONLY)
Step 3.
Choose four ethernet ports on the router that you are going to use the most. (LAN or WAN) Connect ethernet cords
from the four you require and connect them to the ports on the case. (It is recommended to choose 1 WAN and 2 LAN)
(Figure 7)
Connect the USB adapter on the case to the battery.
Connect the fan USB port on the case to the USB ports on the router. (Figure 8)
Router and Case connection Instructions:
FIGURE 7
FIGURE 8

Step 1.
Step 2.
Step 3.
PRO9SB4L4WG-G has the option of a battery.
Insert the battery in the battery tray. (Figure 9)
Place the top cover plate on the battery tray and fasten the battery tray to the top cover plate using nine 6-32, ¼” inch
Using the extension cord provided in the kit, connect the power supply unit of the router to the battery AC Port.
(Figure 11)
Parsec provides a battery tray for the Chargetech 54k Battery. To install the Chargetech 54k battery follow the
instructions below.
FIGURE 9 FIGURE 10
FIGURE 11
Router Power Options:

Step 4.
Step 5.
Connect the DC adapter installed on the case to the DC charging port on the battery. To charge the battery, use the
charger provided with the battery and connect the DC barrel plug on the charger to the case. (Figure 12 & 13)
battery. (Figure 14)
FIGURE 13
FIGURE 14
FIGURE 12

PRO9SB4L4WG-L and PRO9SB4L4WG-A comes with an AC adapter with 16-inch extension cord.
Router Power Options (Continued):
Parsec provides an AC adapter mounted on the case for L and G versions. For powering the router with the AC adapter
follow the instructions below.
Step 1.
Step 2.
Connect the AC adapter of the power supply unit to the AC adapter on the case.
Connect one end of the extension cord (NEMA 5-15 Plug to NEMA 5-15 Socket) to the case and the other end to the wall
to turn on the router. (Figure 15)
FIGURE 15

Antenna Operation:
Step 1.
Step 2.
Step 3.
Make sure all cables are properly connected. Check all of the connections and make sure there is no loose
connections.
Before turning on the antenna, always snap the fan and vent caps open. (Figure 16)
Turn on the power source of the router.
PRO9SB4L4WG-L and PRO9SB4L4WG-A: Plug in one end of the extension cord (NEMA 5-15 Plug to NEMA 5-15 Socket) to
the case and the other to the wall.
PRO9SB4L4WG-G: Turn on the main power switch of the battery and turn on the AC switch of the battery. (Figure 17)
FIGURE 16
FIGURE 17

Step 5.
Step 6.
Step 7.
Connect a network cable between the ethernet ports on a computer and one of the ethernet ports on the antenna
enclosure. Make sure you are connected to a LAN port and not a WAN port.
Bring up a web browser on the computer and type 192.168.0.1 into the address bar. You should see the Cradlepoint login.
(Figure 18)
Type the username and password. Username is “admin” by default. The password can be found on the information
cutout on the router. (Figure 19)
FIGURE 18
FIGURE 19