pass & seymour RW500U User manual

RW500U
PIR Occupancy Sensor Switch
with Manual
ON/OFF
Limited FIVE YEAR Warranty
Pass & Seymour/Legrand will remedy any defect in workmanship or material in Pass & Seymour/Legrand prod-
ucts which may develop under proper and normal use within five years from the date of purchase by a consumer:
(1) by repair or replacement, or, at Pass & Seymour/Legrand’s option, (2) by return of an amount equal to the
consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Pass & Seymour/Legrand
does not include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELE-
MENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED
OR IMPLIED WARRANTIES including warranties OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-
POSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimer or exclusion or limitation of incidental or
consequential damages, so the above disclaimers and limitation or exclusion may not apply to you.) ANY IMPLIED
WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTIC-
ULAR PURPOSE SHALL BE LIMITED TO THE FIVE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply to you.)
To ensure safety, all repairs to Pass & Seymour/Legrand products must be made by Pass & Seymour/Legrand
or under its specific direction. Procedure to obtain performance of any warranty obligation is as follows:
(1) Contact Pass & Seymour/Legrand, P.O. Box 4822, Syracuse, NY 13221 for instructions concerning return
or repair; (2) return the product to Pass & Seymour/Legrand, postage paid, with your name and address and a
written description of the installation or use of the Pass & Seymour/Legrand product, and the observed defects
or failure to operate, or other claimed basis for dissatisfaction.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Please read all instructions before installing
Installation Instructions
Lens
Lighted Switch
ON/OFF Button
Syracuse, NY 13221
SPECIFICATIONS
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120VAC, 60Hz
Load (Single Pole Circuit)
Incandescent . . . . . . . . . . . . . . . . . . . . . . . . . . 25-500 Watts
Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 minutes
Environment . . . . . . . . . . . . . . . . .Residential Indoor use only
Operating Temperature . . . . . . . .32° to 131°F (0° to 55°C)
Humidity . . . . . . . . . . . . . . . . . . . .95% RH, non-condensing
Electrical Supply Wire . . .minimum temp rating 167°F (75°C)
Tools Needed:
Insulated Screwdriver
Wire Strippers
P.O. Box 4822, Syracuse, NY 13221-4822
Technical Support: 800.223.4185 • www.passandseymour.com
340800 Rev. B 08129
Visit our website at: www.passandseymour.com
TEST MODE
To test the detection coverage:
During the TEST mode, the controlled load turns ON for 5 seconds each time the
sensor detects occupancy.
1. Press and hold the ON/OFF button. After 10 seconds the lighted switch turns
OFF. The controlled load turns ON if it was not already ON. The sensor is now
in a TEST mode that lasts 5 minutes. (You can end the TEST mode sooner by
pressing the ON/OFF button for another 10 seconds).
2. Move out of the coverage area or stand very still. The controlled load turns
OFF after 5 seconds if no motion is detected.
3. Move into the coverage area. The controlled load turns ON for 5 seconds each
time the sensor detects motion. After 5 seconds expire without motion
detection, the load turns OFF. The controlled load turns ON automatically with
the next motion detection and stays ON for 5 seconds.
4. Repeat as necessary to ensure that the desired coverage areas are within
detection range.
TROUBLESHOOTING
Load will not turn ON (lighted switch is visible):
• Move in front of the sensor to automatically turn lights ON. If lights do not
turn ON, press the ON/OFF button. The lighted switch should turn OFF and
the controlled load should turn ON, if not:
• Check the light bulb.
• Turn OFF power to the circuit then check wire connections.
• Remember that if the load is turned OFF manually, Automatic-ON is
reenabled only after no motion is detected for 5 minutes.
Light will not turn ON (lighted switch is NOT visible):
• Check the light bulb.
• Make certain that the circuit breaker is ON and functioning.
• Turn OFF power to the circuit then check wire connections.
Load will not turn OFF:
The time delay is 5 minutes (fixed time delay).
• Make sure no motion occurs in the coverage area until the time delay
expires.
• If the load does not turn OFF, call Technical Support at 800.223.4185.
• Hot air currents and heat radiant devices can cause false detection. Make
sure the sensor is at least 6 feet (2 meters) away from devices that are a
significant heat source (e.g heater, heater vent, high wattage light bulb).
• Press the ON/OFF button. If the controlled load does not turn OFF, turn
OFF the power to the circuit, then check wire connections.
340800_RevB_IS_12266 4/23/07 9:55 AM Page 1

1. Prepare the switch box.
After the power is turned OFF at the circuit
breaker box, remove the existing wall plate and
mounting screws. Pull the old switch out from
the wall box.
2. Identify the type of circuit.
In a Single Pole Circuit (see Fig. 2), two single
wires connect to two screws on the existing
switch. A ground wire may also be present
and connected to a ground terminal on the
old switch.
CAUTION – FOR YOUR SAFETY: Connecting a proper ground to the
sensor provides protection againstelectrical shock in the event of
certain fault conditions. If a proper ground is not available, consult
with a qualified electrician before continuing installation.
Onlyconnect the RW500U to a Single Pole Circuit. The RW500U is not
suitable for 3-way switching. If the existing wiring does not match the
description for a Single Pole Circuit, you should consult with a qualified
electrician. If 3-way switching is required, use P&S 3-way occupancy
sensor, RW3U600.
3. Prepare the wires.
Tag the wires connected to the existing switch, so that
they can be identified later. Disconnect the wires. Make
sure the insulation is stripped off the wires to expose
their copper cores to the length indicated by the “Strip
Gage” (in Fig. 3) (approx. 1/2 inch).
DESCRIPTION AND OPERATION
The RW500U Occupancy Sensor Switch is designed to replace a residential light
switch. It is ideal for laundry rooms, utility rooms, storage areas, closets and any
other indoor area in a residential building where occupancy sensor-based
automatic ON/OFF controls are desirable. The sensor requires no adjustments to
operate successfully in those particular applications for which it was designed.
Lighted Switch
To help you locate the RW500U in a dark room, a green LED illuminates the
ON/OFF button while the controlled light (load) is OFF. When the load is ON,
the LED is OFF.
Push Button
The push button can be used to manually turn ON and OFF the load. To turn
the load OFF, tap firmly on the push button once. The lighted switch will turn ON
and the load will turn OFF. If the load is turned OFF manually, Automatic-ON is
reenabled when no motion is detected for 5 minutes.
Time Delay
The RW500U has a fixed time delay of 5 minutes. Lights will remain ON for
5 minutes after the last motion detection.
Coverage Area
The RW500U has a maximum range of
180 degrees and a coverage area of
600 sq. feet (56 sq, meters). The sensor must
have a clear and unobstructed view of the
coverage area. Objects blocking the sensor’s
lens may prevent detection thereby causing
the light to turn OFF even though someone
is in the area.
Windows, glass doors, and other transparent barriers will obstruct the
sensor’s view and prevent detection.
WARNING
Disconnect power to the wall switch box by turning OFF the circuit
breaker or removing the fuse for the circuit before installing the
RW500U, replacing lamps, or doing any electrical work.
INSTALLATION & WIRING
Fig 2: Typical Single Pole
Switch Wiring
Fig 3: Wire Stripping
Visit our website at: www.passandseymour.com Call 800.223.4185 for Technical Support
25'
(7.6m)
12'
(3.7m)
Fig. 1: Sensor Coverage Area
4. Wire the sensor.
Twist the existing wires
together with the wire leads on
the RW500U sensor as
indicated below. Cap them
securely using the wire nuts
provided (see Fig 4).
• Connect the green or non-
insulated (copper) GROUND
wire from the circuit to the
green wire on the RW500U.
• Connect the power wire from
the circuit box (HOT) to the
black wire on the RW500U.
• Connect the wire to the lamp
(LOAD) to the red wire on the
RW500U.
5. Put the RW500U in the
wall box.
Position the lens above the
ON/OFF button (lens at top,
button at bottom) and secure it to
the wall box with the screws provided.
6. Attach the new cover plate.
Secure it to the wall box with the
screws provided.
7. Restore power to the circuit.
Turn ON the breaker or replace the fuse.
8. Test the sensor’s operation.
See TEST MODE.
Initial Power-up Delay
There is an initial warm-up
period the first time power is
applied to the unit and after
a power failure lasting more
than 5 minutes. It may take
up to 1 minute before the
lights turn ON. However, the
lights can be turned ON/OFF
manually by pressing the
ON/OFF button at any time
when power is supplied to
the unit.
Fig. 4: Sensor orientation, wire connections
and wall box assembly
340800_RevB_IS_12266 4/23/07 9:55 AM Page 4

REV. DESCRIPTION INT: REV. DATE APPROVED
1 340800 JAR
•Print: 2-sided
• Ink Color: Black
•Paper: White 16lb (60g/m sq)
• Final trim size: 12" (Wide) x 6" (High).
• Three (3) fold.
• Final folded size: 4" (Wide) x 6" (High).
TITLE BOX PAGE ONLY.
DO NOT MAKE FILM • DO NOT PRINT
SYRACUSE, NEW YORK
Title: RW500U Installation Instructions
IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE
ADDITIONAL FILE FORMATTING, PLEASE CONTACT Joyce Rougeau.
Phone: [phone]
Email: [email protected]om
Drawing #:
08129
Orig. Drawing Date: 28 FEB 06 Rev. #:
1
Revision Date: 28 FEB 07
ROUGEAU
Scale: 1:1
All information in this drawing is the property of P&S/Legrand and cannot be copied or used
without the written approval of P&S/Legrand.
Drawn by
PLM
MarCom
Engineering
QA
TITLE BOX PG
340800_RevB_IS_12266 4/23/07 9:55 AM Page 7