PATIOJOY GYM06499 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Please give us a chance to make it right and do better！
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP!
USER’S MANUAL
4 Pcs Wicker Sofa Set
FLOOR AREA
2MX2M
ASSEMBLED BY 2 ADULTS
GYM06499

Contact Us!
Hardware inside
Do NOT return this item.
Contact our friendly customer service department for help first.
E-mail
Before You Start
Read each step carefully before starting. It is very important to ensure each step followed in
correct order, otherwise assembly difficulties may occur.
Most of board parts are labeled or stamped on the raw edges. Have a check to make sure all
parts are included.
Work in a spacious area, preferably on a carpet close to where the unit will be used.
Keep the handtools close at hand. Do not use power tools to assemble your furniture.
They may scratch or damage the parts.
02
[email protected]

Not actual size
Left Arm x 2 Right Arm x 2
Back x 2
Cushion x 2
Seat x 2
03

Not actual size
04

Hardware List
Actual size
I4
M6 x 15mm
BOLT
BOLT
J4
M6 x 25mm
BOLT
M6 x 35mm
K12
O8
ADJUSTABLE
LEVELLERS
M20
M6
WASHER
N1
4 x 4
ALLEN WRENCH
05

STEP 1
Insert adjustable levellers (O) to boom of each
Arm(A) by turning clockwise unl secure.
Adjust height as desired.
Repeat step for the other side arm(B).
06

STEP 2
(K & J) with washers (M) through the pre-drilled holes
Aach the seat(D) to the arm (B) by inserng bolts
on the seat into the pre-welded nuts on the arm.
Repeat step for the other side arm(A).
07
assembly is completed.

Aached the back(C) to the seat (D) by inserng
bolts (K) with washers (M).
Aached the back(C) to the arm (A&B) by inserng
bolts (I) with washers (M).
STEP 3
STEP 4
08

Tighten all the bolts with the allen wrench,
and turn the chair to the upright posion.
place the seat cushions(P) onto the chair seat.
Your chair is now ready for use.
STEP 5
09

Maximum Loads
250 lbs
This item is only suitable within the specified maximum load-bearing. Heavier loads than
the indicated load capacity may cause instability, resulting in possible injuries.
10

Not actual size
Left Arm x 1 Right Arm x 1
Back x 1
Cushion x 1
Seat x 1
11

Not actual size
12

Hardware List
Actual size
I2
M6 x 15mm
BOLT
BOLT
J2
M6 x 25mm
BOLT
M6 x 35mm
K7
O4
ADJUSTABLE
LEVELLERS
M11
M6
WASHER
N1
4 x 4
ALLEN WRENCH
13

STEP 1
Insert adjustable levellers (O) to boom of each
Arm(A) by turning clockwise unl secure.
Adjust height as desired.
Repeat step for the other side arm(B).
14

STEP 2
(K & J) with washers (M) through the pre-drilled holes
Aach the seat(F) to the arm (B) by inserng bolts
on the seat into the pre-welded nuts on the arm.
Repeat step for the other side arm(A).
15
assembly is completed.

Aached the back(E) to the seat (F) by inserng
bolts (K) with washers (M).
Aached the back(E) to the arm (A&B) by inserng
bolts (I) with washers (M).
STEP 3
STEP 4
16

Tighten all the bolts with the allen wrench,
and turn the chair to the upright posion.
place the seat cushions(Q) onto the chair seat.
Your chair is now ready for use.
STEP 5
17

Maximum Loads
250 lbs 250 lbs
This item is only suitable within the specified maximum load-bearing. Heavier loads than
the indicated load capacity may cause instability, resulting in possible injuries.
18

Not actual size
Table Top x 1
Table Leg x 2
19

Not actual size
20