Patton electronics 2156 User manual

L
AN extension doesn’t have to be expen-
sive or difficult. Patton’s Model 2156 and
Model 2157 Series of auto-rate Ethernet
Extenders open the door to low-cost and easy
set-up LAN extension. The LAN Extenders are
easy to use and take advantage of existing
copper twisted-pair infrastructure to connect
LANs at high speed and over long distances.
The Model 2156 can connect at speeds up to
2.3 Mbps with distances ranging from 5.3 to
9.4 km (3.3 to 5.8 miles) on standard 0.5 mm
(24 AWG) voice-grade twisted pair. The
Model 2157 can connect at speeds up to 4.6
Mbps over distances ranging from 3.3 to 9.4
km (2.1 to 5.8 miles) on standard 0.5 mm
(24 AWG) voice-grade twisted pair.
Whether connecting corporate LANs or
remote offices, Patton Ethernet Extenders
offer the best combination of speed and dis-
tance in the industry. Other LAN extenders
operate at a single rate or are difficult to con-
figure for LANs located at different distances,
but the CopperLink Ethernet Extenders’ auto-
rate adaptation feature ensures that users get
the highest speed possible for the distances
they are trying to reach. Patton Ethernet
Extenders come with a built-in MDI-X switch,
which simplifies connection to LANs or PCs
since it works correctly with a straight-
through cable or a cross-over cable. Set-up is
easy, just connect the Ethernet port cable and
the copper twisted-pair to the Extenders, then
apply power! Patton CopperLink Auto-rate
Ethernet Extenders are the perfect fit for cost-
effective simple and efficient LAN extension!
Visit www.patton.com for more information.
Reach your remote LAN with Patton’s Auto-Rate Ethernet Extenders and get the best speed/distance combination in
the industry using just a single twisted-pair.
CopperLink™
Ethernet Extender
Patton Models 2156 & 2157
Extenders
High Speed Extension
With the Model 2157 you get speeds up to 4.6
Mbps, while the Model 2156 delivers speeds up
to 2.3 Mbps
CopperLink 2-Wire Connection
Easy 2-wire CopperLink connection via built-in
RJ-11 port
Auto-sensing Ethernet
Auto 10 or 100Base-T and full or
half-duplex Ethernet operational
Auto-rate Selection
Just plug the units in, and they will determine the
maximum rate possible for the connection
Transparent LAN Bridging
Passes higher layer protocols and
supports 802.1Q VLAN tagging
Automatic Learning, Aging, and
Filtering
Only allows packets with addresses outside
the LAN to be forwarded
Auto-sensing 10
or 100Base-T,
and full or half-duplex
Front panel indicators
show operational
status at a glance
AC or DC
power options
Only a single twisted
pair needed for speeds
up to 4.6 Mbps
Proven
Patton design
Built-in MDI-X
cross-over switch
Patton Model 2157

7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
Phone [phone]
Fax [phone]
E-mail [email protected]
Web www.patton.com
07M2157-2156-DS2
Meriedweg 7
CH-3172 Niederwangen
Phone [phone]
Fax [phone]
E-mail [email protected]
Web www.inalp.com
Patton is a registered trademark, and is a trademark of Patton Electronics Company
in the United States and other countries.
Specifications
Competitive Positioning
CopperLink Line Interface
RJ-45 (pin 4 = ring; pin 5 = tip)
Ethernet Interface
8-position shielded RJ-45. Auto-sensing 10/100Base-T
with half or full-duplex operation. DIP switch capable of
disabling 100-Mbps full-duplex for equipment that does
not support 802.3X (Pause Packets)
Protocol
Transparent to high layer protocol. Supports 802.1Q
VLAN tagging
Modulation
(Quadrature Amplitude Modulation) QAM 4-band
Duplexing Method
FDD (Frequency Division Duplexing)
Frequency Range
CopperLink: 0–12 MHz
Transmission
CopperLink line rate: Up to 50 Mbps
Surge Suppression
CopperLink line maximum current surge: 20kA (8/20µs)
gas tube
Front Panel Indicators
Power, Link, Ethernet
Dimensions
1.5H x 4.13W x 3.75D in. (3.81H x 10.5W x 9.53D cm)
Weight
0.4 lbs (0.18 kg) without power supply
Power
External AC and DC options: 120VAC, and universal
input (UI)—100–240 VAC, or optional -48 VDC, -24
VDC, or -12 VDC
Environment
Temperature: 32–122°F ( 0–50°C)
Humidity: Up to 90% non-condensing
Compliance
FCC Part 15A, CE Mark, EMC Directive 89/336/EEC,
Low-Voltage Directive 73/23/EEC
Patton’s CopperLink Auto-Rate Ethernet Extenders
are the perfect fit for simple, cost-effective high
speed Ethernet Extension. They allow customers to
take advantage of the existing copper infrastructure
to connect remote LAN’s across distances and at
speeds previously unthought-of. The auto-rate fea-
ture ensures the highest speed is achieved on each
connection, and the plug-n-play operation ensures
they are up and running in seconds. Add in the
auto-sensing full/half duplex 10/100Base-T
Ethernet port and the integrated crossover switch
to make setup even easier, and the value of these
Ethernet Extenders can’t be beat!
• Auto-Rate Feature
The advanced auto-rate algorithm automatically
determines the best possible rate for each connec
tion and sets up each extender without any need for
user interface.
• Plug-and-Play
Just unpack the extenders, plug them into each end
of the extension, power them up, and they are up
and running. It doesn’t get any easier!
• High Speed/Long Reach
These Ethernet Extenders provide the best combi-
nation of speed and distance seen anywhere in the
industry !
The Auto-rate feature ensures
that the best combination of
speed and distance is achieved
for each LAN extension
Twisted Pair
Model 2157
Model 2157
Model 2157
Twisted
Pair
Application Example—Corporate Campus LAN Extension