Patton electronics 12168 User manual

USER
MANUAL
MODEL 1068
Variable Rate
VLINK Modem
SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
Part# 07M1068-A
Doc# 058111UA
Revised 6/10/02
An ISO-9001Certified
Company

2
CONTENTS
1.0 Warranty Information ................................................................. 4
1.1 Radio and TV Interference............................................................ 4
1.2 CE Notice...................................................................................... 4
1.3 FCC Part 68 (1068DV Only)......................................................... 5
1.4 Industry Canada Notice................................................................ 6
1.5 Service.......................................................................................... 6
2.0 General Information.................................................................... 7
2.1 Features........................................................................................ 7
2.2 Description.................................................................................... 7
3.0 Installation................................................................................... 9
3.1 Standalone unit installation........................................................... 9
3.2 Rack card installation.................................................................. 10
3.3 Connecting the Twisted-Pair Line Interface................................ 11
3.4 Connecting the 10/100Base-T Ethernet Interface ...................... 12
Connecting the 10/100Base-T Ethernet Port to a Hub............... 13
Connecting the 10/100Base-T Ethernet Port to a PC (DTE)...... 13
3.5 Connecting the POTS/ISDN line................................................. 13
3.6 Connecting Power ...................................................................... 14
4.0 Configuration ............................................................................ 15
4.1 Configuring the hardware DIP switches...................................... 15
4.2 Configuring DIP Switch S1 ......................................................... 17
Switch S1-1: Ethernet Auto Sense............................................. 17
Switches S1-2 and S1-4: Data Rate........................................... 17
5.0 Operation................................................................................... 19
5.1 Power Up.................................................................................... 19
5.2 Front Panel LED Status Monitors............................................... 19
ASpecifications ........................................................................... 21
A.1 LAN Connection .......................................................................... 21
A.2 Transmission Line ....................................................................... 21
A.3 VDSL Line Rate ........................................................................... 21
A.4 VDSL Distance ............................................................................ 21
A.5 VDSL Surge Suppressor ............................................................. 21
A.6 LED Status Indicators ................................................................. 21
A.7 Power Supply .............................................................................. 21
A.8 Temperature Range .................................................................... 21
A.9 Humidity ...................................................................................... 21
A.10 Dimensions ................................................................................. 21
B Model 1068 Series Factory
Replacement Parts and Accessories...................................... 22
C Model 1068 Series Interface Pin Assignment ........................ 23
C.1 10/100Base-T Interface .............................................................. 23
RJ-45.......................................................................................... 23

3
C.2 VDSL Interface ............................................................................ 23
RJ-45.......................................................................................... 23
Terminal Block............................................................................ 23
C.3 POTS/ISDN Interface .................................................................. 23
RJ-45.......................................................................................... 23
D DISTANCE CHART, BASED ON 24 AWG (0.5 MM)................. 24

4
1.0 WARRANTY INFORMATION
Patton Electronics warrants all Model 1068 components to be free from
defects, and will—at our option—repair or replace the product should it
fail within one year from the first date of the shipment.
This warranty is limited to defects in workmanship or materials, and does
not cover customer damage, abuse or unauthorized modification.If this
product fails or does not performs as warranted, your sole recourse shall
be repair or replacement as described above.Under no condition shall
Patton Electronics be liable for any damages incurred by the use of this
product.These damages include, but are not limited to, the following:lost
profits, lost savings and incidental or consequential damages arising
from the use of or inability to use this product. Patton Electronics spe-
cifically disclaims all other warranties, expressed or implied, and the
installation or use of this product shall be deemed an acceptance of
these terms by the user.
Note Conformity documents of all Patton products can be viewed
online at www.patton.com under the appropriate product page.
1.1 RADIO AND TV INTERFERENCE
The Model 1068 generates and uses radio frequency energy, and if not
installed and used properly-that is, in strict accordance with the manufac-
turer’s instructions-may cause interference to radio and television recep-
tion.The Model 1068 has been tested and found to comply with the limits
for a Class A computing device in accordance with specifications in Sub-
part B of Part 15 of FCC rules, which are designed to provide reasonable
protection from such interference in a commercial installation. However,
there is no guarantee that interference will not occur in a particular instal-
lation. If the Model 1068 does cause interference to radio or television
reception, which can be determined by disconnecting the unit, the user is
encouraged to try to correct the interference by one or more of the follow-
ing measures: moving the computing equipment away from the receiver,
re-orienting the receiving antenna and/or plugging the receiving equip-
ment into a different AC outlet (such that the computing equipment and
receiver are on different branches).
1.2 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates that it is
in compliance with the Electromagnetic Compatibility (EMC) directive
and the Low Voltage Directive (LVD) of the European Union (EU). A Cer-
tificate of Compliance is available by contacting Technical Support.

5
1.3 FCC PART 68 (1068DV ONLY)
This equipment complies with Part 68 of the FCC Rules.Please note the
following:
1. You are required to request service from the telephone company
before you connect the Model 1068DV to a network.When you
request service, you must provide the telephone company with the
following data.
— The required Universal Service Order code (USOC)
jack: RJ-11C
— The make, model number, Ringer Equivalence Number (REN),
and FCC Registration number of the Model 1068DV.
The REN helps you determine the number of devices you can con-
nect to your telephone line and still have all of those devices ring
when your number is called. In most, but not all, areas, the sum of
the RENs of all devices should not exceed five (5.0).To be certain of
the number of devices you can connect to your line, you should call
your local telephone company to determine the maximum REN.
— The Facility Interface Code: 02LS2
— The Service Order Code(s) (SOC): 9.0F
— REN No.: 0.2
2. Your telephone company may make changes to its facilities, equip-
ment, operations, or procedures that could affect the proper func-
tioning of your equipment.The telephone company will notify in
advance of such changes to give you an opportunity to maintain
uninterrupted telephone service.
Caution
The Model 1068D is not intended to be connected to the
public telephone network.
Caution
The VLINK port is not intended to be connected to the
public telephone network. The 1068DV contains a
POTS/ISDN connection that can be connected to the
public telephone network.

6
3. If your Model 1068DV causes harm to the telephone network, the
telephone company may temporarily discontinue your service. If
possible, they will notify you in advance, but if advance notice is not
practical, you will be notified as soon as possible and will be
informed of your right to file a complaint with the FCC.
4. If you experience trouble with the Model 1068DV, please contact
Patton Electronics Company for service or repairs.Repairs should
be performed only by Patton Electronics Co.
5. You are required to notify the telephone company when you discon-
nect the Model 1068DV from the network.
1.4 INDUSTRY CANADA NOTICE
NOTICE:This equipment meets the applicable Industry CanadaTerminal
Equipment Technical Specifications.This is confirmed by the registration
number.The abbreviation, IC, before the registration number signifies
that registration was performed based on a Declaration of conformity
indicating that Industry Canada technical specifications were met.It does
not imply that Industry Canada approved the equipment.
1.5 SERVICE
All warranty and non-warranty repairs must be returned freight prepaid
and insured to Patton Electronics. All returns must have a Return Materi-
als Authorization number on the outside of the shipping container.This
number may be obtained from Patton Electronics Technical Services at:
• Tel: [phone]
• Email: [email protected]
• URL: http://www.patton.com
Note Packages received without an RMA number will not be
accepted.

7
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product.This
product has been thoroughly inspected and tested and is warranted for
one year for parts and labor. If any questions or problems arise during
installation or use of this product, contact Patton Electronics Technical
Support at [phone].
2.1 FEATURES
• Easy to install standalone VLINK modems— no configuration required
• Auto-sensing full or half-duplex Ethernet
• Auto-sensing 10/100Base-T
• Extends network connections up to 6,652 ft (2.03 km) over 2-wire 24-
AWG unconditioned lines
• Switch selectable line rates up to 16.67 Mbps
• 7 symmetric or asymmetric settings via DIP switch
• POTS/ISDN splitter on board
• Transparent operation
• LED indicators for Power, Ethernet Link & Activity,VLINK & Quality of Line
(QOL)
• Surge suppression up to 20 kA (8/20 µ s)
• Available in rack-mount or standalone configurations
• Made in the USA
2.2 DESCRIPTION
The Patton Electronics Model 1068/CO* and 1068/CP VDSL* modems
provide high-speed LAN connections between peered Ethernet LANs,
remote PC’s, or any other network enabled 10/100Base-T device.
Operating in pairs, a Model 1068/CO (central office) located at one end of
the LAN extension and a Model 1068/CP (customer premise) at the other
end, these units can automatically forward LAN broadcasts, multicasts,
and frames across a 2-wire voice-grade twisted-pair link.The data is
* Only Models 1068DV/CO and 1068DV/CP have POTS/ISDN split-
ters on board.

8
passed transparently (unmodified) through the 1068s.The 1068s automat-
ically add and delete MAC addresses, only passing packets across the
VDSL link that are meant for the remote peered LAN.
Figure 1. Typical application
The 1068DV/CO and 1068DV/CP work together to create a transparent
extension between two peered Ethernet LANs.POTS/ISDN calls can be
made over a VDSL link without interfering with the data.Figure 1 shows a
typical point-to-point application.

9
3.0 INSTALLATION
Because the Model 1068 requires no configuration, it can be installed
quickly.If you are installing a standalone unit, refer to section 3.1 “Standal-
one unit installation”.Otherwise, refer to section 3.2 “Rack card installation”.
Note If asymmetric transmission or line rates other than 12.5 Mbps
are required, refer to section 4.0, “Configuration” on page 15.
3.1 STANDALONE UNIT INSTALLATION
Do the following:
1. Connect the line interface between the units (refer to section 3.3,
“Connecting the Twisted-Pair Line Interface” on page 11)
Note See Figure 2 for the standalone unit’s rear panel arrangements.
2. Connect the Ethernet interface (refer to section 3.4, “Connecting the
10/100Base-T Ethernet Interface” on page 12).
3. Connect the power plug (refer to section 3.6, “Connecting Power”on
page 14).
Figure 2. Model 1068 standalone rear panel
Ethernet VLINK Power
Made in the USA
POTS/ISDN
twisted-pair
terminal block
interface
Power
jack
Ethernet VLINK Power
Made in the USA
Ethernet
port
VDSL twisted-pair
terminal block
interface
VDSL twisted-pair
RJ-45 interface
POTS/ISDN
1068DV
1068D

10
3.2 RACK CARD INSTALLATION
The Model 1068 rack card version comprises a front card and a rear
card.Do the following to install the cards into the rack chassis:
1. Slide the rear card into the back of the chassis along the metal rails.
2. Secure the rear card using the supplied metal screws.
3. Slide the front card into the chassis until you feel resistance as the
front card engages the rear card.When that happens,
gently push
the front card forward until it is fully seated in the card-edge recepta-
cle of the rear card (it should
click into place).
4. Secure the front card using the captive fasteners.
Note The Model 1001R14 chassis supports “hot swapping” of cards,
so it is not necessary to power down the rack when you install or
remove a Model 1068 rack card.
Figure 3. Model 1068 rack cards
5. Connect the line interface between the units (refer to section 3.3,
“Connecting the Twisted-Pair Line Interface” on page 11)
Note See Figure 3 for the rack card’s panel arrangements.
POTS/ISDN
1068DRC
1068DVRC
POTS/ISDN
Port
VLINK
RJ-45 interface
VLINK
terminal block
VLINK
RJ-45 interface
VLINK
terminal block
VLINK
VLINK
Ethernet
Ethernet
Port
Ethernet
Port
Ethernet

11
6. Connect the Ethernet interface (refer to section 3.4, “Connecting the
10/100Base-T Ethernet Interface” on page 12).
3.3 CONNECTING THE TWISTED-PAIR LINE INTERFACE
The Model 1068 supports communication between two peer Ethernet
LAN sites over a distance of up to 6,652 ft (2.03 km) over 24 AWG
(0.5 mm) twisted-pair wire.
Note Actual distance and link performance may vary depending on
the environment and type/gauge of wire used.
Follow the steps below to connect the Model 1068 VDSL Interfaces.
Note The Model 1068 units work in pairs.One of the units must be a
Model 1068/CO (Central Office), and the other unit must be a
Model 1068/CP (Customer Premise). It does not matter which
end is the 1068/CO and which is the 1068/CP.The link is always
initiated by the 1068/CP.As long as the 1068/CO is powered on,
the 1068/CP can establish a link by being powered on or by hav-
ing its power reset.
1. To function properly, the two Model 1068s must be connected
together using twisted-pair, unconditioned, dry, metal wire, between
19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through
signal equalization equipment are not acceptable.
2. The Model 1068 is equipped with two interface jacks that can be used
on the VDSL interface, an RJ-45 or a terminal block.These VDSL
interfaces are a two-wire interface.Observe the signal/pin relation-
ships on the Model 1068's VDSL interface jacks.
The RJ-45 connector on the Model 1068's twisted pair interface is polar-
ity insensitive and is wired for a two-wire interface.The signal/pin rela-
tionship is shown in Figure 4.
Figure 4. Model 1068 (RJ-45) twisted pair line interface.
1 (no connection)
2 (no connection)
3 (no connection)
4 (2-Wire RING)
5 (2-Wire TIP)
6 (no connection)
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8

12
The terminal block connector on the Model 1068's twisted pair interface
is polarity insensitive and is wired for a two-wire interface.The signal/pin
relationships is shown in Figure 5.
Figure 5. Model 1068D (Terminal Block) twisted pair line interface.
3.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE
The shielded RJ-45 port labeled Ethernet is the 10/100Base-T interface.
This port is designed to connect directly to a 10/100Base-T network.
Figure 6 shows the signal/pin relationships on this interface.You may
connect this port to another Ethernet device via a Type 4 or Type 5 cable
that is up to 328 ft long.
Figure 6. Model 1068 10/100Base-T RJ-45 Connector Pinout.
Ethernet VLINK Power
Made in the USA
RING TIP
1 TX+ (data output from 1068)
2 TX- (data output from 1068)
3 RX+ (data input to 1068)
4 (no connection)
5 (no connection)
6 RX- (data input to 1068)
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8

13
Connecting the 10/100Base-T Ethernet Port to a Hub
The Model 1068 10/100Base-T interface is configured as DTE (Data Ter-
minal Equipment), just like a 10/100Base-T network interface card in a
PC.Therefore, it “expects” to connect to a 10/100Base-T Hub using a
straight-through RJ-45 cable.Figure 7 diagrams the cable wiring for con-
necting the Model 1068 to a 10/100Base-T hub.
Figure 7. Wiring diagram for connecting the Model 1068 to a 10/100Base-T hub
Connecting the 10/100Base-T Ethernet Port to a PC (DTE)
The Model 1068 10/100Base-T interface is configured as DTE (Data Ter-
minal Equipment). If you wish to connect the 1068 to another DTE
devices such as 10/100Base-T network interface card in a PC (or 1068s
in a back-to-back arrangement), you must construct a 10/100Base-T
crossover cable as shown in Figure 8.
Figure 8. 10/100Base-T crossover cable
3.5 CONNECTING THE POTS/ISDN LINE
The RJ-45 port labeled “POTS/ISDN” is the POTS/ISDN interface.A tele-
phone or an ISDN device may be connected to this port and carried over
the VDSL line.The units do not need power for the POTS interface to
1068 10/100Base-T Port
RJ-45 Pin No. 10/100Base-T Hub RJ-45 Pin No.
1 (TX+)--------------------------------------------------1 (RX+)
2 (TX-)---------------------------------------------------2 (RX-)
3 (RX+)--------------------------------------------------3 (TX+)
6 (RX-)---------------------------------------------------6 (TX-)
1068 10/100Base-T Port
RJ-45 Pin No.
1 (TX+) 1 (TX+)
2 (TX-) 2 (TX-)
3 (RX+) 3 (RX+)
6 (RX-) 6 (RX-)
10/100Base-T DTE
RJ-45 Pin No.

14
work.The RJ-45 connector in the model 1068’s POTS/ISDN interface is
wired as shown in Figure 9.
Figure 9. Model 1068DV (RJ-45) POTS/ISDN interface
3.6 CONNECTING POWER
An external AC or DC power supply is available separately.This connec-
tion is made via the barrel jack on the rear panel of the Model 1068.No
configuration is necessary for the power supply (See Appendix B for
domestic and international power supply and cord options).
DC power (supplied via the power supply jack to the 1068) must meet
the following requirements; DC power supplied must be regulated
+5VDC ±5%, 1.0A minimum.Center pin is +5V.The barrel type plug has
a 2.5/5.5/10mm I.D./O.D./Shaft Length dimensions.
The Model 1068 does not have a power switch, so it powers up as soon
as it is plugged in.
1 (no connection)
2 (no connection)
3 (no connection)
4 (2-wire RING)
5 (2-wire TIP)
6 (no connection)
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8

15
4.0 CONFIGURATION
The Model 1068 has four DIP switches for configuring the unit for a wide
variety of applications.This section describes switch locations and
explains the different configurations.
4.1 CONFIGURING THE HARDWARE DIP SWITCHES
Using a small flat-tip screwdriver, remove the protective cover located on
the underside of the Model 1068 (see Figure 10).
Figure 10. Removing protective cover
Figure 11 and Figure 12 on page 16 show the orientation of the DIP
switches in the On and Off positions.
VLINK Modem
Power Link QOL Link Activity
VLINK Ethernet

16
Figure 11. DIP switch orientation
Figure 12. Rack card DIP switch orientation
S1
1234
ON
1234
ON
Push toggle up
for ON position
Switch toggle
Push toggle
down for
OFF position
1234
ON
S1
S1
S1
Power
VLINK Modem
Link
QOL
VLINK
Link
Activity
Ethernet
1234
ON
Push toggle to left
for ON position
Switch toggle
Push toggle
to right for
OFF position
1234
ON
S1
S1
1234
ON
S1

17
4.2 CONFIGURING DIP SWITCH S1
DIP switch S1 is where you configure theVDSL line rate, symmetric or
asymmetric, Ethernet full auto sense capability (100BaseT full or half
duplex, 10BaseT full or half duplex) or limited auto sense (only
100BaseT half duplex, 10BaseT full or half duplex). Table 1 summarizes
default positions of DIP switches S1-1 through S1-4. Detailed descrip-
tions of each switch follow the table.
Switch S1-1: Ethernet Auto Sense
Use switch S1-1 to configure the unit for full auto sense capability or lim-
ited auto sense capability. Full Auto sense capability consists of stan-
dard Ethernet Auto sensing (100BaseT full duplex, 100BaseT half
duplex, 10BaseT full duplex, and 10BaseT half duplex). Limited Auto
sensing capability consists on only auto sensing for 100BaseT half
duplex, 10BaseT full duplex, and 10BaseT half duplex. The limited auto
sensing feature is used when an Ethernet device does not comply with
IEEE 802.3x (back pressure flow control) at 100M full duplex.
Switches S1-2 and S1-4: Data Rate
Use switches S1-2 and S1-4 to configure the VDSL line rates.
Table 1: S1 Summary
Position Function Factory Default
S1-1 Ethernet Auto Sense OFF Full Auto Sense capability
S1-2 Line Rate ON
S1-3 Line Rate OFF 12.5Mbps Symmetric
S1-4 Line Rate OFF
Table 2: Ethernet Auto Sense Selection Chart
S1-1 Setting
OFF Full Auto Sensing
(100 Mbps, Full or Half Duplex)
(10 Mbps, Full or Half Duplex)
ON Limited Auto Sensing
(100 Mbps Half Duplex)
10 Mbps Full or Half Duplex)
Table 3: Symmetric VDSL Line Rates Selection Chart
S1-2 S1-3 S1-4 Symmetric Line Rate
ON ON ON 6.25 Mbps
ON ON OFF 9.38 Mbps

18
ON OFF OFF 12.5 Mbps
ON OFF ON 16.67 Mbps
Table 4: Asymmetric VDSL Line Rates Selection Chart
S1-2 S1-3 S1-4 Asymmetric Line Rates DS/US
OFF OFF ON 4.17 Mbps/1.56 Mbps
OFF ON ON 9.38 Mbps/1.56 Mbps
OFF ON OFF 16.67 Mbps/2.34 Mbps
Table 3: Symmetric VDSL Line Rates Selection Chart
S1-2 S1-3 S1-4 Symmetric Line Rate

19
5.0 OPERATION
Once the Model 1068s are properly installed, they should operate trans-
parently.No user settings required.This section describes reading the
LED status monitors.
5.1 POWER UP
Before applying power to the Model 1068, please review section 3.6,
“Connecting Power” on page 14 to verify that the unit is connected to the
appropriate power source.
5.2 FRONT PANEL LED STATUS MONITORS
The Model 1068 features five front panel LEDs that monitor power, the
Ethernet signals, and the VDSL connection. Figure 13 (standalone ver-
sion) and Figure 14 on page 20 (rack card version) show the front panel
location of each LED. Table 5 on page 20 describes the LED functions.
Figure 13. Model 1068 standalone unit front panel
Power
LED
VLINK Modem
Power Link QOL Link Activity
VLINK Ethernet
VLINK LED
VDSL
QOL LED
Ethernet
Link LED
Ethernet
Activity LED

20
Figure 14. Model 1068 rack card front panel
Table 5: Front panel LED description
LED Description
Power Solid GREEN to indicate the unit is powered on.
VLINK Link (Active Green) Solid green (ON) to indicate that the
end-to-end VDSL link between the Model 1068s is
established.The VLINK LED is OFF when the link is
down.
VLINK QOL (ActiveYellow) FlashesYELLOW to indicate the pro-
cessor is correcting an error in the data thus prevent-
ing the transmission of corrupted data to the Ethernet
port.The more error corrections, the more often the
LED blinks. If the light remains lit continuously, it
means that theVDSL line is noisy—although the data
at the Ethernet port remains uncorrupted. Further
impairment of the line however, risks having the line
fail, as indicated by the green VLINK Link LED extin-
guishing.
Ethernet Link (Active Green) Solid Green indicates that 10/
100Base-T Ethernet link has been established.
Ethernet Activity (ActiveYellow) Flashes yellow to indicate Ethernet
activity on the Model 1068’s 10/100Base-T Ethernet
port.
Power
VLINK Modem
Link
QOL
VLINK
Link
Activity
Ethernet
VLINK QOL
VLINK Link
Power
Ethernet Link
Ethernet Activity