Patton CopperLINK 2113A User manual

USER
MANUAL
MODEL 2113A
CopperLINK™ E1 Extender
SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
Part# 07M2113A-UM
Rev. A
Revised 2/2/12
An ISO-9001Certified
Company
This is a Class A device and is not intended for
use in a residential environment.
REGULATORY MODEL NUMBER:
03340D4-001

2
CONTENTS
1.0 Warranty Information ................................................................. 3
1.1 Regulatory Information ................................................................. 3
EMC Directive:.............................................................................. 3
Low-Voltage Direcive (Safety):..................................................... 3
1.2 Radio and TV Interference (FCC Part 15).................................... 4
1.3 CE Declaration of Conformity....................................................... 4
1.4 Authorized European Representative........................................... 4
1.5 Service.......................................................................................... 4
1.6 Safety When Working With Electricity .......................................... 5
2.0 General Information.................................................................... 7
2.1 Features........................................................................................ 7
2.2 Description.................................................................................... 7
3.0 Installation................................................................................... 8
3.1 Connecting the Line Port.............................................................. 9
3.2 Connecting the E1 Interface ....................................................... 10
3.3 Connecting Power ...................................................................... 10
4.0 Operation................................................................................... 11
4.1 Front Panel LED Status Monitors ............................................... 11
4.2 Configuration and Dip Switches.................................................. 12
Switch S4-1: Line Build Out........................................................ 12
A
Specifications ........................................................................... 13
A.1 Circuit Rate ................................................................................. 13
A.2 Circuit Interface .......................................................................... 13
A.3 Circuit Defaults ........................................................................... 13
A.4 Circuit Connector ........................................................................ 13
A.5 LED Status Indicators ................................................................. 13
A.6 Transmission Line ....................................................................... 13
A.7 Line Coding ................................................................................ 13
A.8 Line Interface .............................................................................. 13
A.9 Line Physical Connection ........................................................... 13
A.10 Power Supply .............................................................................. 13
A.11 Environmental ............................................................................. 13
A.12 Dimensions ................................................................................. 13
B
Model 2113A Series Factory
Replacement Parts and Accessories...................................... 14

3
1.0 WARRANTY INFORMATION
Patton Electronics warrants all Model 2113A components to be free
from defects, and will—at our option—repair or replace the product
should it fail within one year from the first date of the shipment.
This warranty is limited to defects in workmanship or materials, and does
not cover customer damage, abuse or unauthorized modification. If this
product fails or does not performs as warranted, your sole recourse shall
be repair or replacement as described above. Under no condition shall
Patton Electronics be liable for any damages incurred by the use of this
product. These damages include, but are not limited to, the following: lost
profits, lost savings and incidental or consequential damages arising
from the use of or inability to use this product. Patton Electronics spe-
cifically disclaims all other warranties, expressed or implied, and the
installation or use of this product shall be deemed an acceptance of
these terms by the user.
Note Conformity documents of all Patton products can be viewed
online at www.patton.com under the appropriate product page.
1.1 REGULATORY INFORMATION
EMC Directive:
• FCC Part 15, Class A
• EN55022, Class A
• EN55024
Low-Voltage Direcive (Safety):
• UL 60950-1/CSA 22.22 NO. 60950-1
• IEC/EN60950-1, 2nd Edition
• AS/NZS 60950-1

4
1.2 RADIO AND TV INTERFERENCE (FCC PART 15)
This device generates and uses radio frequency energy, and if not
installed and used properly-that is, in strict accordance with the manufac-
turer’s instructions-may cause interference to radio and television recep-
tion. The device has been tested and found to comply with the limits for a
Class A computing device in accordance with specifications in Subpart B
of Part 15 of FCC rules, which are designed to provide reasonable pro-
tection from such interference in a commercial installation. However,
there is no guarantee that interference will not occur in a particular instal-
lation. If the device does cause interference to radio or television recep-
tion, which can be determined by disconnecting the unit, the user is
encouraged to try to correct the interference by one or more of the follow-
ing measures: moving the computing equipment away from the receiver,
re-orienting the receiving antenna and/or plugging the receiving equip-
ment into a different AC outlet (such that the computing equipment and
receiver are on different branches).
1.3 CE DECLARATION OF CONFORMITY
Patton Electronics, Inc declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive
2004/108/EC relating to electromagnetic compatibility and Directive
2006/95/EC relating to electrical equipment designed for use within cer-
tain voltage limits. The Declaration of Conformity may be obtained from
Patton Electronics, Inc at www.patton.com/certifications.
The safety advice in the documentation accompanying this device shall
be obeyed. The conformity to the above directive is indicated by CE
mark on the device.
1.4 AUTHORIZED EUROPEAN REPRESENTATIVE
D R M Green, European Compliance Services Limited.
Avalon House, Marcham Road, Abingdon, Oxon OX14 1UD, UK
1.5 SERVICE
All warranty and non-warranty repairs must be returned freight prepaid
and insured to Patton Electronics. All returns must have a Return Materi-
als Authorization number on the outside of the shipping container. This
number may be obtained from Patton Electronics Technical Services at:
•Tel:[phone]
•Email:[e-mail]
• URL: http://www.patton.com

5
1.6 SAFETY WHEN WORKING WITH ELECTRICITY
• This device contains no user serviceable parts. This
device can only be repaired by qualified service per-
sonnel.
• Do not open the device when the power cord is con-
nected. For systems without a power switch and without
an external power adapter, line voltages are present
within the device when the power cord is connected.
• For devices with an external power adapter, the power
adapter shall be a listed Limited Power Source. The
mains outlet that is utilized to power the device shall be
within 10 feet (3 meters) of the device, shall be easily
accessible, and protected by a circuit breaker in com-
pliance with local regulatory requirements.
• For AC powered devices, ensure that the power cable
used meets all applicable standards for the country in
which it is to be installed.
• For AC powered devices which have 3 conductor
power plugs (L1, L2 & GND or Hot, Neutral &
Safety/Protective Ground), the wall outlet (or socket)
must have an earth ground.
• For DC powered devices, ensure that the interconnect-
ing cables are rated for proper voltage, current, antici-
pated temperature, flammability, and mechanical
serviceability.
• WAN, LAN & PSTN ports (connections) may have haz-
ardous voltages present regardless of whether the
device is powered ON or OFF. PSTN relates to inter-
faces such as telephone lines, FXS, FXO, DSL, xDSL,
T1, E1, ISDN, Voice, etc. These are known as “hazard-
ous network voltages” and to avoid electric shock use
caution when working near these ports. When discon-
necting cables for these ports, detach the far end con-
nection first.
• Do not work on the device or connect or disconnect
cables during periods of lightning activity.
WARNING

6
In accordance with the requirements of council direc-
tive 2002/96/EC on Waste of Electrical and Electronic
Equipment (WEEE), ensure that at end-of-life you sepa-
rate this product from other waste and scrap and deliver
to the WEEE collection system in your country for recy-
cling.
This device contains no user serviceable parts. This
device can only be repaired by qualified service per-
sonnel.
This device is NOT intended nor approved for connec-
tion to the PSTN. It is intended only for connection to
customer premise equipment.
Electrostatic Discharge (ESD) can damage equipment
and impair electrical circuitry. It occurs when electronic
printed circuit cards are improperly handled and can
result in complete or intermittent failures. Do the fol-
lowing to prevent ESD:
• Always follow ESD prevention procedures when
removing and replacing cards.
• Wear an ESD-preventive wrist strap, ensuring that it
makes good skin contact. Connect the clip to an
unpainted surface of the chassis frame to safely chan-
nel unwanted ESD voltages to ground.
• To properly guard against ESD damage and shocks,
the wrist strap and cord must operate effectively. If no
wrist strap is available, ground yourself by touching the
metal part of the chassis.
WARNING
WARNING
WARNING

7
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product. This
product has been thoroughly inspected and tested and is warranted for
one year for parts and labor. If any questions or problems arise during
installation or use of this product, contact Patton Electronics Technical
Support at [phone].
Note The 2113A includes software developed under third party
licenses. Contact Patton for more information.
2.1 FEATURES
• Easy-to-install E1 Extender—no configuration required
• Data rate set to 2.048 Mbps on an unframed E1
• Plug ‘n’ Play for easy installations
• LED indicators for Power, Ethernet Link, and Frame
• CE marked
2.2 DESCRIPTION
The Patton Electronics Model 2113A CopperLink provides high speed 2-
wire E1 extension connectivity to ISPs, PTTs, and enterprise environments
using binder group friendly TC-PAM modulation.
Line connection is made with an RJ-45 jack. The Model 2113A is powered
by an 100/230 VAC (Universal) supply. The E1 Extender features exter-
nally-accessible DIP switches, loopback diagnostics, and CopperLink Plug
‘n’ Play.

8
3.0 INSTALLATION
To install the 2113A E1 Extender, do the following:
1. Connect the line interface (refer to section 3.1, “Connecting the Line
Port” on page 9)
2. Connect the E1 interface (refer to section 3.2, “Connecting the E1
Interface” on page 10).
3. Connect the power plug (refer to section 3.3, “Connecting Power” on
page 10).
Figure 1. Model 2113A rear panel
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
CAUTION
Power
Line
RX (75 Ohm)
(Data from
G.703/G.704
network)
TX (75 Ohm)
(Data to
G.703/G.704
network)
E1 interface
(120 Ohm)

9
3.1 CONNECTING THE LINE PORT
Follow the steps below to connect the Model 2113A CopperLINK Line
port.
Note The Model 2113A units work in pairs. One of the units must be
configured as a (L) Local unit, and the other unit must be config-
ured as a (R) Remote unit.
To function properly, the two E1 Extenders must be connected together
using twisted-pair, unconditioned, dry, metal wire, between 19 (0.9mm)
and 26 AWG (0.4mm). Leased circuits that run through signal equaliza-
tion equipment are not acceptable.
Follow the steps below to connect the CopperLink line port:
1. Obtain a single-twisted pair cable with an RJ-45 plug connector at
each end.
2. Plug one end of the cable into the RJ-45 socket (labeled Line) on
the CopperLink 2113A.
3. When the remote and local extender units synchronize, the front-
panel green Line LED will turn on.
The RJ-45 connector on the Model 2113A's twisted pair interface is
polarity insensitive and is wired for a two-wire interface. The signal/pin
relationship is shown in Figure 2.
Figure 2. Model 2113A (RJ-45) twisted pair line interface.
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
CAUTION
1 (no connection)
2 (no connection)
3 (no connection)
4 (RING)
5 (TIP)
6 (no connection)
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8

10
3.2 CONNECTING THE E1 INTERFACE
Your CopperLink comes with an RJ-48C and dual BNC for connection to
E1.To connect the twisted pair cable to the CopperLink E1 port, attach
the male connector of the twisted pair cable to the female RJ-48 connec-
tor on the CopperLink. Attach the other end of the cable to the RJ-48
connector on the local E1.
The Model 2113A is equipped with dual female BNCs (TX and RX) for
connection to a 75-ohm dual coax E1 network interface. To connect the
BNC connectors of the E1 interface on the Model 2113A, simply use a
coaxial cable with a BNC connector at each end to connect the pair of
Model 2113As.
3.3 CONNECTING POWER
The Model 2113A does not have a power switch, so it powers up as soon
as it is plugged in.
An external AC or DC power supply is available separately. This connec-
tion is made via the barrel jack on the rear panel of the Model 2113A. No
configuration is necessary for the power supply (See Appendix B for
domestic and international power supply and cord options).
DC power (supplied via the power supply jack to the 2113A) must meet
the following requirements; DC power supplied must be regulated 5VDC
±5%, 1.0A minimum. Center pin is +5V. The barrel type plug has a
2.5/5.5/10mm I.D./O.D./Shaft Length dimensions.
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
CAUTION
CAUTION