Payment Express Colour Mini Vend Installation instructions

Payment Express® Colour Mini Vend (CMV)
Hardware Guide
Version 0.1

DOCUMENT REVISION INFORMATION
Version
Revision Information
0.1
Initial version.
RELATED DOCUMENTS
Version
Document Title
1.6.76
Payment Express SCR Serial Communications –SCR Serial Message Specification
A00
MI0022 Mounting Diagrams CMV300
COPYRIGHT
© Copyright 2017, Payment Express Limited
33 Wilkinson Road, Ellerslie
PO Box 8400
Auckland, 1150
New Zealand
www.paymentexpress.com
All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or
mechanical, including photocopying, without the express written permission of Payment Express Ltd.
PROPRIETARY NOTICE
The information described in this document is proprietary and confidential to Payment Express Limited. Any unauthorised
use of this material is expressly prohibited except as authorised by Payment Express Limited in writing.

CONTENTS
Document Revision Information..........................................................................................................................................2
Related Documents.............................................................................................................................................................2
Copyright.............................................................................................................................................................................2
Proprietary Notice ...............................................................................................................................................................2
1Overview......................................................................................................................................................................1
1.1 Terms and Acronyms.............................................................................................................................................1
1.2 Hardware Models...................................................................................................................................................1
1.3 Connectivity Diagram.............................................................................................................................................1
2CMV300 (AB0146).......................................................................................................................................................2
2.1 CMV300 Dimensions & Cut-Out.............................................................................................................................3
2.2 CMV300 Installation...............................................................................................................................................3
3Cables..........................................................................................................................................................................7
3.1 8-PIN Connector Pin-out........................................................................................................................................7
3.2 8-Pin to RJ45 Connector Pin-out............................................................................................................................7
4Secure Acceptance......................................................................................................................................................8
4.1 Serial Numbers ......................................................................................................................................................8
4.2 Sign of Tampering..................................................................................................................................................8
5Activation .....................................................................................................................................................................9
5.1 Authorised Customer Agents .................................................................................................................................9
5.2 Activation Process..................................................................................................................................................9
6Maintenance...............................................................................................................................................................10
6.1 Tradeouts & Deactivation Process.......................................................................................................................10
6.2 Maintenance Cards..............................................................................................................................................10
6.3 Cleaning Instructions............................................................................................................................................10
7Appendix....................................................................................................................................................................11
7.1 Contact Payment Express....................................................................................................................................11

1
1OVERVIEW
The Payment Express Colour Mini Vend (CMV) solution offers a complete solution for taking ICC Chip/Contactless
payments in an unattended environment.
Payment Express develops and owns the hardware design, intellectual property and processor platform to ensure end to
end accountability from card read to bankcard provider.
1.1 TERMS AND ACRONYMS
Term
Explanation
PIN
Personal Identification Number. In the context of card transactions this is typically a secret four digit
value, entered to approve a transaction
PCI
Payment Card Industry Standards Security Council (established 2006). Set data security standards for
hardware and software in the payments industry
PTS
PIN Transaction Security. As set of standards applied to a security standards applying to secure
devices such as the CMV300
CMV
Colour Mini Vend (version 300)
CRC
Cyclic Redundancy Check
MCU
Main Control Unit
RSA
RSA algorithm
AES
Advanced Encryption Standard
ICC
Integrated Circuit Card (chip card/smart card)
Host
The Payment Express Host. Provides e-commerce services on the internet
1.2 HARDWARE MODELS
The CMV solution consists of a core module, anti-removal device and mounting nuts.
Standard Unattended
Model
PX Product Code
Brief Description
CMV300
AB0146
Base module
Anti-removal device (AB0170)
M4 flange nuts (MF0099)
Please note that these are our standard models. When ordering or querying about a particular product please mention
the PX Product Code. Please contact Payment Express if you require a bespoke solution (see Appendix 7 for contact
details).
1.3 CONNECTIVITY DIAGRAM
CMV300 HOST
EQUIPMENT
RS232 Serial

2
2CMV300 (AB0146)
CMV300 Front View
CMV300 Rear View
Hardware Overview
Front Mount Design
RS-232 serial ports x1
Hardware accelerated encryption (Triple DES,
RSA and AES) and a CRC engine
Secure crypto MCU designed for POS
applications
Combined magnetic stripe card and ICC card
reader interface
Dedicated tamper grid and removal switch
monitor
Physical Link Interface
Please refer to the above photo (CMV300 Rear) for reference.
Connection with the customer equipment is via the 8-pin port labelled “HOST”.
Connection for the anti-removal device labelled “SEC”
Power Requirements
The device accepts DC regulated from +9V to +43.5V. SELV (Safety Extra Low Voltage)
When idle (no card inserted), power of 1400mW is drawn and when active 2800mW is drawn (3200mW max).
Operating & Storage Temperature Ratings
Storage: -20 to 80 degrees (Celsius)
Operating: -20 to 75 degrees (Celsius)
Standards & Compliance
EMV Contact Level 1 & 2
EMV Contactless Level 1 IN PROGRESS
PCI SRED (Secure Reading and Exchange of
Data) v5 IN PROGRESS
Additional Comments
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.

3
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
2.1 CMV300 DIMENSIONS & CUT-OUT
Recommended cut out dimensions for customer equipment.
Please note that mounting plates are not supplied by Payment Express Hardware and is the responsibility of the
customer to arrange their selected mounting method. All non-dimensioned lengths are subject to individual customer
machine fronts.
2.2 CMV300 INSTALLATION
DRAWING REQUIRED
#
PX Product Code
Description
Default QTY
1
AB0146
CMV300
1
2
AB0170
CMV300 M4 SEC with FPC Connector
1 (included with AB0146)
3
MW0142
CMV300 communications cable
1
4
MF0099
Nut M4 Flange OD 12mm
4 (included with AB0146)
5
Machine Mounting Plate (Customer Equipment)
Refer to Section 2.1
1

4
Installation Steps:
1. Prepare the mounting surface in accordance with the MI0020 mounting instructions. Make sure the edge of the
hole is smooth.
2. Connect the SEC (2) to the rear of the CMV300 as shown
3. Insert the communications cable (3) into the rear of the CMV300 as shown.

5
4. Remove the four nuts (4) from the CMV300.
5. Feed the SEC (2) and communications cable (3) through the hole in the mounting plate.
6. Insert the CMV300 into the Machine Mounting Plate (5).

6
7. Fit 3 of the M4 nuts (4) to the CMV300 mounting studs and tighten to 1.5 Nm.
8. Mount the SEC (3) on the remaining mounting stud, fit the remaining M4 nut (4), and tighten to 0.8 Nm. Ensure
M4 SEC (3) is mounted with silicone facing the M4 Flange Nut (4).
9. Connect the communications cable to the Host Application (customer application specific)
10. The device now needs to be activated before it can be used. Activation is done via a dual control process. Refer
to Section 5 (Activation) of this document for more information.
Silicone insert
faces away from
mounting plate
Nut over SEC
(3) uses lower
torque.

7
3CABLES
3.1 8-PIN CONNECTOR PIN-OUT
The interconnection between the CMV and the host application is made by a cable plugged into the 8-pin port. The pins
on this cable are allocated as follows:
Pin ID
Signal
Type
Description
1
TX
Output from CMV300
Transmit out. RS232 level, 115Kbps max
2
RTS
Output from CMV300
Request-To-Send. RS232 level
3
RX
Input to CMV300
Receive in. RS232 level, 115Kbps max
4
PWR
Power
9Vdc to 43.5Vdc.
5
PWR
Power
6
CTS
Input to CMV300
Clear-To-Send. RS232 level.
7
GND
-
System Ground
8
GND
-
3.2 8-PIN TO RJ45 CONNECTOR PIN-OUT
The standard cable for use with the CMV300 is MW0142. This crosses over the input and output signal lines to plug into
host equipment. The connections for the 8-pin end are as above, and the connections for the RJ45 are as follows:
Pin ID
Signal
Type
Description
1
RX
Input to CMV300
Receive in. RS232 level, 115Kbps max
2
CTS
Input to CMV300
Clear-To-Send. RS232 level.
3
TX
Output from CMV300
Transmit out. RS232 level, 115Kbps max
4
PWR
Power
9Vdc to 43.5Vdc.
5
PWR
Power
6
RTS
Output from CMV300
Request-To-Send. RS232 level
7
GND
-
System Ground
8
GND
-

8
4SECURE ACCEPTANCE
The CMV is a security device; therefore, the customer must check the following before installation.
4.1 SERIAL NUMBERS
Each unit (CMV) has their own unique serial number. Upon receiving the unit, the customer must check to ensure that
the serial number on the box matches the serial number on the unit.
Any discrepancies need to be reported to Payment Express (see Appendix 7.1 for contact numbers).
4.2 SIGN OF TAMPERING
The device should be checked upon receipt and then bi-monthly for the following signs of tampering:
The exterior of the device should have no (new) holes, signs of adhesives or stickers other than the device label
(as shown in Error! Reference source not found.a)
Only one silver-coloured magnetic read head should be visible on the magnetic swipe slot
No wires or foreign objects should be visible in the chip card reader slot as shown in Figure 1.
(a)
(b)
Figure 1: Foreign object and wires inserted into the device’s chip card reader slot. a) Normal slot –no wires visible.
b) Tampered slot - wires have been routed into right hand side of slot.
If any of the above signs of tampering is detected, please cease using the device immediately and arrange to return the
device to Payment Express Ltd. for examination per Section Error! Reference source not found..
4.3 LOSS OR THEFT
In the event that a CMV300 device is lost or stolen, please notify Payment Express immediately (see Appendix for
contact information).
Product name
Assembly and
version number
Firmware version
number
Serial number
(samples shown)

9
5ACTIVATION
The CMV300 solution requires activation before the devices can begin processing. Activation is required for initial
installations and re-installations. Activation is done via a dual control process.
5.1 AUTHORISED CUSTOMER AGENTS
Prior to the installation process beginning two or more customer agents are authorised by Payment Express for the
activation of devices. The customer agents are trusted individuals nominated by the customer.
Once the customer agents are established, Payment Express will issue a unique login (username/password) to each
customer agent. These logins are used to access the Payment Express website required for the dual control Activation
process.
5.2 ACTIVATION PROCESS
Two authorised customer agents must be available for the Activation process to begin.
1. Log on to Payment Express
Two of the authorised customer agents start separate sessions to log on to the Payment Express website using
their individual logins.
2. Identify Terminal(s)
Once logged in, the terminals available for installation are displayed.
3. Authorise Terminal(s)
Both of the customer agents will authorise the terminal(s) for installation via the Payment Express website. This
authorisation will require a password.
When both agents approve a terminal for installation the host terminal information will enter into the “Ready for
Installation” state pending communications from the terminal. This “Ready for Installation”state will revert to a
“Removed”state if physical installation and communication with the terminal do not occur within 24 hours. The
agents will need to start the Activation process again if this occurs.
For audit purposes, a record will be created in the Payment Express host database for all state changes
(including the login used and a timestamp).
Utilizing the 24 hour window, authorised customer agents can choose to begin the Activation process at the
time of physical installation or initiate the Activation process prior to the physical installation if they know the
physical installation will be done within the next 24 hours.
4. Physical Installation
Within the 24 hour window, the installation technician will physically install the CMV300 into their mountings.
The devices must be connected to communications and the secure channel established to the CMV300.
5. Terminal Logon
The installation technician will trigger a transaction via the vendor’s point of sale which will fail with a removal
detection error code (W0) and an on-screen message “MAINTENANCE IN PROGRESS”. The terminal firmware
will automatically force a logon, upon which the terminal state is then updated.
6. Ready State (Activation Process Complete)
The terminal and is now authorised for processing transactions. The installation technician should run another
test transaction (using a valid payment card) to confirm correct operation. This transaction should successfully
process.

10
6MAINTENANCE
6.1 TRADEOUTS & DEACTIVATION PROCESS
In the event that the CMV300 device needs to be swapped out or deactivated, please follow instructions below.
1. Call Payment Express Support to log a ticket (see appendix 10.1 for contact numbers). Please provide the
following information.
Serial Number(s) of CMV300 device(s).
Brief description of fault / reason for deactivation.
Contact Name.
Contact Phone Number.
Shipping Address (for replacement if needed).
2. Physically remove the device(s). At next communication with the host the device will be marked as removed.
3. Ship the device(s) back to Payment Express.
6.2 MAINTENANCE CARDS
The card reader slot in the CMV unit should be checked on a regular basis. This is to ensure that nothing is lodged inside
the card reader slot that may prevent successful card reads or pose a security threat.
The card reader slot can be checked by using a standard maintenance card or standard credit card to ensure smooth
insert & remove operation.
6.3 CLEANING INSTRUCTIONS
The external face of the CMV300 device should be carefully cleaned on a regular basis. This is to ensure that the
keyboard and display are free of dirt and solvents which could damage the device or prevent users from using the device
as intended.
Payment Express recommend cleaning the device with a damp cloth. Do not use any solvents as this may damage the
device surface.

11
7APPENDIX
7.1 CONTACT PAYMENT EXPRESS
Phone
International
[phone]
Australia
1 800 006 254 or [phone]
Hong Kong
[phone]
New Zealand
0800 PAYMENT (729 6368) or 09 309 4693
Singapore
[phone]
South Africa
[phone]
United Kingdom
[phone]
USA
[phone]
E-mail
Sales
[email protected]
Support
[email protected]
Dev Support
[email protected]