pdlux PD-PIR69 User manual

The product is a kind of energy-saving automatic lamp, which can be on when
someone comes and off after leaves. it can identify day and night automatically. It
adopts a high-stable sensor and integrated IC, its performance is stable and
reliable. When someone enters the detection range, infrared sensor will trigger the
lamp work, the lamp turn on and after some time it turn off.
12m 120°
●It can identify automatically day and night, what’s more, working light can be adjusted freely, so it can work
automatically at night and stop in the daytime;
●Sensitivity is adjustable, by adjusting SENS to adjust sense distance;
●Time setting(TIME) can be adjusted; users can adjust it according to local condition.
Correct moving orientation Detection angle
IP: 44
Power source: 220-240V/AC
100-130V/AC
100-240VAC
Power frequency:50/60Hz
Rated load:75Wx2 Max., JD bulb
Time setting: 5sec~10min±2min(adjustable)
Light-control: 10LUX~daylight(adjustable)
Detection angle(22°C): 120°
Detection range: 12m Max.(adjustable)
Woking temperature: -10°C~+40°C
Woking humidity: ≤93%RH
Installation height: 1.5~3m
Weight: about 0.642kg
1.Choose installation place as your need, mark two installation holes with a pencil.
2.Place the lamp in a safe place avoiding some unnecessary damage.
3.On the sign bore two installation holes(Φ6mm , height 35mm).
4.Strike the plastic dilatant into the two holes.
Infrared Sensor Lamp
PD-PIR69 instruction
www.pdlux.com Tel: [phone]
250mm
74mm
165mm
190mm
PRODUCT INFORMATION
SPECIFICATIONS
SENSOR INFORMATION
FUNCTION
INSTALLATION

5.Connect power line into “1” and “2” in the diagram.
6.Electrify it, the power voltage must be in accord with the voltage indicated.
7.Fix the lamp in the installation location with screw.
1. After installation, before electrifying it, turn the time knob(TIME)
clockwise to the minimum and turn the photocell knob (LUX))
clockwise to the maximum(☼), turn the sensitivity knob(SENS)
clockwise to the maximum.(like right diagram)
2. Electrify it. After 5 seconds, the lamp should be on.
3. 5-10 seconds later after the lamp turn off (no sense condition),
make it sense, the lamp should be on, under no sense signal
condition, the lamp should turn off within 5sec~10sec.
4. If all are normal, turn the time setting knob to confirm the light time
you want; turn the photocell knob to change the light-control; and turn
the sensitivity knob to adjust the detection range.
-
+
SENS
-
LUX
+
TIME
1. Avoid installing the product in the locations where the sunlight irradiate or air current and
temperature change obviously;
2. Avoid touching the detection window with sharp and stiff things or coarse pollutants;
3. When the lamp is off and then again on, you should adjust the angle between the lamp head and
the sensor, and turn the sensitivity knob (SENS) properly to solve the problem.
5. Caution: the product can continuously sense as long as signal has made it work: If the product is
tested in the daytime (the light set is less than 10lux), with opaque cover the lens, after the unit works,
take off the opaque and let it receive natural light, here it can sense continually. After the load stop to
work, it can work only when the light-control is less than 10lux.
12
74mm
ATTENTION: When use this product, please adjust the sensitivity to an appropriate position you need,
please do not adjust the sensitivity to maximum, to avoid the product does not work normally caused
by wrong motion.Because the sensitivity is too high easily detect the wrong motion by wind blowing
leaves & curtains, small animals, and the wrong motion by interference of power grid & electrical
equipment. All those lead the product does not work normally !
When the product does not work normally, please try to lower the sensitivity appropriately, and then
test it.
Infrared Sensor Lamp
PD-PIR69 instruction
www.pdlux.com Tel: [phone]
TEST
CAUTIONS
Solutions of prevent the power network pulse interference the products:
Due to the difference of regional interference power network, the pulse of interference is
uncertain,so the user are not suggested to adjust the sensitive to the maxium when
using.Suggestion:Please install and adjust the sensitive in the appropriate distance
using,do not set the maxium sensitivity to prevent misoperation.

Infrared Sensor Lamp
PD-PIR69 instruction
www.pdlux.com Tel: [phone]
Warning!
● When used in different environments, please do not to adjust the sensitivity to the highest.
Because that could easily lead to malfunction.
● Please confirm with prefessional installation.
● Please cut off power supply before installation and removal operations.
● Make sure that you have cut off the power for safety purposes.
● Improper operation caused losses, the manufacturer does not undertake any responsibility.
We are committed to promoting the product quality and reliability, however, all the electronic
components have certain probabilities to become ineffective, which will cause some
troubles.When designing, we have paid attention to redundant designs and adopted safety
quota to avoid any troubles.
This instruction, without our permission, should not be copied for any other purposes.
Add: 17F,Commerce Building of NingBo,
No 588, South Tiantong Rode,Yinzhou District,Ningbo，China
Tel: [phone](20 lines) Fax: [phone]
Email: [email protected] Web: www.pdlux.com