Peak PCAN-MicroMod User manual

PCAN-MicroMod Evaluation
Test and Development Environment
for the PCAN-MicroMod
User Manual
Document version 2.0.3 (2019-03-11)

PCAN-MicroMod Evaluation - User Manual
2
Relevant products
Product Name Part number Model
PCAN-MicroMod Evaluation Board IPEH-002082
PCAN-MicroMod Evaluation Kit 1
(PCAN-Dongle)
IPEH-002081
PCAN-MicroMod Evaluation Kit 2
(PCAN-USB)
IPEH-002079
Evaluation Board
Rev. 1.3
The cover picture shows the MicroMod Evaluation Board with plugged on PCAN-
MicroMod.
PCAN® is a registered trademark of PEAK-System Technik GmbH. CANopen® and
CiA® are registered community trade marks of CAN in Automation e.V.
All other product names mentioned in this document may be the trademarks or
registered trademarks of their respective companies. They are not explicitly marked
by “™” and “®”.
© 2019 PEAK-System Technik GmbH
PEAK-System Technik GmbH
Otto-Roehm-Strasse 69
64293 Darmstadt
Germany
Phone: [phone]
Fax: [phone]
www.peak-system.com
[e-mail]
Document version 2.0.3 (2019-03-11)

PCAN-MicroMod Evaluation - User Manual
3
Contents
1 Introduction 4
1.1 Properties at a Glance 4
1.2 Scope of Supply 5
2 Setting Up the Evaluation Kit for Operation 6
3 Components of the Evaluation Board 7
3.1 Power Supply 7
3.2 CAN Connector 8
3.2.1 Connector Shield 9
3.2.2 High-speed CAN Bus Termination 9
3.2.3 5-Volt Supply for External Devices 10
3.2.4 Low-speed CAN (ISO 11898-3) 11
3.3 MicroMod Position 14
3.4 Digital Inputs 15
3.5 Frequency Inputs 16
3.6 Digital Outputs 17
3.7 Frequency/PWM Outputs 18
3.8 Analog Inputs 19
3.9 Serial Bus (SCL, SDA, INT) 20
3.10 Prototyping Areas 21
3.11 RS-232 Connector 22
3.11.1 Connector Shield 23
4 Uploading Firmware to the MicroMod 24
5 Technical Specifications 29
Appendix A Circuit Diagram of the
Evaluation Board 31

PCAN-MicroMod Evaluation - User Manual
4
1 Introduction
The PCAN-MicroMod Evaluation Board facilitates the entry into
work with the PCAN-MicroMod and into development of own mo-
therboards for the module. With a diversity of LEDs, switches, and
potentiometers the performance of a MicroMod configuration can
easily be tested. All inputs and outputs are accessible via pickoffs
and screw terminals. Via the serial RS-232 interface firmware to be
tested is transferred to the MicroMod.
A kit helps establishing the CAN communication between a PC and
the MicroMod, either for transferring a new configuration, or for
monitoring and influencing the CAN traffic.
Note: This user manual only refers to the Evaluation Board and
its application within the scope of the kits. Separate manuals
exist for the PCAN-MicroMod and for the CAN interfaces PCAN-
Dongle and PCAN-USB.
1.1 Properties at a Glance
Pickoffs and screw terminals for inputs and outputs
Open collector drivers for the digital and the CMOS PWM
outputs
Protected digital inputs
Low-pass for digital inputs
LEDs for digital inputs and outputs
Switches for status modification of the digital inputs
Potentiometers for analog inputs
Voltage divider for voltages > 5 V

PCAN-MicroMod Evaluation - User Manual
5
Serial RS-232 connector for firmware upload from a PC
Optional insertion of a Low-speed CAN transceiver alternatively
to the High-speed CAN transceiver on the MicroMod
1.2 Scope of Supply
PCAN-MicroMod Evaluation Board
AC adaptor
Configuration software for Windows 10, 8.1, 7 (32/64-bit)
Manual and circuit diagram of the Evaluation Board in PDF
format
Additionally with Kit 1/Kit 2 (IPEH-002081/79)
PCAN-MicroMod
2 m CAN cable with termination on both ends (each 120 ) for
High-speed CAN
CAN interface PCAN-Dongle PS/2 (Kit 1)
CAN interface PCAN-USB (Kit 2)

PCAN-MicroMod Evaluation - User Manual
6
2 Setting Up the Evaluation
Kit for Operation
This chapter gives a quick overview of the needed steps for the
straightforward startup of the Evaluation Kit.
Do the following for the setup:
1. Only PCAN-Dongle: Connect the PCAN-Dongle to the
switched off PC. Start the PC.
2. On the PC under Windows, install the device driver for ei-
ther the PCAN-Dongle or the PCAN-USB adapter from the
supplied CD.
3. Only PCAN-USB: Connect the PCAN-USB adapter to the PC.
4. Connect the PCAN-Dongle or the PCAN-USB adapter and
the Evaluation Board using the CAN cable.
5. Connect the AC adaptor to the Evaluation Board in order to
supply it.
6. Under Windows, install the configuration program PCAN-
MicroMod Configuration from the supplied CD (Tools
section).
7. Start PCAN-MicroMod Configuration, create a configuration,
and finally send this configuration to the MicroMod (see
program help).
8. You can now work with signals at the I/O ports as defined in
the configuration. Please consider the explanations in the
following chapter. For monitoring and transmitting CAN
messages on the PC side, you can use the simple CAN
monitoring software PCAN-View.

PCAN-MicroMod Evaluation - User Manual
7
3 Components of the
Evaluation Board
This chapter describes the function units and connectors of the Eva-
luation Board. For details you can also refer to the circuit diagram in
Appendix A on page 31.
3.1 Power Supply
The Evaluation Board is supplied by the included AC adaptor with
9 V DC (connector J11, upper left). When using an alternative vol-
tage supply, the input voltage can be in the range of 6.4 to 12 V. The
voltage regulator on the board provides the necessary supply for
the MicroMod (JP31 shortened on position 1-2, delivery status).
Figure 1: Polarity of the supply socket
The LED LD25 indicates that the Evaluation Board is supplied.
At higher input voltages and concurrent higher environment tempe-
ratures (e.g. 12 V, above room temperature) an alternative voltage
regulator 7805 with heat sink can be inserted on position J19.
Optionally the use of an integrated switch regulator (e.g. PT5101,
PT78HT205, PT78ST105, each by Texas Instruments) is possible. For
example, this is reasonable in an environment with higher input
voltage (e.g. 24 V). In all cases each JP30 and JP31 must be shor-
tened in position 2-3 (positions 1-2 stay open).

PCAN-MicroMod Evaluation - User Manual
8
3.2 CAN Connector
The 9-pin D-Sub male connector J17 is used for CAN connection,
positioned on the mid right of the Evaluation Board. The pin assign-
ment of the CAN connector corresponds to the specification CiA®
303-1.
Figure 2: Position of the CAN connector
Figure 3: Assignment of the D-Sub male connector for CAN

PCAN-MicroMod Evaluation - User Manual
9
3.2.1 Connector Shield
With solder jumpers on the positions JP22 and JP25 on the bottom
side of the Evaluation Board the ground can be connected to the
connector shield.
Figure 4: Positions JP22 and JP25 on the bottom side of the Evaluation Board
3.2.2 High-speed CAN Bus Termination
If the Evaluation Board is connected to one end of the High-speed
CAN bus and the CAN bus is not terminated at that end, a termina-
tion can be activated on the Evaluation Board. To do so, solder
jumpers are set on positions JP23 and JP24 (delivery status: open =
no termination).

PCAN-MicroMod Evaluation - User Manual
10
Figure 5: Positions JP23 and JP24 on the bottom side of the Evaluation Board
For better electromagnetic compatibility a split termination is
implemented.
Figure 6: Split termination for the High-speed CAN bus
3.2.3 5-Volt Supply for External Devices
With solder jumpers on position JP32 a 5-Volt supply can be routed
to pin 1, pin 9, or to both pins (delivery status: open = no supply).
Thus devices with low power consumption (e.g. a bus converter)
can be directly supplied via the CAN connector.

PCAN-MicroMod Evaluation - User Manual
11
Figure 7: Position JP32 on the bottom side of the Evaluation Board
5-Volt supply None Pin 1 Pin 9 Pin 1 + Pin 9
Solder jumper(s) on JP32 none 2-3 1-2 1-2-3
3.2.4 Low-speed CAN (ISO 11898-3)
A Low-speed CAN transceiver TJA1054 can be equipped on position
U5 of the Evaluation Board. The following measures are additionally
necessary for Low-speed CAN operation:
On the MicroMod, the 0-Ohm resistor below and right to the
label “4” must be unsoldered in order to disconnect the High-
speed CAN transceiver from the CAN controller.
Figure 8: Position of the 0-Ohm resistor on the MicroMod

PCAN-MicroMod Evaluation - User Manual
12
The solder jumpers on the positions JP28 and JP29 must be
shifted from HS (High-speed) to LS (Low-speed).
Figure 9: Positions JP28 and JP29 on the bottom side of the Evaluation Board
The lines CAN_L and CAN_H are terminated with 5.6 keach.
For a termination with lower resistance the resistors R2 and R3
can be equipped in addition. They are in parallel with the
existing termination resistors.
Figure 10: Positions R2 and R3

PCAN-MicroMod Evaluation - User Manual
13
The error condition of the Low-speed CAN transceiver is indicated
by the LED LD26.
Figure 11: Position of the error status LED for Low-speed CAN, and position JP21
For again operating with High-speed CAN, the equipped Low-speed
CAN transceiver can be deactivated by setting a solder jumper on
position JP21. Furthermore, the first two measures must be undone.
On the MicroMod a solder jumper instead of the 0-Ohm resistor is
sufficient.

PCAN-MicroMod Evaluation - User Manual
14
3.3 MicroMod Position
When you mount the MicroMod, take notice of the white triangular
marks on each the Evaluation Board and the MicroMod (upper left
corner). These marks must align.
Figure 12: MicroMod position
Figure 13: Positioning marks on the MicroMod
and the Evaluation Board
Another help may be the orientation of the labeling. With mounted
MicroMod the labels have the same orientation on both PCBs (not
upside down).

PCAN-MicroMod Evaluation - User Manual
15
3.4 Digital Inputs
The Evaluation Board has 8 digital inputs with TTL levels. The
corresponding connector is J3 (screw terminals on the lower left).
Figure 14: Area of the digital inputs
with the associated DIP switches and LEDs
Each input has a pull-up resistor (10 k) and is Low-active, so the
inputs are switched against GND. Each input status is indicated by
an LED. For test purposes the input signal can be switched with the
dip switch S1. The corresponding switches are labeled “Din0” to
“Din7”. The inputs have a low-pass filter with 100 k/4,7 nF.
Signals leading directly to the MicroMod can be picked off at the
measuring points on strip J20, positions 6 to 13 (position 1 is the
upper one).

PCAN-MicroMod Evaluation - User Manual
16
3.5 Frequency Inputs
The Evaluation Board has 4 frequency inputs. The corresponding
connector is J2 (Fin0 to Fin3, screw terminals on the mid left).
Figure 15: Area of the frequency inputs
with the associated DIP switches, LEDs, and the solder positions for adjustments
The MicroMod can meter frequencies from 1 Hz to 10 kHz.
To activate a low-pass for the input path, a capacitor with 4.7 nF can
be engaged behind the existing series resistance of 100 kby using
solderbridges for positions JP13 to JP16.
Frequency input Solder jumpers for
low-pass on position
Fin0 JP16
Fin1 JP15
Fin2 JP14
Fin3 JP13

PCAN-MicroMod Evaluation - User Manual
17
3.6 Digital Outputs
The Evaluation Board has 8 digital outputs. The corresponding
connector is J1 (screw terminals on the upper left).
Figure 16: Area of the digital outputs
with the associated LEDs and the solder positions for adjustments
The outputs are Low-side switches with a maximum load of
350 mA. The LEDs LD1 to LD8 indicate each status of the outputs. If
an LED is on, the output is active and is switched against ground.
With solder jumpers on positions JP1 to JP8 a pull-up resistor
(3.3 k) can be engaged for each output (delivery status: open =
Low-side switch).
With a solder jumpers on position JP10 the outputs 0 to 3 and on
position JP9 the outputs 4 to 7 can be inverted by hardware
(delivery status: open = not inverted).

PCAN-MicroMod Evaluation - User Manual
18
3.7 Frequency/PWM Outputs
The MicroMod can generate frequency signals and PWM signals.
The corresponding connector is J2 (Fo0 to Fo3, screw terminal on
the mid left).
Figure 17: Area of the frequency/PWM outputs
with the associated LEDs and the solder positions for adjustments
The output signal is protected against short circuit with a series
resistance of 82 .
With a solder jumper on position JP11 the output signal can be
inverted by hardware (delivery status: open = not inverted).

PCAN-MicroMod Evaluation - User Manual
19
3.8 Analog Inputs
The Evaluation Board has 8 analog inputs. The corresponding
connector is J4 (screw terminals on the upper right).
Figure 18: Area of the analog inputs
with the associated potentiometers and the solder positions for adjustments
The analog reference voltage is 5 V. The input impedance is 6.5 k
(3.2 kanalog input microcontroller, 3.3 kseries impedance in
front of the microcontroller input).
The Evaluation Board has 4 potentiometers (P0 to P3) which can be
used for simulating input signals. With solder jumpers on positions
JP17 to JP20 the potentiometers are connected to Ain0 to Ain3
(delivery status: closed = connected).
For external sensors the screw terminals provide the supply
positions AGND and AVCC.

PCAN-MicroMod Evaluation - User Manual
20
3.9 Serial Bus (SCL, SDA, INT)
The ports SCL, SDA, and INT on the strip J15 do not have a function
with the standard firmware for the MicroMod. In connection with an
alternative firmware, they can be used for a serial bus (e.g. I2C or
SPI).
Figure 19: Position of strip J15
J15 Pin MicroMod Function
SCL J1:19 Serial Clock
SDA J1:20 Serial Data (I2C) / Serial Data Out (SPI)
INT J1:22 Serial Data In (SPI)
GND Ground
VCC Supply voltage 5 V DC