2
Trans ucer complement:
Low frequency section:
remium grade 10" woofer
High frequency section:
eavey 14XT™titanium diaphragm
compression driver on a 90˚ x 60˚ constant
directivity horn
Box tuning frequency:
Low Frequency Section: 78 Hz
Harmonic istortion:
1% rated power
Second harmonic:
100 Hz: 0.43%
1 kHz: 0.07%
Third harmonic:
100 Hz: 0.58%
1 kHz: 1.02%
10% rated power
Second harmonic:
100 Hz: 2.28%
1 kHz: 0.40%
Third harmonic:
100 Hz: 0.97%
1 kHz: 2.02%
Electro-acoustic crossover frequency
(internal passive):
2.8 kHz
Impe ance (Z):
Full range:
Nominal: 8 Ω
Minimum: 5.4 Ω
Input connection:
One four-pin Neutrik®Speakon®in parallel
with one two-position terminal strip
Enclosure materials & finish:
Dado-joined 12 mm birch finished with a
textured acrylic polyurethane with a full-
length metal grille covered in acoustical-
grade grille cloth. Available in black, white or
natural finishes.
Dimensions (H x W x D):
14.56" x 19.63" x 15.95"
370 mm x 498 mm x 405 mm
Net weight:
29 lbs. (13.2 kg)
Frequency response
This measurement is useful in determining
how accurately a given unit reproduces an
input signal. The frequency response of the
SSE 10M is measured at a distance of 1
meter using a 1 Watt swept-sine input signal
(into the nominal impedance). As shown in
figure 1, the selected drivers in the SSE 10M
combine to give a smooth frequency
response from 80 Hz to 17 kHz.
Power han ling
There are many different approaches to
power handling ratings. eavey rates this
loudspeaker system's power handling using
a full-range form of the AES Standard 2-
1984. Using audio band 20 Hz to 20 kHz
pink noise with peaks of four times the RMS
level, this strenuous test signal assures the
user that every portion of this system can
withstand today's high technology music.
This rating is contingent upon having a
minimum of 3 dB available amplifier
headroom.
Harmonic istortion
Second and third harmonic distortions vs.
frequency are plotted in figures 3 & 4 for two
power levels: ten percent (10%) of rated
input power and either one percent (1%) of
rated input power or 1 Watt, whichever is
greater. Distortion is read from the graph as
the difference between the fundamental
signal (frequency response) and the desired
harmonic. As an example, a distortion curve
that is down 40 dB from the fundamental is
equivalent to 1% distortion.
Architectural & engineering
specifications
The loudspeaker system shall have an
operating bandwidth of 80 Hz to 17kHz. The
nominal output level shall be 95 dB when
measured at a distance of one meter with an
input of one Watt. The nominal impedance
shall be 8 ohms. The maximum program
power handling shall be 400 Watts, with a
peak power input of at least 800 Watts and a
minimum amplifier headroom of 3 dB. The
nominal radiation geometry shall be 90° in
the horizontal plane and 60° in the vertical
plane. The outside dimensions shall be
14.56" high by 19.63" wide by 15.95" deep.
The weight shall be 29 lbs. The loudspeaker
system shall be a model SSE 10M.
3 + 2 YEAR LIMITED WARRANTY
NNOOTTEE:: For details, refer to the warranty
statement. Copies of this statement may
be obtained by contacting eavey
Electronics Corporation, .O. Box 2898,
Meridian, Mississippi 39301-2898.or 1 watt)
