Pedigree Technologies OneView Cab-Mate Flex User manual

INSTALLATION MANUAL
PedigreeTechnologies.com | Support: (701)-499-0022
Cab-Mate Flex (from Cab-Mate
Connect)
Document ID:IM-CMFX
Last Updated: October 08, 2021
Pedigree Technologies recommends using a professional installer for optimal
results. Please let your Pedigree Technologies representative suggest a provider if
you need help with your hardware installations.

2
INSTALLATION MANUAL
Prerequisites
PedigreeTechnologies.com | Support: (701)-499-0022
Required Information [*needed for nal activation of hardware - see last page]
• Name of asset*(ex: Propane Truck #20)
• Detailed information about the asset*(year, make, model, VIN, license plate, etc.)
• State, area, organization, or group the asset belongs to (ex: North Region, MN tankers, etc.)
• ESN of each device to be installed* (ESN is found on the back of each unit with a barcode)
• Current odometer reading
• Type of diagnostics connector, if possible (6 pin, 9 pin square flange, 9 pin round threaded,
J1962, Type II, etc.)
Required Equipment
Required Tools
• Drill and assorted drill bits (ex. to mount cradle)
• Slotted, Philips, and/or Torx bits (you may need tamper resistant Torx bits)
• Panel removal tool or plastic pry bar (to remove dash panel(s) as needed)
• Small socket set
• Zip Ties (to hold cabling in place)
Cab-Mate Flex Cradle Tablet
Hardware Pack
In-Cab Readiness Kit
(booklet, stickers, DOT reference card)
(5) #8 Self-tapping Screw 3/4 inch
(5) M4 Screw 12mm
(5) M4 Screw 8mm
(5) M4 Steel Nut
(11) M4 Star Lock Washer
(2) M4 Tamper Resistant Button Head HEX
Screw 20MM

PedigreeTechnologies.com | Support: (701)-499-0022
3
STEP ONE
Unplug the cable from the Cab-Mate Connect
cradle. This cable will plug into the new cradle in
a later step.
Before You Begin
TURN TO THE LAST PAGE - WRITE DOWN THE REQUIRED INFORMATION!!!
• Decide where the hardware components will be located. If necessary remove any dash
panels with removal tool.
• Must be within reach of the diagnostic cable to be installed.
• Must be protected from moisture, excessive dust/dirt, heat (away from heater vents) and
unobtrusive to driver operation or eld of view.
• Routing of the cable between the factory diagnostic port and the telematics device does not
cause excessive bending/kinking or areas where vibration may jeopardize the integrity of
the hardware.
• Cabling must not impede function of any rotating or moving parts (ex. Steering
mechanisms, wiper mechanisms, or brake pedal)
• Ensure that the mounting location has enough integrity to accommodate the additional
weight and vibration of the device.
Cab-Mate Connect to Cab-Mate Flex
Remove Cab-Mate One
Cab-Mate Connect Cradle
STEP TWO
Detach the ball mount from the back of the cradle
by removing the four screws that secure it. It may
be easier to remove the mount by detaching the ball mount section. The ball mount section can
be attached to the new cradle assembly.
Ball Mount on Cab-Mate Flex Cradle

Testing / Conrmation Steps
PedigreeTechnologies.com | Support: (701)-499-0022
Cab-Mate Connect to Cab-Mate Flex
Install Conrmation: 701-499-0022
You will be prompted for the following information during the set up process
• Device ESN
• Name of Asset (ex. Service Truck 51)
• Year, make, and model
• VIN #
• License plate #
• Mileage Hours
STEP FOUR
Call Pedigree Technologies support to conrm installation before replacing any of the dash
panels you may have removed during cable installation.
STEP THREE
Plug the cable from the previous Cab-Mate
Connect into the 6 pin port on the Cab-Mate Flex.

PedigreeTechnologies.com | Support: (701)-499-0022
5
Installation Steps, Continued
Alternative Installation
Cab-Mate Connect to Cab-Mate Flex
STEP ONE
Remove all cables from the back of the previously
installed 3640 LMU. You will re-attach the
diagnostic cable in a later step, but all other
connected cables can be removed.
LMU
STEP TWO
Place the empty 3640 LMU into the bracket on the
Cab-Mate Flex cradle assembly and snap into place
to secure.
STEP THREE
Connect the 22 pin connector from the Cab-Mate Flex cradle assembly to the LMU.
Cab-Mate Flex Cradle Assembly
LMU

PedigreeTechnologies.com | Support: (701)-499-0022
6
Connect Diagnostics Cable to Cradle
Cab-Mate Connect to Cab-Mate Flex
STEP FOUR
Plug the canbus cable that you removed from the LMU in an earlier step, into the 16 pin port on
the 3640 LMU (the only open port).
16 Pin Connector
from canbus cable
STEP FIVE
(If not already pre-assembled) Connect the 6 pin plug (smaller of the two plugs) from the LMU
assembly into the matching port on the back of the cradle.

Testing / Conrmation Steps
PedigreeTechnologies.com | Support: (701)-499-0022
Cab-Mate Connect to Cab-Mate Flex
Install Conrmation: 701-499-0022
You will be prompted for the following information during the set up process
• Device ESN
• Name of Asset (ex. Service Truck 51)
• Year, make, and model
• VIN #
• License plate #
• Mileage Hours
STEP SEVEN
Call Pedigree Technologies support to conrm installation before replacing any of the dash
panels you may have removed during cable installation.
STEP SIX
Snap the tablet into the cradle assembly.
Cradle/LMU Tablet in Cradle/LMU