peerless-AV DS-LED27BDL-6X6 User manual

12020-04-13 #:146-9045-2 (2020-08-20)
DS-LED27BDL Series
*Actual conguration may vary
ENG Installation video for reference only.
Read and follow instruction manual for full installation.

22020-04-13 #:146-9045-2 (2020-08-20)
Wear anti-static gloves.
ENG
Symbols
ENG
WARNING
ENG
x3
Screws must get at
least three full turns

ENG
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.

walls. Before installing make sure the supporting surface will support the combined load of the equipment and

Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING

ENG

32020-04-13 #:146-9045-2 (2020-08-20)
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
2.5mm
1
2
ENG To properly tighten screws: Tighten until screw


4
+1/2
3

42020-04-13 #:146-9045-2 (2020-08-20)
H
IJL M5 x 5mm
set screw
#14 x 1.75"
wood screw
M5 x 8mmM8 x 40mm
A B C
left column right column inside column
Parts List
Description
Aleft column
Bright column
Cinside column
Dvertical spacer
Ehorizontal spacer
Fextrusion connector
G3mm allen wrench two-tip T-handle
HM5 x 5mm set screw
I#14 x 1.75" wood screw
JM5 x 8mm
Kwall plate shim
LM8x40mm
Mtop horizontal asy
Nbottom horizontal asy
Otop left horizontal asy (5X5 only)
Ptop right horizontal asy (5X5 only)
Qbottom left horizontal asy (5X5 only)
Rbottom right horizontal asy (5X5 only)
Sspacer
T5mm allen wrench

ENG
K
wall plate
shim
E
horizontal
spacer
F
extrusion
connector
D
vertical spacer
G
3mm allen wrench
two-tip T-handle
TS
5mm allen
wrench
spacer

52020-04-13 #:146-9045-2 (2020-08-20)
O
M
P
N
Q R
top left
horizontal asy
top horizontal asy
top right
horizontal asy
bottom horizontal asy
bottom left
horizontal asy
bottom right
horizontal asy

62020-04-13 #:146-9045-2 (2020-08-20)
1-1


ENG
Remove and save hardware.
ENG
M,O
M,P
1-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
F (4) H (8)
G
2.5mm
M,P
M,O

72020-04-13 #:146-9045-2 (2020-08-20)
2-1
Optional: If connecting two bottom horizontal

ENG
Remove and save hardware.
ENG
N,R
N,Q
1-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G
G
M,P
M,O

82020-04-13 #:146-9045-2 (2020-08-20)
N,R
N,R
N,Q
N,Q
2-2
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
H (6)
F (3)
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G
2.5mm

92020-04-13 #:146-9045-2 (2020-08-20)
This page intentionally left blank.
ENG

10 2020-04-13 #:146-9045-2 (2020-08-20)
3-1
Use a laser level to keep mounting holes
level.
ENG
3


may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING