peerless-AV DS-LEDIER-5X5 User manual

12020-07-01 #:146-9053-7 (2022-12-22)
DS-LEDIER Series
Compatible with Samsung IER, IFR and IEA series displays
*Actual conguration may vary
ENG Installation video for reference only.
Read and follow instruction manual for full installation.

22020-07-01 #:146-9053-7 (2022-12-22)
Wear anti-static gloves.
ENG
Symbols
ENG
WARNING
ENG
x3
Screws must get at
least three full turns

ENG
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.

walls. Before installing make sure the supporting surface will support the combined load of the equipment and

Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING

ENG

32020-07-01 #:146-9053-7 (2022-12-22)
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
2.5mm
1
2
ENG To properly tighten screws: Tighten until screw


4
+1/2
3

42020-07-01 #:146-9053-7 (2022-12-22)
NM
M5 x 5mm
set screw
#14 x 1.75"
wood screw
A B C
left column right column inside column
Parts List
Description
Aleft column
Bright column
Cinside column
Dvertical spacer
Ehorizontal spacer
Ftop left horizontal extrusion
Gtop right horizontal extrusion
Hbottom left horizontal extrusion
Ibottom right horizontal extrusion
Jconnector plate
Kwall plate shim
LM5 x 8mm
MM5 x 5mm set screw
N#14 x 1.75" wood screw
O3mm allen wrench two-tip T-handle
Ptop horizontal extrusion
Qbottom horizontal extrusion
L
M5 x 8mm
K
wall plate
shim
E
horizontal
spacer
J
connector
plate
D
vertical spacer
3mm allen wrench
two-tip T-handle
O

Refer to parts list included with your model.
ENG

52020-07-01 #:146-9053-7 (2022-12-22)
F
H
I
G
top left
horizontal extrusion
bottom left
horizontal extrusion
bottom right
horizontal extrusion
top right
horizontal extrusion
Q
bottom horizontal extrusion
P
top horizontal extrusion

62020-07-01 #:146-9053-7 (2022-12-22)
1-1


ENG
Remove and save hardware.
ENG
F,P
G,P
1-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
J (4) M (8)
O
2.5mm
F,P
G,P

72020-07-01 #:146-9053-7 (2022-12-22)
2-1
Optional: If connecting two bottom horizontal

ENG
Remove and save hardware.
ENG
I,Q
H,Q
1-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G,P
F,P
O
O

82020-07-01 #:146-9053-7 (2022-12-22)
I,Q
I,Q
H,Q
H,Q
2-2
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
M (6)
J (3)
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
2.5mm
O

92020-07-01 #:146-9053-7 (2022-12-22)
This page intentionally left blank.
ENG

10 2020-07-01 #:146-9053-7 (2022-12-22)
3


may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
3-1
ENG 

(+/- .25") across the height of the video wall and straight (+/- .25") across the width of the video wall.
3-2
Use a laser level to keep mounting holes
level.
ENG
3.375"
(86mm)

7/8" (22mm) minimum
for mounting clearance.
0.27"
(6.9mm)
ENG