peerless-AV LG-WMF86BH User manual

12016-06-2 #:126-9128-1
ENG
LG-WMF86BH
FOR LG-86BH5C

22016-06-2 #:126-9128-1
ENG - This product is designed to be installed on wood stud, solid concrete or cinder block walls. Hardware is
included for wood stud, solid concrete and cinder block installation. Before installing make sure the supporting
surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do
not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Be
careful not to pinch fingers when operating the mount. For support please call customer care at 1-800-865-2112.
WARNING

32016-06-2 #:126-9128-1
Symbols
ENG
WARNING
ENG #
Skip to step.
ENG x3
Screws must get at least three
full turns and fit snug.
ENG
Tools Needed for Assembly.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
+1/2
4
3
5/32"
(4mm)
5/16"
(8mm)
1/2"
(13mm)
Display center.
ENG
Do not overtighten screws.
ENG

42016-06-2 #:126-9128-1
A (1)
wall plate
B (2)
PF632
C (4)
M5 x 6mm
D (1)
4mm allen wrench
Parts List
Part #Description Qty
Awall plate 1 125-P1547
BPF632 2 PF632
CM5 x 6mm socket pin serrated screw 4 510-1114
D4mm allen wrench 1 560-9646
PF632

52016-06-2 #:126-9128-1
1
1b
Wood stud wall.
ENG Concrete/Cinder block.
ENG
1a
1a
ENG - When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that
the wood studs are a minimum of 2" x 4" nominal size. Do not install over gypsum board thicker than 5/8".
WARNING
1a-1 Use stud finder to locate and
mark stud center lines.
ENG

62016-06-2 #:126-9128-1
1a-2
Level wallplate. Mark mounting holes on stud
center lines.
ENG
A
A

72016-06-2 #:126-9128-1
1a-3
2.5"
(64mm)
5/32"
(4mm)
5/32"
(4mm)
Mounting hole must center on stud.
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
1a-4
Level wallplate. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
wood screws provided with PF632 A
A
2

82016-06-2 #:126-9128-1
1b
ENG - When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi. When installing Peerless wall mounts on a cinder block wall, the cinder blocks
must meet ASTM C-90 specifications and have a minimum nominal width of 8". Do not drill into mortar joints!
Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. It is
suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breaking out the back of the hole when entering a void or cavity. Never attach concrete expansion anchors to
concrete or cinder block covered with plaster, drywall or other finishing material.
WARNING
1b-1
1b-2
5/16"
(8mm)
Level wallplate. Mark mounting holes.
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
A
A
2.5"
(64mm)
5/16"
(8mm)
Do not drill into mortar joints.
ENG

92016-06-2 #:126-9128-1
1b-41b-4
1b-31b-3
A
A
1b-41b-4
Level wallplate. Install using concrete
anchors and wood screws provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
Insert anchor flush to concrete.
ENG
C
wood screws provided with PF632
concrete anchors provided with PF632

10 2016-06-2 #:126-9128-1
2
3
C (4)
D
D
backplate from PF632
front plate from PF632
screen side screws from PF632