peerless-AV PA740-S Guide

Installation and Assembly:
Articulating Wall Mount for 22" - 40" (56 - 102 cm) Flat
Panel Displays
Models: PA740, PA740-S
Features:
• Fits 22" - 40" (56 - 102 cm) flat panel displays
• Two tensionable pivot points for extensive adjustment of
viewing angle
• VESA®75/100/200 x 100/200 x 200 compatible
• Frees up space by folding flat against the wall
ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Max UL Load Capacity:
80 lb (36 kg)
I
D
:
0
0
0
0
0
1
8
7
6
2

2 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................5
Installation to Solid Concrete and Cinder Block .....................................................................................................................6
Attaching Adapter Plate to Display with VESA®Mounting Pattern .........................................................................................7
Installing to Peerless PLP Model Adapter Bracket .................................................................................................................8
Cord Management................................................................................................................................................................10
NOTE: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 5/16" (8 mm) bit for concrete and cinder block wall
• 5/32" (4 mm) bit for wood stud wall
• level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
•Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit
(not evaluated by UL)
•Brick Contact Qualified Professional (not evaluated by UL)
•Other or unsure? Contact Qualified Professional
WARNING

3 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
PA740 PA740-S
Description Qty. Part
#
Part
#
Awall mount assembly 1095-P1704 095-4704
Bconcrete anchor 2 590-0320 590-0320
C#14 x 2-1/2" flat head wood screw 2 520-1202 520-2165
D1/4-20 x .5" knob 1560-1162 560-1162
EM4 x 10 mm phillips screw 4 504-9012 520-2027
FM6 x 12 mm phillips screw 4 520-1128 520-2039
GM6 x 20 mm phillips screw 4 520-9402 520-2040
HM8 x 10 mm phillips screw 4 520-1605 520-2605
IM5 x 6 mm phillips screw 4 520-1023 520-2214
J#10 flat washer 4 540-9400 540-9442
Khook plate 1 095-P1561 095-4561
Ladapter plate 1 095-P1721 095-4721
Mcable tie 3560-9711 560-2004
Ncable tie anchor 3590-1290 590-1290
O8-32 x 1/4" flat head screw 3520-1622 520-2622
Pspacer 4 590-5005 590-5003
Parts List
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
A
K
L
IJ
MN OP
B
C
FG HE
D

4 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
Loosen 1/4-20 x 1/2" screws to remove hook bracket (K) from wall mount assembly prior to installation.
1
A
K
1/4-20 X 1/2"
SCREWS

5 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
Installation to Wood Stud Wall
Using a stud finder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to
edge stud finder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall
plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm)
deep. Attach wall mount (A) to wall using two #14 x 2.5" flat head wood screws (C) as shown.
Skip to step 3.
2
A
C
WOOD
STUD
WALL PLATE
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.
Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
WARNING

6 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
Installation to Solid Concrete and Cinder Block
Level and use wall plate as template to mark center
of holes. Drill two 5/16" (8 mm) dia. holes to a
minimum depth of 2.5" (64 mm). Insert anchors (B)
in holes flush with wall. Place wall mount (A) over
anchors and secure with wood screws (C). Make
sure wall mount is level, and tighten all fasteners.
A
C
B
WALL PLATE
SOLID CONCRETE CINDER BLOCK
2
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall plaster/
drywall
concrete concrete
1
3
B
Drill holes and insert anchors (B).
Place plate (A) over anchors (B) and secure with screws (C).
Tighten all fasteners.
2
B
A
C
concrete
surface
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
finishing material. If mounting to concrete surfaces
covered with a finishing surface is unavoidable (not
evaluated by UL), the finishing surface must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when
tightening screws. If plaster/drywall is thicker than
5/8" (16 mm), custom fasteners must be supplied by
installer (not evaluated by UL).
WARNING

7 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
FOR VESA 200 x 100 MOUNTING PATTERN:
Choose hole pattern as shown below. Attach
adapter plate (L) to back of display using four
M4 or M6 screws (E, F, G) as shown below.
Attach hook bracket (K) onto adapter plate (L) using
four M5 x 6 mm screws (I) and #10 washers (J) as
shown.
3
J
K
L
I
Attaching Adapter Plate to Display with VESA 200 or 200 x 100 Mounting Pattern
4
NOTE: For VESA 75 mm and 100 mm patterns, see
following page.
EF, G, H
Attach adapter plate (L) to back of display with four
M4 screws (E) using hole pattern shown below.
Attach adapter plate (L) to back of display with four M6
or M8 screws (F, G, H) using hole pattern shown below.
LL
E, F, G
L
• If screws don't get three complete turns in the
display inserts or if screws bottom out and bracket is
still not tightly secured, damage may occur to display
or product may fail.
WARNING
FOR VESA 200 MOUNTING PATTERN USING
M4 SCREWS:
FOR VESA 200 MOUNTING PATTERN USING
M6 OR M8 SCREWS:

8 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
Attaching Hook Bracket to Display with VESA 75 or 100 Mounting Pattern
FOR VESA®75 MOUNTING PATTERN:
Choose hole pattern as shown below. Attach hook
bracket (K) to back of display using four
M4 x 10 mm screws (E) as shown below.
FOR VESA 100 MOUNTING PATTERN:
Choose hole pattern as shown below. Attach hook
bracket (K) to back of display using four
M4 x 10 mm screws (E) as shown below.
3
For display compatibility please refer to the flat panel display interface list on our website www.peerlessmounts.com
or call customer care for a display specific adapter bracket LC or PLP models (not evaluated by UL).
For Installing to Peerless PLP Model Adapter Plate (not evaluated by UL)
Note: Refer to PLP model adapter plate instruction
sheet for attachment of adapter plate to display.
Note: M5 x 10 mm screws are included with the
PLP model adapter plate.
Attach hook bracket (K) to adapter plate using four
M5 x 10 mm screws.
3
GENERIC ADAPTER PLATE
M5 X 10 mm SCREW
K
EE
KK
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING

9 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
Attaching Tilt Knob to Wall Mount (optional)
For tool-less tilt adjustment, replace one 1/4-20 x
1/2" screw with tilt knob (D). Drive one 1/4-20 x 1/2"
screw four turns and then remove. Hand thread tilt
knob (D) into wall mount (A) leaving 1/4" exposed
thread as shown in front view.
NOTE: Be sure four 1/4-20 x 1/2" screws have 1/4"
exposed thread.
• Do not lift more weight than you can handle.
Use additional man power or mechanical lifting
equipment to safely handle placement of the display.
WARNING
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 20 in. • lb (2.26 N.M.) maximum torque.
• Be careful not to pinch fingers when opening and
closing mount from the wall.
CAUTION
To attach display to wall mount (A), hook tilt bracket
onto four 1/4-20 x 1/2" screws.
Installing and Removing Flat Panel Display
5
1/4-20 X1/2"
SCREWS
A
Adjust display to desired tilt (15° forward,
5° backward), then tighten four 1/4-20 x 1/2" screws.
Hold display securely to remove from mount. Loosen four
1/4-20 x 1/2" screws and lift display away to disengage tilt
bracket from mount.
1/4-20 X1/2"
SCREWS
FRONT VIEW
REPLACE LEFT OR RIGHT
1/4-20 x 1/2" SCREW WITH TILT KNOB
A
D
1/4"
1/4"
4

10 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12
10-32 x 1/2" screws are pretensioned and require
no adjustment. Rotate display by hand to level
display. Roll bracket allows 2° roll adjustment.
6
• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws
to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION
1/4-20 X1/2" SCREWS
ROLL BRACKET
Attach cable tie anchor (N) to top or bottom of wall
arm (A) using 8-32 x 1/4" screw (O) as shown.
Secure cables to wall arm (A) using cable tie (M).
7
Cord Management
CORD
M
O
N
A
A
2° ROLL
7-1