PEERLESS IWB600-WB Guide

1 of 7 ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
Model: IWB600-WB
Installation and Assembly:
Wall Mount for SMARTboard SB685/SB690
Max Load Capacity: 50 lb (22.6 kg)

2 of 7 ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
A
B
C
F
D E
J
H
K
G I
L M N
PARTS LIST
Description Qty. Part #
A
wall plate 1 095-4652
Bupper cross support 1 095-4962
Csupport bracket 2 095-4667
Dvertical support 2 095-4666
Erubber bumper 2 590-1159
F#10 washer 2 540-9442
GM4 x 6 mm phillips screw 2 520-2032
H#10-32 x 3/8 thumb screw 6 560-2107
Iknob 2 560-0223
J1/4 washer 6 540-9444
KM4 nylock nut 4 530-1055
LM5 nylock nut 8 530-1019
MM4 x 8 mm phillips screw 4 520-2237
NM5 x 20 mm phillips screw 8 510-1208

3 of 7 ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
NOTE: Make sure ange of wall bracket is located on top as shown in detail 1
Be sure wall bracket (A) is level and in desired position. Then use wall bracket (A) as a template to mark center
of four mounting holes. Drill four mounting holes. Attach wall bracket (A) to mounting surface using four screws
provided by installer and four 1/4 washers (J) if required. Once secure, wall bracket (A) will be ush with the top of
the vertical bracket (D).
Fasten two M4 x 6 mm phillips screws (G) into ends of wall bracket (A) as shown in Detail 1.
NOTE: Vertical brackets (D) may be used to determine location of wall bracket (A).
1
A
J
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
WARNING
Screws provided by installer
Flange
ATOP
Detail 1
G

4 of 7 ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
Secure SMARTboard channel to upper cross support (B) using eight M5 x 20 mm phillips screws (N) and eight
M5 nylock nuts (L).
NOTE: Make sure to skip attachment point as shown below.
3
B
L
N
Skip attachment point
Skip attachment point
Secure Vertical brackets (D) to wall bracket (A) using two #10-32 x 3/8 thumb screws (H) and #10 at washers
(F).
2
D
F
H
Detail 2
SMARTboard
channel

5 of 7 ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
Secure upper cross support (B) to vertical supports (D) using four M4 x 8 mm phillips screws (M), and
M4 nylock nuts (K).
4
D
K
M
B
Hook SMARTboard into SMARTboard channel on upper cross support (B).
5
SMARTboard
B
B
M
Detail 3
Detail 4
SMARTboard
channel
SMARTboard
channel

6 of 7 ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
H
H
C D
C
I
E
Detail 5
Fasten two support brackets (C) to vertical supports (D) using four #10-32 x 3/8 thumb screws (H).
Slide support brackets (C) up until bottom of SMARTboard rests on support as shown in detail 5.
Tighten four #10-32 x 3/8 thumb screws (H).
6
Fasten knob (I) through outside hole in support bracket (C) to determine rubber bumper (E) placement.
Secure rubber bumper (E) to board.
Repeat on opposite side of board.
7
C

7 of 7 ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
Secure bottom of vertical supports (D) to mounting surface using two screws provided by installer,
and 1/4 washers (J) if required.
NOTE: Make sure mounting surface is suitable to hold the weight of the mount and smart board.
8
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
D
J
Screws provided by
installer