PEERLESS PJF2-UNV Guide

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
1 of 9
For customer care call 1-800-865-2112.
Installation and Assembly Manual:
Vector Pro II™
Models: PJF2-UNV, PJF2-UNV-S
Maximum UL Load Capacity: 50 lb (27 kg)

This product is intended for use with UL
Listed products and must be installed
by a qualied professional installer.
Compatible
model/series*
ENG AEC*,
EXT*,
ADD*,
ACC500*,
CMJ400*,
DCT100,
DCS200,
CMJ500R1.

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
2 of 9
For customer care call 1-800-865-2112.
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillipsscrewdriver
• drill
• 1/4"masonrybitforconcretesurface
• 5/32"bitforwoodstuds
• level
• 3/8"(10mm)socketwrench
• Itistheresponsibilityoftheinstallertoensurethat
theprojectorisproperlyventilated.Feetofchannels
areusedtoraisethemountofftheprojectorsurface.
CAUTION
Note:Readentireinstructionsheetbeforeyoustartinstallationandassembly.
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarningscon-
tainedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,callPeer-
lesscustomercareat1-800-865-2112.
• Thisproductshouldonlybeinstalledbysomeoneofgoodmechanicalaptitude,hasexperiencewithbasicbuilding
construction,andfullyunderstandstheseinstructions.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-
wareandcomponents.
• NeverexceedtheMaximumULLoadCapacity.
• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.Seesuggestedtorquevalueswhereapplicablewithintheseinstructions.
WARNING
Table of Contents
PartsList............................................................................................................................................................................3
InstallationtoWoodJoistorWoodBeamCeilings............................................................................................................ 4
InstallationtoConcreteCeilings........................................................................................................................................ 5
FlushMountApplication .................................................................................................................................................... 6
InstallationtoExtensionColumns ..................................................................................................................................... 7
AttachingAdapterPlatetoProjector.................................................................................................................................. 8
AttachingAdapterPlatetoProjectorMount,ProjectorAlignment ..................................................................................... 9

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
3 of 9
For customer care call 1-800-865-2112.
Beforeyoustartcheckthepartslisttoinsureallofthepartsshownareincluded.
ACD
Note: Actual parts may appear slightly different than illustrated.
E GF H J K L
B
OR
N
MP
T
U
Parts List PJF2-UNV
Part #
PJF2-UNV-S
Part #
Description Qty
Aballandsocketmount 1 055-0011 055-0016
Badapter plate 1 055-1867 055-4867
Cceilingplate 1 580-1042 580-4042
Dextensioncolumnconnector 1 580-1025 580-4025
EM5x.8x10mmsocketpintypeFscrew 1520-1164 520-2031
F#10-32x3/8"spadethumbscrew 1560-1107 560-2107
G#10-32x3/8"serratedwasherheadsocketpinscrew 1 520-1151 520-2151
H#14x2.5phillipshexheadwoodscrew 2 5S1-015-C03 5S1-015-C04
J.25"IDx.56"ODx.26spacer 2 590-1050 590-2071
K#10-32x3/8"socketpinscrew 2 520-1084 520-2084
L#10-32x3/16"slottedsetscrew 3 520-1187 520-2187
Mwasher 4 540-1025 540-2025
NM3x8mmserratedwasherheadsocketpinscrew 4 510-1004 510-2004
OM4x10mmserratedwasherheadsocketpinscrew 4510-1060 510-2060
PM5x10mmserratedwasherheadsocketpinscrew 4510-1126 510-2063
RM6x10mmserratedwasherheadsocketpinscrew 4510-1066 510-2066
T2mmsecurityallenwrench 1560-1097 560-1097
U4mmsecurityallenwrench 1560-9646 560-9646
VM5x20mmserratedwasherheadsocketpinscrew 4510-1065 510-2065
V

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
4 of 9
For customer care call 1-800-865-2112.
H
C
WOODJOIST
Drilltwo5/32"(4mm)dia.holestoaminimum
depthof2.5"(64mm).Attachceilingplate(C)
withtwo#14x2.5"(6mmx65mm)wood
screws(H)asshownusing3/8"(10mm)socket
wrench.
Skip to step 3 for ush mount installation.
Skip to step 4 for extension column
installation.
For Optional Cord Management,
installtwospacers(J)betweenceiling
plate(C)andceiling.
Installation To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings
WOODJOIST
CEILING
H
C
J
• Itistheresponsibilityoftheinstallertoverifythatthe
supportingsurfacewillsafelysupportthecombined
loadofallattachedhardwareandcomponents.
WARNING
1
IMPORTANT: Be sure to drill holes into the
joist CENTER!
CEILING
• WheninstallingPeerlessceilingmountsonawoodjoist/beamcoveredwithgypsumboard(drywall),verifythatthe
joistsorbeamsareaminimumof2"x4"nominalsize.Donotinstallovergypsumboardthickerthan5/8".
• Tightenwoodscrews(H)sothatceilingplate(C)isrmlyattached,butdonotovertighten.Overtighteningcandam-
agethescrews,greatlyreducingtheirholdingpower.
• Nevertighteninexcessof80in•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestuds.Theuseofan"edgetoedge"studnder
ishighlyrecommended.
WARNING

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
5 of 9
For customer care call 1-800-865-2112.
CONCRETECEILING
Drilltwo1/4"(6mm)dia.holestoaminimumdepthof
2.5"(64mm).Attachceilingplate(C)usingtwoconcrete
anchorsand#14x2.5"woodscrews(H)asshownin
Illustration A and 1, 2,and3 (below).Tightenallfasteners.
IMPORTANT: It is the responsibility of the installer to
verify that the ceiling will safely support the combined
load of all attached hardware and components.
Skip to step 3 for ush mount installation.
Skip to step 4 for extension column installation.
Illustration A
Installation to Concrete Ceilings
Use only PEERLESS ACC233 concrete anchors (sold separately).
• FOR DIRECT ATTACHMENT TO LOAD BEARING
CONCRETE ONLY! Concreteexpansionanchorsare
not intendedforattachmenttoconcreteceilingscov-
eredwithalayerofplaster,drywall,orothernishing
material.
WARNING
• Tightenwoodscrewssothatceilingplateisrmly
attached,butdonotovertighten.Overtighteningcan
damagethescrews,greatlyreducingtheirholding
power.
• Nevertighteninexcessof80in•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredinto
thecenterofthestuds.Theuseofan"edgetoedge"
studnderishighlyrecommended.
WARNING
• WheninstallingPeerlessceilingmountsonaconcreteceiling,theceilingmustbeatleast8"thickwithaminimum
compressivestrengthof2000psi.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-
wareandcomponents.
• NeverexceedtheMaximumLoadCapacityof50lb(27kg).
WARNING
2
H
C
CONCRETECEILING
concrete
anchor
1
3
2
Drillholesandinsertanchors(H).
Placeplate(B)overanchors(H)andsecurewithscrews(E).
Tightenallfasteners.
C
H
concrete
surface

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
6 of 9
For customer care call 1-800-865-2112.
Screwballandsocketmount(A)intoceilingplate(C)asshowningure 3.1 (minimum5turns).Alignthenotch
withoneofthefourholesoftheceilingplate(C)andsecureballandsocketmount(A)withaM5x10mmsocket
pinscrew(E)usingsecurityallenwrench(U)asshowningure 3.2
NOTE: Slottedsetscrew(L)isusedtojamagainstthethreadsoftheballandsocketmounttopreventanyexcess
movementoftheballandsocketmount(A).Donotovertightenscrew;overtighteningscrewwilldamagethreads
makingitdifculttoseparatetheproducts.
Skip to step 5.
Flush Mount Application
A
C
A
E
WOODJOIST
CEILING
NOTCH
C
L
3
gure 3.1
gure 3.2

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
7 of 9
For customer care call 1-800-865-2112.
Screwextensioncolumntoceilingplate(C).
Alignthenotchwithoneofthefourholesin
theceilingplate(C)andsecureextension
columnwithaM5x10mmsocketpinscrew
(E)usingsecurityallenwrench(U).See
gure 4.1
Screwextensioncolumnconnector(D)to
extensioncolumn.Alignslotinextension
columnwithoneofthetopholesin
extensioncolumnconnector(D).Insertand
tightenone#10-32x3/8"socketpinscrew
(K)throughextensioncolumnconnector(D)
intoslotonextensioncolumnusingsecurity
allenwrench(U).See gure 4.2
Screwballandsocketmount(A)to
extensioncolumnconnector(D).Alignslot
inballandsocketmount(A)tooneofthe
bottomholesinextensioncolumnconnector
(D).Insertandtightenone#10-32x3/8"
socketpinscrew(K)throughextension
columnconnector intoslotinballandsocket
mount(A)usingsecurityallenwrench(U).
See gure 4.3
Allpipethreadconnectionsbetweentheball
andsocketmount(A),columnconnector
(D),ceilingplate(C)mustbethreadeda
minimumof5turns.
Slottedsetscrews(L)areusedtojam
againstthethreadsofeachconnectingjoint
topreventanyexcessmovement.Donot
overtightenscrews;overtighteningscrews
willdamagethreadsmakingitdifcultto
separatetheproducts.
SLOT
SLOT
C
D
gure 4.1
gure 4.3
gure 4.2
EXTENSION
COLUMN
E
C
Installation to
Extension Column
A
L
A
EXTENSION
COLUMN
SLOT
D
K
EXTENSION
COLUMN
SLOT
DK
L
L
4
ULlistedPeerlessmodel
EXT, AEC, or ADD series
extensioncolumn(sold
separately).

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
8 of 9
For customer care call 1-800-865-2112.
B
MOUNTINGHOLE
GENERICPROJECTOR
Placeprojectorupsidedown.Locateadapterplate(B)withnotchfacingforwardasclosetoprojectorcenterof
gravityaspossiblewithoutcoveringanymountingholes.Loosenchannels,andifthereareonlythreemount-
ingholesremovefourthchannel.Usingonechannelforeachmountinghole,positionfeetofchannelsover
mountingholesasshownbelow.IMPORTANT:Ifprojectordoesnothaveatleastthreemountingholes,donot
use this adapter plate.
NOTE:Someprojectorshavefeetwhichcanberemovedandthecorrespondingthreadedinsertcanbeused
foramountinghole.
NOTE:Oncechannelsareinpositionretightenfasteners.
NOTE:Theprojectoryouareinstallingmaydifferinappearancefromthesampleillustratedbelow.
Attachadapterplate(B)toprojectorusingonescrew(N, O, P, R, or V)foreachchannelasshownbelow.
Tightenallscrews,whilekeepingthecenterofgravity.Besurethatadapterplate(B)isstraight.Adjustthefeet
ofthechannelstokeeptheadapterplatelevel.Tightenallscrewswith4mmsecurityallenwrench(U)orwrench
providedwithprojectormount,whilekeepingthecenterofgravity.IfM3screwsareused,tightenusing2mm
securityallenwrench(T).
NOTE:Projectorswillrequiredifferentsizescrewsformounting.Useacombinationofscrews(N, O, P, R, or V)
andfootadjustmentthatwillresultinchannelsofadapterplate(B)ttingtightlyagainstprojector.IMPORTANT:
Inordertoproperlyengagethethreadsinthemountingholes,thescrewmustbeturnedatleast3fullturns.
Note:Ifusingscrew(N),placewasher(M)betweenscrew(N)andfootofchannel.
FOOTOFCHANNEL
B
• Itistheresponsibilityoftheinstallertoensurethat
theprojectorisproperlyventilated.Feetofchannels
areusedtoraisethemountofftheprojectorsurface.
CAUTION N, O, P, R, or V
5
6
Attaching Adapter Plate to Projector
NOTCHINDICATES
FRONTOFPROJECTOR

ISSUED: 01-14-09 SHEET #: 056-9018-3 11-10-16
Visit the Peerless Web Site at www.peerless-av.com
9 of 9
For customer care call 1-800-865-2112.
Toadjustroll,pitch,andyawloosenthesetscrew
(shownbelow)usingsecurityallenwrench(U)or
standard4mmallenwrench.Youshouldbeabletojust
slightlyloosenthescrewsothatyouradjustmentscan
besetwithouthavingtoholdtheprojector.Moveprojec-
tortodesiredpositionandslowlytightensetscrew.
NOTE: Be sure not to touch the projector while tight-
ening the set screw. This may cause the image to be
unaligned when you let go.
IMPORTANT: Allen wrench is your key for projector
removal. Store it in a safe place.
Attachprojector,withadapterplate(B)alreadyonit,to
theballandsocketmount(A)byinsertingtheballand
socketmountintotheadapterplateconnectionand
twistinguntiltheadapterplatewillnolongerturn(about
75°).Thespringloadedcaptivescrewshouldlineup
withacorrespondingholeontheadapterplate(this
shouldlineupautomaticallywhenthetwoareconnect-
ed).Pushdownandtightenthespringloadedcaptive
screwtosecuretheadapterplatetothemount.Ifnot
usingtheoptionalsecurityfeature,fastenthumbscrew
(F)intheholeoppositethespringloadedcaptivescrew.
OPTIONAL:ForArmorLock™security,insertserrated
washerheadsocketpinsecurityscrew(G)inthehole
oppositethespringloadedcaptivescrew.Tightenwith
securityallenwrench(U).Thiswillpreventtheprojector
frombeingremoved.
NOTE: Be sure to only use the #10-32 x 3/8"
screw (G) (or the thumb screw (F)) opposite the
spring loaded captive screw.
A
WOOD
JOIST
CEILING
PROJECTOR
ADAPTERPLATE
PROJECTOR
WOODJOIST
CEILING
PROJECTOR
CUTAWAYVIEWOF
CEILINGPLATE(C)
G
2
1
F
• Donotliftmoreweightthanyoucanhandle!Usead-
ditionalmanpowerormechanicalliftingequipmentto
safelyhandleplacementoftheprojector!
WARNING
7 8
©2009PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Attaching Adapter Plate to Projector Mount
B
SETSCREW
CAPTIVE
SCREW