PEERLESS RTLA-100 Guide

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
Installation and Assembly:
Articulating Wall Arm for LCD screens
Models: RTLA-100, RTLA-100S, SA 730P, SA 730P-S, D-LA-100, D-LA-100S
Features:
•Fits 10" - 20" LCD screens
• Pivotsandarticulatesinalldirections,evenaroundcornersandcabinets
• Frees up space by folding flat against the wall
• Keeps electronic wires routed internally to reduce clutter Max Load Capacity: 25 lb (11.3 kg)
R

2 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
Note: Read entire instruction sheet before you start installation and assembly.
For customer care call [phone] or [phone].
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.
• This product should only be installed by a qualified professional.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity of 25 lb (11.34 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
WARNING
Tools Needed for Assembly
• studfinder("edgetoedge"studfinderisrecommended)
• phillipsscrewdriver
• drill with 1/4" and 5/32" drill bits
Accessories
• Metal StudAccessory Kit (ACC 908) (Not evaluated by UL)

3 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
D
A
F
I
KG
B
Black Silver
Description Qty. Part # Part #
Awall arm assembly 1 095-0278 095-0278-S
Badapter plate 1 095-1101 095-4101
CM5 x .8 x 10 mm phillips screw 4 520-9250 520-2005
D3/16" allen wrench 1 560-0071 560-0071
EAlligator® concrete anchor 2 590-0097 590-0097
F#14 x 2.5" flat head wood screw 2 520-1202 520-2165
G4 mm allen wrench 1 560-9646 560-9646
Hcord management clip 2 590-1264 590-2164
IM4 x .7 x 12 mm phillips screw 4 504-9013 504-2013
JM4 x .7 x 20 mm phillips screw 4 504-9020 504-2014
Kretaining spacer 4 590-5005 590-5003
Parts List
E
H
C
J

4 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
1
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components.
WARNING
• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws,
greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder
is highly recommended.
WARNING
F
WOOD STUD
WALL
Remove cord covers from wall arm assembly (A) as shown in figure 1.1. Using a stud finder, locate and mark the
edges of the wood stud used in mounting this product. Use of an edge to edge stud finder is highly recommended.
Use a level to draw a vertical line down the center of the stud. Use wall plate as template to mark center of holes
along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm) deep.Attach wall arm assembly (A) to wall
using two #14 x 2.5" flat head wood screws (F) as shown in figure 1.2.
Skip to step 2 on page 6.
A
Installation to Wood Stud Wall
A
CORDCOVERS
fig. 1.1
fig. 1.2

5 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
1
E
concrete
wall
E
Drill holes
and insert
anchors.
Place wall
bracket over
anchor and
secure with
screw.
After
repeating
figure 1.2
tighten all
fasteners.
F
WALL PLATE
fig. 1.3
fig. 1.4
fig. 1.5
F
Installation to Solid Concrete and Cinder Block
Removecordcoversfromwallarm assembly (A)as
shownin figure 1.1. Level and use wall plate as
template to mark center of holes. Drill two 1/4" (6
mm) dia. hole to a minimum depth of 2" (51 mm).
Insert anchors (E) in holes flush with wall as shown
in fig 1.3. Place wall arm (A) over anchor and secure
with wood screw (F) as shown in figure 1.4. Make
sure wall arm is level, and tighten all fasteners. See
figure1.5.
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
orother finishing material asshownbelow. Ifmounting
toconcretewall covered with plaster/drywall is
unavoidable,plaster/drywall(up to 5/8" thick) mustbe
counterboredas shown below.Besure concrete
anchorsdonot pull away fromconcretewhen tighten-
ing screws. If plaster/drywall is thicker than
5/8", custom fasteners must be supplied by installer.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
WARNING
fig. 1.6
A
CUTAWAY VIEW
CORRECT
concrete
plaster/
drywall
INCORRECT
concrete
plaster/
drywall
A
A
E

6 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
B
Screen may appear
slightly different than
illustrated
FOR VESA®75 MOUNTING PATTERN:
Choose hole pattern as shown below.Attach
adapter plate (B) to back of screen using four M4 x
12 mm screws (I) as shown below.
*Note: If hole pattern is in a pocket, attach adapter
plate (B) to back of screen using four M4 x 20 mm
screws (J)andfourretainingspacers(K) as
indicatedbelow.
B
2
Note: If the ball joint feels loose
or too easy to adjust, slightly
tighten cap socket screw until
ball joint feels firmly in place.
Insert two M5 x 10 mm screws
(C) into top two holes of adapter
plate (B) leaving approximately
1/4" of exposed thread. With
slots facing upward, hook
screws onto wall arm ball joint
as shown in figure 3.1.
Insert one M5 screw (C)
through bottom hole of wall arm
ball joint into adapter plate (B)
as shown in figure 3.2.
fig. 3.1 fig. 3.2
1/4"
C
B
WALL ARM
BALL JOINT
C
B
CAP SOCKET
SCREW
3
fig. 2.1 fig. 2.2
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
I
I
K
*For screens with a
hole pattern in a
pocket, spacers (J)
go between adapter
plate (B) and screen.
FORVESA100MOUNTINGPATTERN:
Choosehole patternasshown below.Attach adapterplate
(B) to back of screen using four M4 x 12 mm screws (J) as
shownbelow.
Note: To add security, orderACC 918 for security screws. Refer toACC 918 instruction sheet for installing security screws.

7 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
Route cords through center of cord management clip (H). Next, attach cord management clip (H) to wall arm ball
joint using M5 screw (C) as shown in detail 1. Tighten all four screws (C).
Note:Acord management clip (H) was added for additional cords. If you want to use this additional clip (H), remove
the opposite bottom screw and repeat this step on opposite side of wall arm ball joint.
WALL ARM
BALL JOINT
C
H
4
detail 1
A
5Note: Make sure cords have enough slack to allow full movement of the arm.
Route cords inside arm slots of wall arm assembly (A). Optional: Run power cord through one side of mount and
signalcable(s) through other sidetoavoid interference with thesignal.
Lock cords into place by sliding cord covers onto mount as shown in detail 2. Screen may have to be moved for better
access for sliding on the cord covers.
detail 2
CORDCOVERS

8 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
To get full range of motion and enough tension to hold the screen in any position, simply tighten or loosen cap socket
screw a few turns using 4 mm allen wrench (G).
CAP SOCKET SCREW
• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the screen to fall.
WARNING
6
If more or less tension is desired in the arm pivot points, do the following:
• To increase tension, turn socket screw clockwise with 3/16" allen wrench (D).
• To reduce tension, turn socket screw counter-clockwise with allen wrench (D). Do not turn more than half a turn.
SOCKET
SCREWS
©2005PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
7
Ball join design at screen for easy side-to-side
movementand ±35°of tilt.

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
Installation et assemblage :
Bras mural articulé pour écrans à cristaux liquides
Modèles :RTLA-100, RTLA-100S, SA 730P, SA 730P-S, D-LA-100, D-LA-100S
Caractéristiques :
•Convient aux écrans à cristaux liquides de 25 à 50 cm (10 à 20 po)
• Pivote et s’articule dans toutes les directions, même autour des coins et
desarmoires
• Donne plus d’espace en se repliant à plat contre le mur
• Maintient les fils des fonctions électroniques à l’intérieur afin de réduire
l’encombrement Capacité de charge maximale : 11,3 kg (25 lb)
R

10 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-4 08-23-05
Remarque : Lisez entièrement la fiche d’instructions avant de commencer l’installation et l’assemblage.
Pourleserviceàlaclientèle,appelezle 011+1+[phone].
Outils nécessaires pour l’assemblage
• localisateur de montants (le localisateur de montants « bord à bord » est recommandé)
• tourneviscruciforme
• perceuse à mèches de 6,35 mm (1/4 po) et 3,96 mm (5/32 po)
Accessoires
• Kit d’accessoires pour montants métalliques (ACC 908)
•Ne commencez pas à installer votre produit Peerless avant d’avoir lu et assimilé les instructions et les mises en
garde contenues dans cette fiche d’instructions. Pour toute question concernant les instructions ou les mises en
garde,appelezleservice à la clientèle de Peerless au 011+1+[phone].
•Ceproduitnedoitêtreinstalléqueparunepersonneayantdebonnesaptitudesenmécanique,expérimentéeen
travauxdeconstruction de base, et démontrant une parfaite compréhension de ces instructions.
•Assurez-vousquelasurfacedesupport pourra soutenir sans difficulté la charge combinée de l’équipement, de toute
sa visserie et de tous ses composants.
•Ne montez jamais ce produit sur un mur à montants métalliques sans vous assurer que le montant est en acier de
calibre 25 au minimum, que la cloison sèche a au moins 12,5 mm (1/2 po) d’épaisseur et sans utiliser le kit
d’accessoires Peerless pour montants métalliques.
•Ne dépassez jamais la capacité de charge maximum.
•Si vous effectuez le montage sur un mur à montants en bois, assurez-vous que les vis de montage sont ancrées au
centre des montants. L’usage d’un localisateur « bord à bord » est fortement conseillé.
•Pourleveretpositionnerl’équipement en toute sécurité, faites-vous toujours aider par une autre personne ou utilisez
unmatériel de levage mécanique.
• Serrez fermement les vis, mais sans excès. Un serrage excessif peut endommager les éléments et en réduire
considérablementlepouvoirde maintien. Référez-vous aux couples de serrage suggérés danscesinstructions,dans
les cas applicables.
AVERTISSEMENT !