PEERLESS MIS488 Guide

2300 White Oak Circle. • Aurora, IL 60502 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 11-19-07 SHEET #: 124-9135-2 01-06-11
Installation and Assembly:
Pole PC Mount
Model: MIS488
Max Load Capacity: 25 lb (11.3 kg)
Note: Read entire instruction sheet before you start installation and assembly.
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please
callPeerlesscustomercareat1-800-729-0307.
• Thisproduct should only be installed by a qualified professional.
• Makesure that the wall will safely support the combined load of the equipmentand all attached hardware and compo-
nents.
• NeverexceedtheMaximumLoadCapacityof 25 lb (11.3 kg).
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly, but do not overtighten. Overtighteningcandamage the items, greatly reducingtheirholding
power.
WARNING

2 of 4 ISSUED: 11-19-07 SHEET #: 124-9135-2 01-06-11
Note: Read instruction sheet before you start installation and assembly.
Note: Some parts may appear slightly different than illustrated.
UIQ
NS
W
TY
Safety Belt Kit (Z)
BELTWITH
CINCHBUCKLE BELTWITHOUT CINCHBUCKLE
TRI-BARBELTCLIP CLEARSTRIPS BELTGUIDE
Description Qty. Part #
I3/8-16 hex nut 2 530-9310
Nwasher 2 540-9407
QPC bracket 1 124-T1133
S3/8-16 x 3.25" u-bolt 1 560-1060
T1/4-20 nylock nut 4 530-9413
UPC mounting bracket 1 124-T1134
Wbumper 6 590-1159
Y1/4-20 x 5/8" carraige bolt 4 520-1175
Zsafety belt 1 170-8039-
1
Parts List

3 of 4 ISSUED: 11-19-07 SHEET #: 124-9135-2 01-06-11
• Installermust verify that the supporting surface will safely support the combinedweightof all attached equipment and
hardware.
Attach PC bracket (Q) to PC mounting bracket (U) using four 1/4-20 nylock nuts (T) and four 1/4-20 x 5/8" carraige
bolts(Y).
Attach PC mounting bracket (U) to existing pole
using four washers (N) andfourhexnuts (I).
3
1 2
U
IN
S
Attach six bumper strips (W) to PC bracket (Q).
Q
W
T
Y
Q
U
WARNING
EXISTINGPOLE

4 of 4 ISSUED: 11-19-07 SHEET #: 124-9135-2 01-06-11
NOTE: Use safety belt (Z) instruction in conjuction with this step.
Fasten clear strips to the two slots in PC bracket (Q). Set HD box into computer plate (B). Fasten belt with
cinch buckle to belt without cinch buckle. Place tri-bar belt clips and belt guide onto belt as shown in the safety
belt instructions. Feed the ends of the belt through the PC bracket (Q) slots and through tri-bar belt clip. Cinch
the end of the belt so that the PC is securely held.
NOTE: Trim off the end of the belt if necessary, then lightly burn the end of the belt to prevent fraying.
©2011,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
4
BELTWITH
CINCHBUCKLE BELTWITHOUT
CINCHBUCKLE
TRI-BARBELTCLIP
BELTGUIDE
PC
CLEARSTRIPS
Q
PC
BELTWITH
CINCHBUCKLE
BELTWITHOUT
CINCHBUCKLE