PEERLESS Vision-Point LCV 100 Guide

ISSUED: 11-7-02 SHEET #: 090-9066-5 07-28-05
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 4
E
Model
LCV 100
Part # QTY. DESCRIPTION
A090-7008 1 LCD mount assembly
095-8070 hardware pack
AA 1 4" set screw
CC 1 washer
DD 1 nylock nut
FF 1 1/4" allen wrench
GG 1 3/16" allen wrench
B095-4354 1 adapter plate
C504-2013 4 M4 x .7 x 12 mm phillips screw
D 504-2014 4 M4 x .7 x 20 mm phillips screw
E590-5003 4 .198 x .313 x .437 H retaining spacer
F 520-2175 2 1/4-20 x .5 phillips screw
IMPORTANT! Read entire instruction sheet before you start assembly and installation.
Model: LCV 100
PART LIST
Installation &Assembly - Vision•Point™ Vertical Desktop Mount with Stationary
Base & Vision•Point™ Vertical Desktop Mount with Swivel Base
A
AA
CC
FF
LCV 100
DD
Thread set screw (AA) into the hole on the bottom of LCD assembly (A) using 3/16" allen wrench (GG) as shown.
A
LCV 100
Bottom View
Note: Compare screws to full
scale drawings to make sure you
are using the correct screw.
Note: You may not need all hardware provided
GG
Important: The product is made to support screens with a VESA®compliant hole pattern. For safe mounting, mount-
ing screws must turn at least three times in the screen inserts.
• The LCV 100 can be mounted to most wood and/or wood composite surfaces up to 1.5" thick. Before installation, the
installer MUST ensure that the mounting surface will safely hold the combined weight of the mount and the screen.
The surface must be at least 3/4" thick.
CAUTION
AA
D
CB
F

ISSUED:11-7-02 SHEET #: 090-9066-5 07-28-05
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 4
Drill a 1/2" hole in the desired location of the desktop. Drop set screw (AA) for LCV 100 through the hole (placing
1" base over the hole for LCV 100 model. Fasten LCD assembly with washer (CC) and lock nut (DD) as shown.
1" base
CC
DD
A
AA
FIGURE 1
Attach adapter plate (B) to LCV 100 (A) using 2 1/4-20 x .5 phillips screws (F) as shown.
A
B
F

ISSUED: 11-7-02 SHEET #: 090-9066-5 07-28-05
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 4
hex head screw
FF
Attach mount assembly (A) to monitor using four M4 x 12 mm screws (C) in either the 75 MM or
the 100 MM hole pattern as shown. If necessary use four M4 x 20mm screws (D) and retaining
spacers(E)providedwithadapterplate.
FOR INSTALLING TO VESA 75 MM, 100 MM
Forinstallingthemounting plate to theLCDmonitor,readthe following references:
For installing to VESA 75 mm and VESA 100 mm, see below.
For installing to existing Peerless®adapter plate, go to page 4.
A
In order to be able to safely place the monitor onto the mount, you must first tilt the upright backward about
5°asindicatedbelow:
For the LCV 100 model, loosen the hex head screws using allen wrench (FF), tilt the upright 5° and tighten
the hex head screws.
Other tilt adjustments will be done later.
GENERIC LCD SCREEN
C
ED
or

ISSUED:11-7-02 SHEET #: 090-9066-5 07-28-05
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 4
To adjust upright in a backward tilt position: Hold the screen with one hand, and loosen the hex head screws with
allen wrench (FF).Moveuprightin the desired backward tilt position and tightenhexheadscrews.
To adjust upright in a forward tilt position: hold screen with one hand, and loosen the hex head screws with allen
wrench (FF). Place upright in the desired forward tilt position and tighten hex head screws.
If the upright keeps moving forward use allen wrench (FF) and tighten the hex head screws at the bottom
of the assembly as shown below.
hex head screw
FOR INSTALLING TO EXISTING PEERLESS ADAPTER PLATE
Note: Refertoadapter bracket instruction sheetforattachmentof adapterbracketto monitor.
Attach interface plate (B)toexistingadapter plate using four M5 x 6 mm screws providedwithadapterplateas shown to
theright.
IMPORTANT! Hole on bottom denotes bottom of adapter plate as shown in detail 2.
B
GENERICADAPTER
PLATE
GENERIC LCD SCREEN
M5 X 6 MM SCREWS
(PROVIDEDWITH
ADAPTERPLATE)
DETAIL 2
B
TOP
BOTTOM
FF