PEERLESS PLCM 3 Guide

ISSUED: 03-05-09 SHEET #: 202-9343-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
1 of 5
Read instruction sheet before you start installation and assembly.
Model:PLCM 3
Installation and Assembly -Column Mount for 12" - 22" for
Flat Panel Screens
• Installermustverifythat thesupporting surfacewill
safelysupport thecombinedweight ofall attached
equipmentandhardware.
WARNING
Max Load Capacity: 225 lb (102.3 kg)

ISSUED: 03-05-09 SHEET #: 202-9343-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
2 of 5
D
F
A
B
Note: Some parts may not appear exactly as illustrated.
HI
E
G
J
Fasteners
Description Qt
y
Part #
Aceiling arm box 1 201-1666
Btilt bracket 1 200-1667
Dretaining collar 1 1800-375
EM5 x .8 x 10 mm penta-pin™ screw 4 505-9010
F2.875 OD x 2.125 ID x .062 H fiber washer 1 540-9432
GM10 x 1.5 x 15 mm penta-pin screw 4 520-9263
HM10 x 2" penta-pin tool 1 520-9260
IM5 x 1" penta-pin tool 1 520-9249
JM4 x .7 x 12 mm phillips screw 4 504-9013
Before you begin, make sure all parts shown are included with your product.
PARTS LIST

ISSUED: 03-05-09 SHEET #: 202-9343-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
3 of 5
ceiling plate (not included)
Threadsupport pipe (schedule40 pipe,1.5 x11.5NPT, notincluded) intothreaded fitting inceiling plate
(ULListed CMJ470,not included).Tighten- fouror fivecompleteturns -leaving slotalignedwithonesmall holein
the side of the ceiling plate threaded fitting. Insert and tighten one M5 x .8 x 10 mm penta-pin screw (E) provided
with ceiling plate as shown. Use the M5 penta-pin tool (I) to tighten screw. BY HAND, insert four M10 x 1.5 x 15
mm penta-pin screws (G) into threaded holes in the sides of ceiling arm box (A). Leave approximately 1/4" of
exposedthread.Slide ceilingarmbox(A)andfiberwasher(F)ontoendof supportpipe.Threadretainingcollar (D)
onto threaded end of support pipe. Tighten - four or five complete turns. Slide ceiling arm box (A) down so that it
is on top of retaining collar (D). Insert and tighten one M5 x .8 x 10 mm penta-pin screw (E) into retaining collar (D)
as shown. Insert one M5 penta-pin screw (E) through the tab on the back of ceiling arm box (A). Use M5 penta-
pin tool (I) to tighten screw just enough to stabilize support pipe.
Note: UL Listed ADJ or EXT extension column series can be used in combination with, or in place of support
pipetoachievedifferentlengths.
E
D
A
F
D
G
1/4"
G
E
BACKOF CEILING
ARMBOX
support pipe (not included)
E

ISSUED: 03-05-09 SHEET #: 202-9343-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
4 of 5
Note:Screenandadapter
platemay appeardifferent
thanillustrated.
Using hole pattern for Vesa 75 x 75 shown in detail 1.
Attach tilt bracket (B) to screen using four
M4 x .7 x 12 mm phillips screws (J).
J
SCREEN
B
VESA 75 x 75 VESA 100 x 100
SCREEN
J
Detail 1
Using hole pattern for Vesa 100 x 100 shown in
detail 1.Attach tilt bracket (B) to screen using four
M4 x .7 x 12 mm phillips screws (J).
B

ISSUED: 03-05-09 SHEET #: 202-9343-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
5 of 5
Hang tilt bracket (B) onto ceiling arm box (A).Adjust tilt as desired and tighten four
M10 x 1.5 x 15 mm penta-pin screws (G) securely using M10 penta-pin tool (H).
BA
G
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING