PEERLESS PED 410 Guide

IMPORTANT! Read entire instruction sheet
before you start installation and assembly. Before you start check the parts list to make sure
all of the parts shown are included.
Installation and Assembly- Elevation Pedestal Stand Model:
PED 410, PED 510,
PED 610, PED 710,
TPD 3032, TPD 3536,
A057-1002 (PED 410 only) 1 tube
057-1003 (PED 510 only)
057-1004 (PED 610 only)
057-1005 (PED 710 only)
B4MD-10HS15K 1 base plate
C1390-472 3 fastener plate
D530-9401 2 rubber grommet
E540-9407 6 flat washer
F540-9424 6 M10 lock washer
G5S1-M10-A20 6 M10 x 20 mm screw
H5M9-381-H03 6 rawl bolt
part# qty. part part# qty. part
A
B
C
D
E
F
G
H
I
J
L
K
M
N
O
NOTE:Partsmayappear slighty different then illustated.
TPD trays (TPD 3032 & TPD 3536) can only be used with pedestals
(PED 410, PED 510, PED 610 & PED 710).
P
Q
I540-9400 4 #10 flat washer
J505-9010 6 M5-.8 x 10 mm penta-pin
K2245-081 4 uni. clip
L510-9107 4 1/4-20 x 3/8 phil. RD HD
M095-1021 (TPD 3032 only) 1 support tray
095-1022 (TPD 3536 only)
N046-1002 1 back clamp
O104-1006 1 support plate
P046-1001 1 base ring
Q1390-471 4 support leg
R530-9306 8 5/16 nylock nut
S520-9211 8 5/16-18 x 1 hex screw
V510-9110 6 1/4-20 x 1” phil. bolt
W590-1037 12 glide
X590-1036 12 spacer
Y520-9258 4 #10 x 3/4 penta-pin
Z520-9249 1 penta-pin tool
S
R
V
W
Y
XZ
Available Accessories:
Ratchet Belt (ACC 666)
Pedestals models: PED 410, PED 510, PED 610, PED 710 Tray models: TPD 3032, TPD 3536
ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 4

ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 4
Insert two rubber grommets (D) into two 1.5” dia. holes located on the side of the tube (A) (near the top and
bottom).
A
HA
B
D
D
Position fastener plate (C) inside the tube (A) as shown. Attach base plate (B) using two buttonhead cap screws
(G),lockwashers(F),andflatwashers(E). Tighten securely. Repeat for tworemainingfastenerplates (C).
B
C
G
F
E
A
• For attachment to concrete floor only! All six concrete
expansion anchors must be used. Tighten to 420 in •
lb(47.6N.M.)torque.
WARNING
Mark and drill a 3/8" dia. hole to a minimum depth of 2" at mounting holes located around the base plate (B).
Attach the pedestal to the floor using six concrete expansion anchors (H).

ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 4
Snap twelve glides (W) around edge of base ring (P) as shown.
WP
Attach support plate (O) to tube (A) using four screws (L). Then attach the leg (Q) to the bottom of the plate (O)
usingtwobolts(S)andhexheadnuts(R). Tightensecurely.REPEAT FOR THREEREMAININGSUPPORT
LEGS(Q).
X
V
Attach base ring (P) to support plate (O) using six 1/4-20 x 1” screws (V) and twelve spacers (X). Note: Cutouts
in base ring (P) must be positioned towards the back. If the plate in step 5 was positioned as noted, ring (P) will
hang off the plate in the back.
cutouts
Cutouts
O
L
A
S
Q
R
P
O
A
NOTE: Plate “0” must be positioned
so that the holes in the plate are
closest to what will be the front of
the pedestal. The plate is not cen-
tered over the pedestal so when it is
positioned correctly, more will hang
off the back than the front.

ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 4
Attach TV/Support Tray (M) to Base
Ring (P) using back clamp (N) and two
M5 x .8 x 10 mm penta-pin self tapping
screws(J).Usepenta-pintool(Z) and a
1/4"drivertodrivescrews.
YZ
K
I
J
Using uni-clips (K) and M5 screws (J) (see instruction card in
fastenerpack),or#10x3/4penta-pinscrew(Y)andwashers
(I) (for attachment to mounting bosses if present), or a
combination of both, attach Support Tray (M) to TV bottom.
Attach at four places as close to the four corners of the TV
bottom as possible. Use penta-pin tool (Z) and a 1/4" driver to
drivescrews.
M
O
A
P
N
MJ
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the television.
WARNING