PEERLESS RTLA-100 Guide

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
Installation and Assembly:
Articulating Wall Arm for LCD screens
Models: RTLA-100, RTLA-100S, SA 730P, SA 730P-S, D-LA-100, D-LA-100S
Features:
•Fits 10" - 20" LCD screens
• Pivotsandarticulatesinalldirections,evenaroundcornersandcabinets
• Frees up space by folding flat against the wall
• Keeps electronic wires routed internally to reduce clutter Max Load Capacity: 25 lb (11.3 kg)
R

2 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
Notes:
• Read entire instruction sheet before you start installation and assembly.
• Screen must be attached to the mount to enable tilting.
For customer care call [phone] or [phone].
Tools Needed for Assembly
• studfinder("edgetoedge"studfinderisrecommended)
• phillipsscrewdriver
• drill with 1/4" and 5/32" drill bits
Accessories
• Metal StudAccessory Kit (ACC 908) (Not evaluated by UL)
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.
• This product should only be installed by a qualified professional.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity of 25 lb (11.34 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
WARNING

3 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
A
H
F
Black Silver
Description Qty. Part # Part #
Awall arm assembly 1 095-0385-B 095-0385-S
B3/16" allen wrench 1 560-0071 560-0071
CAlligator® concrete anchor 2 590-0097 590-0097
D#14 x 2.5" flat head wood screw 2 520-1202 520-2165
Ecord management clip 2 590-1264 590-2164
FM4 x .7 x 12 mm phillips screw 4 504-9013 504-2013
GM4 x .7 x 20 mm phillips screw 4 504-9020 504-2014
Hretaining spacer 4 590-5005 590-5003
I5 mm allen wrench 1 560-9640 560-9640
Parts List
G
C
B
DE
I

4 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
1
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhardwareand
components.
WARNING
• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws,
greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder
is highly recommended.
WARNING
D
WOOD STUD
WALL
Remove cord covers from wall arm assembly (A) as shown in figure 1.1. Using a stud finder, locate and mark the
edges of the wood stud used in mounting this product. Use of an edge to edge stud finder is highly recommended.
Use a level to draw a vertical line down the center of the stud. Use wall plate as template to mark center of holes
along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm) deep.Attach wall arm assembly (A) to wall
using two #14 x 2.5" flat head wood screws (D) as shown in figure 1.2.
Skip to step 2 on page 6.
A
Installation to Wood Stud Wall
A
CORDCOVERS
fig. 1.1
fig. 1.2

5 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
1
C
concrete
wall
C
Drill holes
and insert
anchors.
Place wall
bracket over
anchor and
secure with
screw.
After
repeating
figure 1.2
tighten all
fasteners.
D
WALL ARM
fig. 1.3
fig. 1.4
fig. 1.5
D
Installation to Solid Concrete and Cinder Block
Removecordcoversfrom wall armassembly(A)as
shownin figure 1.1. Level and use wall plate as
template to mark center of holes. Drill two 1/4" (6
mm) dia. hole to a minimum depth of 2" (51 mm).
Insert anchors (C) in holes flush with wall as shown
in fig 1.3. Place wall arm (A) over anchor and secure
with wood screw (D) as shown in figure 1.4. Make
sure wall arm is level, and tighten all fasteners. See
figure1.5.
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
orotherfinishingmaterial as shownbelow.Ifmounting
toconcretewallcoveredwith plaster/drywall is
unavoidable,plaster/drywall(upto5/8" thick) must be
counterboredasshownbelow. Besureconcrete
anchorsdonotpullaway from concrete whentighten-
ing screws. If plaster/drywall is thicker than
5/8", custom fasteners must be supplied by installer.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall attached hard-
wareandcomponents.
WARNING
fig. 1.6
A
CUTAWAY VIEW
CORRECT
concrete
plaster/
drywall
INCORRECT
concrete
plaster/
drywall
A
A
C

6 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
Insert two M4 x 12 mm screws (F) into top two holes
ofscreen,leavingapproximately1/4"ofexposed
thread. Hook screws onto keyslots of adapter plate
as indicated in figures 2.1 and 2.2.
*Note: If hole pattern is in a pocket, insert two M4 x
20 mm screws (G) with two retaining spacers (H)
into top two holes of screen as indicated right.
2
3
fig. 2.1
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
Note: Toaddsecurity, orderACC 918 for security
screws.RefertoACC 918 instruction sheet for
installing security screws.
1/4"
H
*For screens with a
hole pattern in a
pocket, spacers (H)
go between adapter
plate and screen.
ADAPTER
PLATE
FOR VESA®75
MOUNTINGPATTERN: FOR VESA100 MOUNTINGPATTERN:
fig. 2.2
F
Screen may appear
slightly different than
illustrated
Insert one M4 screw (F or G) through bottom hole of
adapterplateas shown in figure3.1.
fig. 3.1
F or G
ADAPTER
PLATE

7 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
A
5
Note: Make sure cords have enough slack to allow full movement of the arm.
Route cords inside arm slots of wall arm assembly (A). Optional: Run power cord through one side of mount and
signalcable(s)throughother side to avoidinterferencewiththesignal.
Lock cords into place by sliding cord covers onto mount. Screen may have to be moved for better access for sliding
onthecordcovers.
CORDCOVERS
Route cords through center of cord management clip (E). Next, attach cord management clip (E)toadapterplate
using M4 screw (F or G) as shown in detail 1. Tighten all four screws (F or G).
Note:Acord management clip (E) was added for additional cords. If you want to use this additional clip (E), remove
the opposite bottom screw and repeat this step on opposite side of adapter plate.
F or G
Edetail 1
4

8 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
©2006PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
If more or less tension is desired in the arm pivot points, do the following:
• To increase tension, turn socket screw clockwise with 3/16" allen wrench (B).
• To reduce tension, turn socket screw counter-clockwise with allen wrench (B). Do not turn more than half a turn.
SOCKETSCREWS
NOTE: Adjustmentpoints(socket screws) are factory torqued for optimal performance.Thisfactory torque setting is
recommended to prevent the screen from slipping over time. Ifmoreorlesstension is desired follow this optional
step. You may not achieve optimal torque value if factory torque settings are adjusted.
If more or less tension is desired in tilt mechanism, remove snap caps as shown in detail 2. Insert a flat head screw
driver into slot and pry cap away from tilt mechanism. To adjust tilt, simply tighten or loosen socket screw no more
than half a turn using 5 mm allen wrench (I).To adjust roll, simply tighten or loosen 10-32 nylock nut.
SNAPCAP
SOCKET
SCREW
10-32NYLOCKNUT
detail 2
OPTIONAL
SLOT
• Donot removescreworloosenscrew untilitisnolongerengagedwith themount.Doingsomay causethescreentofall.
WARNING

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 05-09-05 SHEET #: 095-9224-6 08-28-06
Installation et assemblage :
Bras mural articulé pour écrans à cristaux liquides
Modèles :RTLA-100, RTLA-100S, SA 730P, SA 730P-S, D-LA-100, D-LA-100S
Caractéristiques :
•Convient aux écrans à cristaux liquides de 25 à 50 cm (10 à 20 po)
• Pivote et s’articule dans toutes les directions, même autour des coins et
desarmoires
• Donne plus d’espace en se repliant à plat contre le mur
• Maintient les fils des fonctions électroniques à l’intérieur afin de réduire
l’encombrement Capacité de charge maximale : 11,3 kg (25 lb)
R

10 of 24 ISSUED: 05-09-05 SHEET #: 095-9224-7 09-25-06
Remarques :
• Lisez entièrement la fiche d’instructions avant de commencer l’installation et l’assemblage.
• L'écrandoitêtrefixéaubâtipourpermettrel'inclinaison.
Pourleserviceàlaclientèle,appelezle011+1+[phone].
Outils nécessaires pour l’assemblage
• localisateur de montants (le localisateur de montants « bord à bord » est recommandé)
• tourneviscruciforme
• perceuse à mèches de 6,35 mm (1/4 po) et 3,96 mm (5/32 po)
Accessoires
• Kit d’accessoires pour montants métalliques (ACC 908)
•Ne commencez pas à installer votre produit Peerless avant d’avoir lu et assimilé les instructions et les mises en
garde contenues dans cette fiche d’instructions. Pour toute question concernant les instructions ou les mises en
garde,appelezleserviceàlaclientèledePeerless au 011+1+[phone].
•Ceproduitnedoitêtreinstalléqueparunepersonneayantdebonnesaptitudesenmécanique,expérimentéeen
travauxdeconstruction de base, et démontrant une parfaite compréhension de ces instructions.
•Assurez-vousquelasurfacedesupportpourrasoutenirsansdifficultélachargecombinéede l’équipement, de toute
sa visserie et de tous ses composants.
•Ne dépassez jamais la capacité de charge maximum.
•Si vous effectuez le montage sur un mur à montants en bois, assurez-vous que les vis de montage sont ancrées au
centre des montants. L’usage d’un localisateur « bord à bord » est fortement conseillé.
•Pourleveretpositionnerl’équipemententoutesécurité,faites-voustoujoursaider par une autre personne ou utilisez
unmatérieldelevage mécanique.
• Serrez fermement les vis, mais sans excès. Un serrage excessif peut endommager les éléments et en réduire
considérablementlepouvoirdemaintien.Référez-vousauxcouples de serrage suggérés dans ces instructions, dans
les cas applicables.
AVERTISSEMENT !